Главная
Skipped breadcrumb items
STDR5206-B9
Инструкция по эксплуатации Страница: 7

Главная
Stanley
STDR5206-B9
Инструкция по эксплуатации Страница: 7

Stanley STDR5206-B9 — инструкция по использованию отвертки с переменной скоростью [7/30]

Превью страниц Страница 7 / 30

Stanley STDR5206-B9 [7/30] Safety recommendations

ENGLISH

Notes:

a. Never change the position of the forward/reverse switch

(4) while the screwdriver bit is turning.

b. The variable speed trigger switch (5) will NOT function

with the forward/reverse switch (4) in the middle

position.

Variable speed trigger switch (Fig. C)

This screwdriver is equipped with a variable speed On/Off

trigger switch.

1. To start screwdriver, gently squeeze the variable speed

trigger switch (5).

Note: The screwdriver will turn at its slowest speed when

the variable speed trigger switch is depressed slightly. The

screwdriver will turn at its fastest speed when the variable

speed trigger switch is fully depressed.

2. To stop the screwdriver, release the variable speed

trigger switch (5).

Lock-on button (Fig. D)

The lock-on button feature allows the trigger switch to be

locked in the ON position at full speed when continuous

operation for extended periods of time is required.

To lock the lock-on button in the ON position, pull back on

the variable speed trigger switch (5) to start the screwdriver

and push the lock-on button (6) into the screwdriver handle.

Release the variable speed trigger switch while holding the

lock-on button into the screwdriver handle. The screwdriver

will continue to run. To release the lock-on button, pull

variable speed trigger switch back (5) and then release the

trigger.

Note: Operating the screwdriver with the variable speed

trigger switch for an extended period of time may cause the

screwdriver motor to overheat. If the screwdriver gets hot,

stop driving screws and allow it to cool for at least 15

minutes.

Inserting a screwdriver bit (Fig. E)

This tool has a magnetic bit holder that provides convenient

bit changes. To install a bit, simply insert the hex bit shank

(7) into the magnetic bit holder (8) that is located inside the

depth stop (1). Push the bit into the magnetic bit holder until

the magnet holds the bit in place.

Notes:

a. Use only 1” (25 mm) long bits that are designed for use

in driving drywall screws.

b. Make sure the bit size is correct for the drywall screws

being driven. This will usually be a #2 size.

Replacing the magnetic bit holder (Fig. F)

If the magnetic bit holder becomes worn or damaged, it must

be replaced. The replacement bit holder must be of the

same dimensions as the original and have the ANSI

retention groove on the end that is inserted into the tool.

1. Remove the nosepiece (2) by turning it counter

clockwise.

Note: Do not use pliers on the nosepiece. Only use your

hand.

2. Grasp the screwdriver bit (7) with pliers and pull it out of

the magnetic bit holder (8).

3. Grasp the large end of the bit holder with pliers and pull

it straight out of the screwdriver spindle (9).

4. Reverse the process by inserting the replacement

magnetic bit holder into the tool.

Note: When inserting the replacement for magnetic bit

holder, gently tap it into place to make sure it is fully inserted.

Grasp the large end of the magnetic bit holder to ensure the

retention groove (10) is holding the magnetic bit holder in

place in the tool.

5. Reinstall the screwdriver bit and nose piece.

Safety Recommendations

Check the following every time you use the screwdriver:

1. Wear safety glasses or a mask.

2. Use hearing protection.

3. The screwdriver tip is the right size and it is in good

condition.

4. No power cables “live” where you are inserting the

screws.

Note: Failure to follow these safety rules will signiﬁcantly

increase the risk of injury.

(Original instructions)

Stanley STDR5206-B9 — инструкция по использованию отвертки с переменной скоростью [7/30]

Содержание

Похожие устройства