Bort BHR-2000-Pro [6/26] The suction function
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Bort BHR-2000-Pro [6/26] The suction function

Bort BHR-2000-Pro [6/26] The suction function
6
use.
Figure 7 - Detergend application
UNITS WITH DETERGENT APPLICATOR
INCLUDED
Follow manufacturer’s label directions for mixing correct
concentrations of detergent to water ratio through the
pressure washer is approximately 5.4% (1 to 19).
1.Unscrewtotopofdetergentapplicatorandllapplica-
tor with detergent.
2. Replace top on applicator.
3. Remove lance from gun.
4. Attach detergent applicator to gun. ( See Figure 8)
Figure 8 - Attach applicator to gun
5. Apply detergent so it thoroughly covers cleaning sur-
face. Apply from bottom to top to prevent detergent from
sliding down and streaking.
6. Allow detergent to remain on the surface for a few min-
utes. This is a good time to use a brush to lightly scrub
heavily soiled areas.
Never allow detergent to dry on the cleaning surface.
7. Remove detergent applicator from gun and replace
with the lance, or remove applicator from end of lance.
8. Rinse detergent from surface.
NOTE: Flush detergent applicator with clear water fol-
lowing each use.
4. Final Rinse
Start nal rinse at bottom an work upward. Make sure
you thoroughly rinse the surface and that all detergent
has been removed.
5. Shut down
1.Besurealldetergentisushedfromsystem.
2.Turnomotor.
3.Turnowatersupply.
4.Aftermotorandwatersupplyareturnedo,triggergun
to depressurize system.
CAUTION:NEVERturnwatersupplyobeforeturning
motoro.Seriousdamagecouldoccurtothepumpand
or motor.
WARNING! NEVER disconnect high pressure discharge
hose from machine while system is pressurized. To
depressurize, turn motor o, turn water supply o and
squeeze gun trigger 2-3 times.
5. After each use, wipe all surfaces of the pressure wash-
er with a clean, damp cloth.
6. Storage
Do not store pressure washer outdoors.
Do not store pressure washer where it might freeze.
TIPS FOR EXTENDING THE LIFE
OF YOUR PRESSURE WASHER
1. Never operate unit without water.
2. Pressure washer is not meant to pump hot water. Nev-
erconnecttohotwatersupply–thiswillsignicantly
reduce life of the pump.
3. Using detergent other than others brand may cause
damage to pump components (o-rings, etc.).This also
applies to chemicals such as bleach, dish soap, etc.
4. Never operate unit for more than one (1) minute with-
out spraying water. Resulting heat buildup will damage
pump.
5. Before adjusting nozzle’s pressure (high-to-low or low-
to-high) release trigger. Failure to do so will reduce life
of o-rings in lance.
THE SUCTION FUNCTION
You can connect the high pressure cleaner to the water
sources such as taps or pump water from other sources
without pressure.
To work with the water supply without pressure the suc-
tion hose should be removed from the supply and the
gun nozzle should be moved to position “Low” (Figure
14). After that the high pressure cleaner should work idle
for a few seconds to drain the excess water and release
air. Put the suction hose into the water source. After
draining some water the gun nozzle should be moved
to position “High” (Figure 14). Now the high pressure
cleaner is ready to work under high pressure.
TROUBLESHOOTING
1. When switched on, the machine will not start
working.
● Plugisnotwellconnectedorelectricsocketisfaulty.
- Check plug, socket and fuse.
● Themainsvoltageislowerthantheminimumrequire-
ment for start up.
Check that the mains voltage is adequate.
● Thepumpisstuck.
- Refer to after storage instructions. Switch o the
unit and let the motor cool.
● Thermalsafetyhastripped.
- Leave the lance open with water comingthrough.
2. Fluctuating pressure
● Pumpsuckingair
- Check that hoses and connections are airtight
● Valvesdirty,wornoutorstuck.Pumpsealsworn.
- Clean and replace or refer to dealer.
3. Water leaking from the pump
● Sealswornout
- Check and replace, or refer to dealer
4. The motor stops suddenly
● Thermalsafetyswitchhastrippedduetooverheating.
- Check that the mains voltage corresponds to speci-
cations.An extension cable, which is too thin, and

Содержание

Похожие устройства

Скачать