![Gigabyte Z490 AORUS ULTRA G2 (rev. 1.0) — настройки графики и энергопотребления для системных плат [35/56]](/icons/site-icon-64.png){kind=icon}
Gigabyte Z490 AORUS ULTRA G2 (rev. 1.0) — настройки графики и энергопотребления для системных плат [35/56]
Превью страниц
Страница 35 /
56
![Gigabyte Z490 AORUS ULTRA G2 (rev. 1.0) [35/56] Pcie bifurcation support](/views2/1666587/page35/bg23.png)
& RC6(Render Standby)
Allows you to determine whether to let the onboard graphics enter standby mode to decrease power
consumption. (Default: Enabled)
& AC BACK
Determines the state of the system after the return of power from an AC power loss.
Memory The system returns to its last known awake state upon the return of the AC power.
Always On The system is turned on upon the return of the AC power.
Always Off The system stays off upon the return of the AC power. (Default)
IO Ports
& Initial Display Output
Species the rst initiation of the monitor display from the installed PCI Express graphics card or the onboard
graphics.
IGFX
(Note)
Sets the onboard graphics as the rst display.
PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the rst display. (Default)
PCIe 2 Slot Sets the graphics card on the PCIEX8 slot as the rst display.
PCIe 3 Slot Sets the graphics card on the PCIEX4 slot as the rst display.
& Internal Graphics
Enables or disables the onboard graphics function. (Default: Auto)
& DVMT Pre-Allocated
Allows you to set the onboard graphics memory size. Options are: 32M~512M. (Default: 64M)
& DVMT Total Gfx Mem
Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX.
(Default: 256M)
& Aperture Size
Allows you to set the maximum amount of system memory that can be allocated to the graphics card.
Options are: 128MB, 256MB, 512MB, 1024MB, and 2048MB. (Default: 256MB)
& PCIE Bifurcation Support
Allows you to determine how the bandwidth of the PCIEX16 slot is divided. Options: Auto, PCIE x8/x8,
PCIE x8/x4/x4. (Default: Auto)
& Onboard LAN Controller
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
& Audio Controller
Enables or disables the onboard audio function. (Default: Enabled)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.
& Above 4G Decoding
Enables or disables 64-bit capable devices to be decoded in above 4 GB address space (only if your system
supports 64-bit PCI decoding). Set to Enabled if more than one advanced graphics card are installed and
their drivers are not able to be launched when entering the operating system (because of the limited 4 GB
memory address space). (Default: Disabled)
& IOAPIC 24-119 Entries
Enables or disables this function. (Default: Enabled)
(Note) This item is present only when you install a CPU that supports this feature.
- 35 -
Содержание
379- Z490 aorus ultra
- User s manual
- Rev 1001 12me z49utra 1001r
- Identifying your motherboard revision
- Documentation classifications
- Disclaimer
- Copyright
- Z490 aorus ultra motherboard layout z490 aorus ultra motherboard block diagram
- Table of contents
- Chapter 3 appendix 4
- Chapter 2 bios setup 6
- Chapter 1 hardware installation
- Quick installation guide 5 one noise detection cable
- Motherboard driver disc 5 one antenna
- Box contents
- Z490 aorus ultra motherboard layout
- Z490 aorus ultra motherboard 5 four sata cables
- Z490 aorus ultra
- User s manual 5 one g connector
- Two rgb led strip extension cables 5 two thermistor cables
- Z490 aorus ultra motherboard block diagram
- Pci express 3 bus
- Lga1200 cpu
- Ddr4 3200 2933 2666 2400 2133 mhz
- Cpu clk 100 500 mhz pci express 3 bus
- Chapter 1 hardware installation
- 1 installation precautions
- 2 product specifications
- Dual channel memory configuration
- 4 installing the memory
- 3 installing the cpu
- Installing the cpu
- Configuration
- C configuring the graphics card driver
- B connecting the graphics cards
- A system requirements
- 6 setting up amd crossfire nvidia sli configuration
- 6 setting up amd crossfir
- 5 installing an expansion card
- Usb 3 gen 2 type a port red
- Usb 3 gen 1 port q flash plus port
- Usb 3 gen 1 port
- Usb 2 1 port
- Sma antenna connectors 2t2r
- Rj 45 lan port
- Hdmi port
- 7 back panel connectors
- Usb type
- Rear speaker out
- Optical s pdif out connector
- Mic in side speaker out
- Line out front speaker out
- Line in side speaker out
- Center subwoofer speaker out
- 8 internal connectors
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- 2 3 atx_12v_2x2 atx_12v_2x4 atx 2x2 2x4 12v power connectors and 2x12 main power connector
- Cpu_opt water cooling cpu fan header
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- 5 cpu_fan sys_fan1 2 3 4 fan headers
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- The fan pump headers are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis the header also provides speed control for a water cooling pump refer to chapter 2 bios setup settings smart fan 5 for more information
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design
- Sys_fan5_pump sys_fan6_pump system fan water cooling pump headers
- Overheating overheating may result in damage to the cpu or the system may hang
- Sensor in
- Pin no definition
- No pin
- Led_c1 led_c2 rgb led strip headers
- For how to turn on off the lights of the led strip please visit the unique features webpage of gigabyte s website
- Ec_temp1 ec_temp2 temperature sensor headers
- D_led1 d_led2 addressable led strip headers
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip
- Connect the thermistor cables to the headers for temperature detection
- Connect one end of the rgb led strip extension cable to the header and the other end to your rgb led strip the black wire marked with a triangle on the plug of the extension cable must be connected to pin 1 12v of this header the 12v pin marked with an arrow on the other end of the extension cable must be lined up with the 12v of the led strip be careful with the connection orientation of the led strip incorrect connection may lead to the damage of the led strip
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- The headers can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- The headers can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds
- To enable hot plugging for the sata ports refer to chapter 2 bios setup settings io ports sata and rst configuration for more information
- This header can be used to connect a noise detection cable to detect the noise inside the case
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte
- Sata3 0 1 2 3 4 5 sata 6gb s connectors
- Noise_sensor noise detection header
- For more information on the noise detection function please visit the unique features webpage of gigabyte s website
- Chipset supports raid 0 raid 1 raid 5 and raid 10 refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- Before connecting the cable to the header make sure to remove the jumper cap re place the jumper cap if the header is not in use
- The m connectors support m sata ssds or m pcie ssds and support raid configuration please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata hard drive to create a raid array with an m pcie ssd you must set up the configuration in uefi bios mode refer to chapter 3 configuring a raid set for instructions on configuring a raid array
- M2p_sb m2a_cpu m2m_sb m socket 3 connectors
- Follow the steps below to correctly install an m ssd in the m connector step 1 locate the m connector where you will install the m ssd use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink remove the protective film from the thermal pad on the m connector step 2 locate the proper mounting hole based on the length of your m ssd drive if needed move the standoff to the desired mounting hole insert the m ssd into the m connector at an angle step 3 press the m ssd down and then secure it with the screw replace the heatsink and secure it to the original hole remove the protective film from the bottom of the heatsink before replacing the heatsink
- M2m_sb
- M2a_cpu
- Installation notices for the m and sata connectors
- The availability of the sata connectors may be affected by the type of device installed in the m sockets the m2a_cpu connector shares bandwidth with the sata3 1 connector the m2m_sb connector shares bandwidth with the sata3 4 5 connectors refer to the following tables for details
- M2p_sb
- Pled pwr_led power led
- Pin no definition pin no definition
- Nc no connection
- Nc 9 line2_l
- Mic2_r 8 no pin
- Mic2_l 6 sense
- Line2_r 10 sense
- Hd hard drive activity led connects to the hard drive activity led on the chassis front panel the led is on when the hard drive is reading or writing data
- Gnd 7 faudio_jd
- The front panel design may differ by chassis a front panel module mainly consists of power switch reset switch power led hard drive activity led speaker and etc when connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- F_panel front panel header
- System status led
- F_audio front panel audio header
- Speak speaker connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup
- Connects to the power status indicator on the chassis front panel the led is on when the system is operating the led is off when the system is in s3 s4 sleep state or powered off s5
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer
- Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assignments below note the positive and negative pins before connecting the cables
- S3 s4 s5 off
- Ci chassis intrusion header connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed this function requires a chassis with a chassis intrusion switch sensor
- Res reset switch connects to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart
- Pw power switch connects to the power switch on the chassis front panel you may configure the way to turn off your system using the power switch refer to chapter 2 bios setup settings platform power for more information
- Gnd 14 sstx2
- Tx1 9 sbu1 16 rx2
- Gnd 11 vbus 18 d
- Tx1 10 sbu2 17 gnd
- Gnd 11 d2 18 ssrx2
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- The header conforms to usb 3 gen 2 specification and can provide one usb port
- From the power outlet to prevent damage to the usb bracket
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer
- F_usb1 f_usb2 usb 2 1 headers
- Sstx1 13 gnd 20 no pin
- F_u32c usb type
- Sstx1 12 d2 19 vbus
- F_u32 usb 3 gen 1 header
- Ssrx1 9 d1 16 gnd
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord
- Ssrx1 10 nc 17 ssrx2
- Rx1 13 tx2 20 cc2
- Vbus 8 d1 15 sstx2
- Rx1 12 tx2 19 d
- Vbus 8 cc1 15 rx2
- Power 5v 7 gnd
- Vbus 14 gnd
- Power 5v 6 usb dy
- Usb dy 9 no pin
- Pin no definition pin no definition pin no definition
- Pin no definition pin no definition
- Usb dx 8 gnd
- Header with usb 3 gen 2 support
- Usb dx 10 nc
- Power 3 v 8 gnd
- Pin no definition pin no definition
- No pin 9 irq
- Nc 10 nc
- For how to use q flash plus please visit the unique features webpage of gigabyte s website
- Data output 7 chip select
- Data input 11 nc
- Clk 12 rst
- Add in card connectors
- Add in card
- You may connect an spi tpm trusted platform module to this header
- The connectors are used to connect to a gigabyte thunderbol
- Thb_c1 thb_c2 thunderbol
- Supports a thunderbol
- Spi_tpm trusted platform module header
- Qflash_plus q flash plus button
- Q flash plus allows you to update the bios when your system is off s5 shutdown state save the latest bios on a usb thumb drive and plug it into the dedicated port and then you can now flash the bios automatically by simply pressing the q flash plus button the qfled will flash when the bios matching and flashing activities start and will stop flashing when the main bios flashing is complete
- Manually configure the bios settings refer to chapter 2 bios setup for bios configurations
- Cpu dram vga boot status leds
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one minute or use a metal
- Cpu cpu status led dram memory status led vga graphics card status led boot operating system status led
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
- When installing the battery note the orientation of the positive side and the negative side
- Clr_cmos clear cmos jumper
- Used batteries must be handled in accordance with local environmental regulations
- Bat battery
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds
- Always turn off your computer and unplug the power cord from the power outlet before clearing
- The status leds show whether the cpu memory graphics card and operating system are working properly after system power on if the cpu dram vga led is on that means the corresponding device is not working normally if the boot led is on that means you haven t entered the operating system yet
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is
- The cmos values
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost
- After system restart go to bios setup to load factory defaults select load optimized defaults or
- Short clear cmos values
- Replaced with an incorrect model
- Replace the battery 4 plug in the power cord and restart your computer
- Or uncertain about the battery model
- Open normal
- Of the battery the positive side should face up
- Object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds
- Chapter 2 bios setup
- 1 startup screen
- Advanced mode function keys
- 2 the main menu
- 3 favorites f11
- Ring ratio
- Igp rati
- Fclk frequency for early power on
- Enhanced multi core performance
- Cpu upgrade
- Cpu over temperature protectio
- Cpu clock ratio
- Cpu base clock
- Avx offse
- Advanced cpu settings
- 4 tweaker
- Cpu flex ratio override
- Cpu eist functio
- Voltage optimization
- Speed shift technology
- Ring to core offset down bin
- Race to halt rth
- No of cpu cores enabled
- Intel r turbo boost technology
- Intel r speed shift technology inte
- Hyper threading technology
- Ht disabl
- Frequency clipping tv
- Energy efficient turb
- D per core ht disable setting
- Cpu thermal monito
- Cpu flex ratio settings
- C3 state suppor
- C10 state suppor
- Voltage reduction initiated tv
- Turbo ratio 1 core active 10 core active
- Package power limit tdp watts package power limit time
- Package c state limi
- D turbo power limits
- D c states control
- D active turbo ratios
- Cpu enhanced halt c1e
- C8 state support
- C6 c7 state support
- Extreme memory profile x m p
- Dram power limit dram power limit time
- D turbo per core limit contro
- Core current limit amps
- Channel interleaving
- Advanced memory settings
- System memory multiplier
- Rank interleaving
- Memory ref clock
- Memory odd ratio 100 133 or 200 266
- Memory multiplier tweaker
- Memory boot mode
- Soft off by pwr bttn
- Resume by alarm
- Power loading
- Platform power management
- Platform power
- Peg aspm
- Pch aspm
- Dmi aspm
- 5 settings
- Above 4g decoding
- Rc6 render standby
- Pcie bifurcation support
- Onboard lan controller
- Ioapic 24 119 entries
- Io ports
- Internal graphics
- Initial display output
- Dvmt total gfx mem
- Dvmt pre allocated
- Audio controller
- Aperture size
- Ac back
- Ipv6 http support
- Ipv4 pxe support
- Xhci hand off
- Ipv4 http support
- Usb mass storage driver support
- Aggressive lpm support
- Usb configuration
- Sata mode selection
- Sata controller s
- Sata and rst configuration
- Pxe boot wait time
- Nvme configuration
- Network stack configuration
- Network stack
- Media detect count
- Mass storage devices
- Legacy usb support
- Ipv6 pxe support
- Configured as esata
- 3dmark01 enhancement
- Trusted computing
- Software guard extensions sgx
- Reset case open status
- Port 0 1 2 3 4 5
- Pc health status
- Onboard db port led
- Miscellaneous
- Max link speed
- Leds in system power on state
- Leds in sleep hibernation and soft off states
- Intel r ethernet controller
- Intel platform trust technology ptt
- Hot plug
- Ez raid
- Case open
- A b 3 v 5v pch core 12v cpu vaxg
- Temperature warning control
- Temperature interval
- Temperature
- Smart fan 5
- Monitor
- Flow rate
- Fan speed control
- Fan speed
- Fan pump stop
- Fan pump fail warning
- Fan pump control mode
- Fan control use temperature input
- Cpu vcore cpu vccsa cpu vccio ddrvtt a b dram channel a b voltage ddrvpp
- Plug in devices info
- Access level
- 6 system info
- System time
- System language
- System date
- Q flash
- Vga support
- Security option
- Sata support
- Full screen logo show
- Fast boot
- Bootup numlock state
- Boot option priorities
- 7 boot
- Mouse speed
- Lan pxe boot option rom
- Csm support
- Administrator password
- Windows 10 features
- Usb support
- Storage boot option control
- Other pci devices
- Next boot after ac power loss
- Network stack driver support
- User password
- Secure boot
- Preferred operating mode
- Save profiles
- Save exit setup
- Load profiles
- Load optimized defaults
- Exit without saving
- Boot override
- 8 save exit
- Raid levels
- Configuring the onboard sata controller
- Chapter 3 appendix
- C 1 using ez raid
- Before you begin please prepare the following items
- B configuring sata controller mode in bios setup
- A installing sata hard drive s in your computer
- 1 configuring a raid set
- C 3 configuring legacy raid rom
- C 2 uefi raid configuration
- Memory
- Installing the sata raid ahci driver and operating system
- Installing the operating system
- Installation guidelines a 1 installation in ahci mode
- 2 installing an intel optane memory
- 2 installing an inte
- System requirements
- A 2 installation in intel rst premium with intel optane system acceleration mode
- 3 drivers installation
- Regular boot
- 4 debug led codes
- S3 resume
- Recovery
- United states of america federal communications commission statement
- Regulatory notices
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com
- Gigabyte esupport
- Contact us
Похожие устройства
-
Gigabyte B760M D3H DDR4Инструкция пользователя -
Gigabyte GA-880GM-D2HИнструкция по работе -
Gigabyte Z890 EAGLEЭксплуатационная инструкция -
Gigabyte Z890 EAGLE WIFI7Инструкция по применению
-
Gigabyte H610M S2HРуководство по использованию -
Gigabyte Z790 AORUS MASTER XРуководство по работе с устройством -
Gigabyte B660M GAMINGИнструкция пользователя -
Gigabyte B550M DS3H ACИнструкция по работе -
Gigabyte GA-Q87TNРуководство по настройке -
Gigabyte GA-H87TNИнструкция по работе
-
Gigabyte GA-B85TNРуководство пользователя
-
Gigabyte GA-H81TNИнструкция по применению
Изучите настройки графики и управления энергопотреблением для оптимизации работы вашей системы. Узнайте, как настроить графику, память и порты.