![Gigabyte B550I AORUS PRO AX (rev. 1.0) [18/44] F_audio front panel audio header](/img/pdf.png)
Gigabyte B550I AORUS PRO AX (rev. 1.0) [18/44] F_audio front panel audio header
![Gigabyte B550I AORUS PRO AX (rev. 1.0) [18/44] F_audio front panel audio header](/views2/1667810/page18/bg12.png)
9) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, and system status indicator on the chassis to this header according
to the pin assignments below. Note the positive and negative pins before connecting the cables.
System Status LED
S0 On
S3/S4/S5 Off
• PW (Power Switch):
Connects to the power switch on the chassis front panel. You may congure the way to turn off your
system using the power switch (refer to Chapter 2, "BIOS Setup," "Settings\Platform Power," for more
information).
• HD (Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
• RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
• NC:No connection.
• PLED (Power LED):
Connects to the power status indicator on the chassis front panel. The LED
is on when the system is operating. The LED is off when the system is in S3/
S4 sleep state or powered off (S5).
12
9
10
NC
PLED-
PW-
PLED+
PW+
HD-
RES+
HD+
RES-
Power Switch
Hard Drive
Activity LED
Reset Switch
Power LED
The front panel design may differ by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments
are matched correctly.
9
1
10
2
10) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports High Denition audio (HD). You may connect your chassis front
panel audio module to this header. Make sure the wire assignments of the module connector match the
pin assignments of the motherboard header. Incorrect connection between the module connector and the
motherboard header will make the device unable to work or even damage it.
Pin No. Denition Pin No. Denition
1 MIC2_L 6 Sense
2 GND 7 FAUDIO_JD
3 MIC2_R 8 No Pin
4 NC 9 LINE2_L
5 LINE2_R 10 Sense
Some chassis provide a front panel audio module that has separated connectors on each wire
instead of a single plug. For information about connecting the front panel audio module that has
different wire assignments, please contact the chassis manufacturer.
- 18 -
Содержание
- B550i aorus pro ax 1
- Rev 1002 12me b55iapw 1002r 1
- User s manual 1
- Copyright 2
- Disclaimer 2
- Identifying your motherboard revision 2
- B550i aorus pro ax motherboard layout b550i aorus pro ax motherboard block diagram 3
- Chapter 1 hardware installation 3
- Chapter 2 bios setup 1 3
- Chapter 3 appendix 7 3
- Table of contents 3
- B550i aorus pro ax 4
- B550i aorus pro ax motherboard 5 m screw s m standoff s 4
- B550i aorus pro ax motherboard layout 4
- Box contents 4
- Motherboard driver disc 5 one antenna 4
- Note the chip connector is on the back of the motherboard 4
- Two sata cables 5 one rgb led strip extension cable 4
- User s manual 5 one fan power extension cable 4
- Amd b550 5
- Amd socket am4 cpu 5
- B550i aorus pro ax motherboard block diagram 5
- Cpu clk 100 500 mhz pci express 4 3 bus 5
- Ddr4 3200 2933 2667 2400 2133 mhz 5
- 1 installation precautions 6
- Chapter 1 hardware installation 6
- 2 product specifications 7
- 2 productspecifications 7
- 3 installing the cpu 10
- 4 installing the memory 10
- Dualchannelmemoryconfiguration 10
- Installing the cpu 10
- 5 installing an expansion card 11
- 6 back panel connectors 11
- Displayport 11
- Hdmi port 11
- Triple displayconfigurationsfortheonboardgraphics 11
- Usb 3 gen 1 port 11
- Usb 3 gen 1 port q flash plus port 11
- Line in rear speaker out 12
- Line out front speaker out 12
- Mic in center subwoofer speaker out 12
- Q flash plus button 12
- Rj 45 lan port 12
- Sma antenna connectors 2t2r 12
- Usb 3 gen 2 type a port red 12
- Usb type 12
- Audio jack configurations 13
- Please visit gigabyte s website for details on configuring the audio software 13
- To configure 7 channel audio you have to use an hd front panel audio module and enable the multi channel audio feature through the audio driver 13
- 7 internal connectors 14
- 2 atx_12v atx 2x4 12v power connector and 2x12 main power connector 15
- 4 cpu_fan sys_fan1 sys_fan2 fan headers 15
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 15
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from 15
- Overheating overheating may result in damage to the cpu or the system may hang 15
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 15
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers 15
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 15
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 15
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices 16
- Connect one end of the rgb led strip extension cable to the header and the other end to your rgb led strip the black wire marked with a triangle on the plug of the extension cable must be connected to pin 1 12v of this header the 12v pin marked with an arrow on the other end of the extension cable must be lined up with the 12v of the led strip be careful with the connection orientation of the led strip incorrect connection may lead to the damage of the led strip 16
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip 16
- D_led addressable led strip header 16
- For how to turn on off the lights of the led strip please visit the unique features webpage of gigabyte s website 16
- Led_c rgb led strip header 16
- No pin 16
- Pin no definition 16
- The header can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds 16
- The headers can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m 16
- Follow the steps below to correctly install an m ssd in the m connector step 1 before installing the m ssd loosen the screws from the heatsink module and remove the pch heatsink module only the m2a_cpu connector has the heatsink module step 2 locate the proper mounting hole for the m ssd to be installed and then tighten the standoff first insert the m ssd into the m connector at an angle step 3 press the m ssd down and then secure it with the screw replace the heatsink and secure it to the original hole 17
- M socket 3 connectors 17
- M2a_cpu m2b_sb 17
- Note the connector is on the back of the motherboard 17
- Pin no definition 17
- Sata3 0 1 2 3 sata 6gb s connectors 17
- The m connectors support m sata ssds or m pcie ssds and support raid configuration please note that an m pcie ssd cannot be used to create a raid set with an m sata ssd or a sata hard drive refer to chapter 3 configuring a raid set for instructions on configuring a raid array 17
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the sata connectors support raid 0 raid 1 and raid 10 refer to chapter 3 configuring a raid set for instructions on configuring a raid array 17
- F_audio front panel audio header 18
- F_panel front panel header 18
- Connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup 19
- F_u32 usb 3 gen 1 header 19
- Speaker speaker header 19
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer 19
- Tpm trusted platform module header 19
- You may connect a tpm trusted platform module to this header 19
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is 20
- Always turn off your computer before clearing the cmos values after system restart go to bios setup to load factory defaults select load optimized defaults or 20
- Bat battery 20
- Clr_cmos clear cmos jumper 20
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself 20
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord 20
- F_usb1 usb 2 1 header 20
- From the power outlet to prevent damage to the usb bracket 20
- Manually configure the bios settings refer to chapter 2 bios setup for bios configurations 20
- Open normal 20
- Or uncertain about the battery model 20
- Pin no definition 20
- Pin no definition pin no definition 20
- Power 5v 6 usb dy 20
- Power 5v 7 gnd 20
- Replaced with an incorrect model 20
- Rtc power 20
- Short clear cmos values 20
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost 20
- The header conforms to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer 20
- Usb dx 10 nc 20
- Usb dx 8 gnd 20
- Usb dy 9 no pin 20
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds 20
- Used batteries must be handled in accordance with local environmental regulations 20
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 unplug the the battery cable from the battery cable header and wait for one minute 3 plug in the battery cable 4 plug in the power cord and restart your computer 20
- 1 startup screen 21
- Chapter 2 bios setup 21
- 2 the main menu 22
- Advanced mode function keys 22
- 3 favorites f11 23
- 4 tweaker 24
- Ccd0 ccx0 1 rati 24
- Cpu clock control 24
- Cpu clock ratio 24
- Cpu ratio mod 24
- Gfx clock frequenc 24
- Gfx core voltage 24
- Spread spectrum control 24
- Advanced cpu settings 25
- Amd cool quiet function 25
- Ccd contro 25
- Core performance boos 25
- Cppc preferred core 25
- Downcore control 25
- Extremememoryprofile x m p 25
- Global c state contro 25
- Power supply idle contro 25
- Ppc adjustmen 25
- Smt mode 25
- Svm mode 25
- Xmp high frequency suppor 25
- 5 settings 27
- Ac back 27
- High precision event timer 27
- Platform power 27
- Power loading 27
- Resume by alarm 27
- Soft off by pwr bttn 27
- Wake on lan 27
- Above 4g decoding 28
- Cec 2019 ready 28
- Display resolutio 28
- Hd audio controller 28
- Initial display output 28
- Integrated graphics 28
- Io ports 28
- Onboard lan controller 28
- Pciex16 bifurcation 28
- Uma frame buffer siz 28
- Uma mod 28
- 3dmark01 enhancement 30
- Amd cbs 30
- Amd cpu ftpm 30
- Ipv6 http support 30
- Leds in sleep hibernation and soft off states 30
- Leds in system power on state 30
- Media detect count 30
- Miscellaneous 30
- Pc health 30
- Pcieslotconfiguration 30
- Pxe boot wait time 30
- Realtek pcie 2 gbe family controller 30
- Reset case open status 30
- Trusted computing 30
- Case open 31
- Cpu vcore cpu vddp dram channel a b voltage 3 v 5v 12v vcore soc 31
- Fan control mode 31
- Fan control use temperature input 31
- Fan fail warning 31
- Fan speed 31
- Fan speed control 31
- Fan stop 31
- Monitor 31
- Smart fan 5 31
- Temperature 31
- Temperature interval 31
- Temperature warning 31
- 6 system info 32
- Access level 32
- Plug in devices info 32
- Q flash 32
- System date 32
- System language 32
- System time 32
- 7 boot 33
- Boot option priorities 33
- Bootup numlock state 33
- Fast boot 33
- Full screen logo show 33
- Nvme support 33
- Sata support 33
- Security option 33
- Administrator password 34
- Csm support 34
- Lan pxe boot option rom 34
- Network stack driver support 34
- Other pci device rom priority 34
- Storage boot option control 34
- Usb support 34
- Vga support 34
- Preferred operating mode 35
- Secure boot 35
- User password 35
- 8 save exit 36
- Boot override 36
- Exit without saving 36
- Load optimized defaults 36
- Loadprofiles 36
- Save exit setup 36
- Saveprofiles 36
- 1 configuring a raid set 37
- 1 configuringaraidset 37
- A installing sata hard drive s in your computer 37
- B configuringsatacontrollermodeinbiossetup 37
- Beforeyoubegin pleasepreparethefollowingitems 37
- C uefiraidconfiguration 37
- Chapter 3 appendix 37
- Configuringtheonboardsatacontroller 37
- Raid levels 37
- Install the raid driver and operating system 38
- Installing the operating system 38
- 2 drivers installation 39
- Regulatory notices 40
- United states of america federal communications commission statement 40
- Contact us 44
- Gigabyte esupport 44
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com 44
Похожие устройства
- Gigabyte B550 AORUS PRO AC Инструкция
- Gigabyte B550 AORUS PRO Инструкция
- Daikin EWAQ400F-XL Инструкция по эксплуатации
- Daikin EWAQ400F-XL Технические данные
- Daikin EWAQ400F-XL Инструкция по монтажу
- Daikin EWAQ430F-XL Инструкция по эксплуатации
- Daikin EWAQ430F-XL Инструкция по монтажу
- Daikin EWAQ430F-XL Технические данные
- Daikin EWAQ450F-XL Инструкция по эксплуатации
- Daikin EWAQ450F-XL Технические данные
- Daikin EWAQ450F-XL Инструкция по монтажу
- Gigabyte B550 AORUS MASTER Инструкция
- Daikin EWAQ520F-XL Инструкция по эксплуатации
- Daikin EWAQ520F-XL Инструкция по монтажу
- Daikin EWAQ520F-XL Технические данные
- Daikin EWAQ610F-XL Инструкция по эксплуатации
- Daikin EWAQ610F-XL Инструкция по монтажу
- Daikin EWAQ610F-XL Технические данные
- Daikin EWAQ680F-XL Инструкция по монтажу
- Daikin EWAQ680F-XL Инструкция по эксплуатации
Скачать
Случайные обсуждения