Gigabyte R121-340 (rev. 100) Инструкция онлайн

Gigabyte R121-340 (rev. 100) Инструкция онлайн
Motherboard Components
No. Code Descripon
1 SW_ID ID buon with LED
2 USB3_1 USB 3.0 port #1
3 USB3_2 USB 3.0 port #2
4 MLAN Server managemnt LAN port
5 LAN1_2 GbE LAN port #1 /#2
6 COM1_VGA Serial port (top) / VGA port (boom)
7 PMBUS PMBus connector
8 P2 2x4 pin power connector (for CPU)
9 CASE_OPEN Case open intrusion alert header
10 P1 2x12 pin main power connector
11 CPU0 Intel LGA1151 Socket H4
12 BAT Baery socket
13 SATA_0_1 SATA 3 6Gb/s connectors
14 SATA_2_3 SATA 3 6Gb/s connectors
15 SATA_DOM1 SATA port 4 DOM power connector
16 SATA4 SATA 3 6Gb/s connectors (Supports SATA DOM)
17 SATA5 SATA 3 6Gb/s connectors (Supports SATA DOM)
18 SATA_DOM2 SATA port 5 DOM power connector
19 SATA_SGP1 SATA SGPIO header
20 F_USB3_1 USB 3.0 header
21 IPMB IPMB connector
22 BP_1 HDD back plane board header
23 FP_1 Front panel header
24 RISER_1_2 PCIe riser slot (for Gigabyte CRS1022 Only)
25 TPM TPM connector
26 PCIE_2 PCIe x8 slot
27 RISER_1_1 PCIe riser slot (for Gigabyte CRS1022 Only)
28 LED_BMC1 BMC firmware readiness LED
1 2 3 4 5 6
7
8
9
1011
13
14
15
1617
18
19
20
21
22
23
28
24
25
12
26
27
DIMM_P0_A0
DIMM_P0_A1
DIMM_P0_B0
DIMM_P0_B1
Default Enable
123
Default Enable
1 23
ME
Force
Update
ME_UPDATE
BIOS
Recovery
BIOS_RCVR
Enable
Default
3
2
1
Enable
ME
Recovery
BIOS_RCVR
Default
3
2
1
Default Enable
123
Password
Clear
BIOS_PWD
Clear
CMOS
CLR_CMOS
S3
Power On
Select
S3_MASK
Default
Enable
3
2
1
System Components
No Descripon
1 HDD bays
2 Front panel buons and LEDs
3 System fan #3 (FAN3)
4 System fan #5 (FAN5)
5 System fan #7 (FAN7)
6 Fan duct
7 Memory slots
8 Power supply module
9 PCIe riser bracket
10 PCIe riser bracket
CAUTION!
Before you remove or install the system cover:
Make sure the system is not turned on or
connected to AC power.
注意!
在卸下或安装系统机盖之前,请注意
下列事项:
确保系统未开启且未连接到交流电源。
1
2
5
3
7
8
6
9
10
4
Front Panel Header
No. Pin Define
1 Power LED+
3 No Pin
5 Power LED-
7 HDD LED+
9 HDD LED-
11 Power Buon+
13 GND
15 Reset Buon+
17 GND
19 ID Switch+
21 ID Switch-
23 NMI Switch-
No. Pin Define
2 5V Standby
4 ID LED+
6 ID LED-
8 System Status LED+
10 System Status LED-
12 LAN1 Acve LED+
14 LAN1 Link LED-
16 SMBus Data
18 SMBus Clock
20 Case Open
22 LAN2 Acve LED+
24 LAN2 Link LED-
1
2423
2
HDD Back Plane Board Header
1 2
25 26
No. Pin Define
1 BP_SGP_CLK
3 BP_SGP_LOAD
5 BP_SGP_DOUT
7 Key Pin
9 GND
11 BP_LED_G_N
13 BP_SGP_DIN
15 GND
17 GND
19 P_3V3_AUX
21 P_3V3_AUX
23 GND
25 BP_PRESENSE
No. Pin Define
2 No Connect
4 FAN_SGP_Gate
6 GND
8 Reset
10 BP_LED_A_N
12 GND
14 No Connect
16 SMB_BP_DATA
18 SMB_BP_CLK
20 BMC_ACK
22 BMC_REQ
24 Key Pin
26 GND
System Cover
1
2
3
Fan Duct
1
2
Heat Sink
1
2
WARNING!
Please make sure the CPU heat sink installon orientaon.
Failure to observe the warning could result in damage to the equipment.
Memory Populaon Configuraon
Type
Ranks Per
DIMM and
Data Width
Speed (MT/s);
Slot Per Channel (SPC) and
DIMM Per Channel (DPC)
UDIMM
Unbuffered
DDR4 ECC
UDIMM
Unbuffered
DDR4 non-ECC
SR 1.2V
1.2V
2133 2133
Supported
Voltage
DR
2133 2133
2 Slot Per Channel
1DPC 2DPC
All channels in system run at the fastest common frequency.
Mixing ECC and non-ECC UDIMMs anywhere on the plaorm is not
supported.
1 and 2 DPC is supported at 2133MHz.
所有通道模式以最快的频率速度运行。
此主板不支持ECC与非ECC内存模组混合使用。
1 2 DPC 均支持2133MHz速度
System Fan
CAUTION!
Before you remove or install the system fan:
Make sure the system is not turned on or
connected to the AC power.
Disconnect all necessary cable connecons.
Failure to observe these
warnings could result in personal injury or
damage to the equipment.
注意!
确保系统未开机且未连接到交流电源。
断开所有必要的线缆连接。若不遵循这些
警告,可能造成人员伤害或设备损坏。
2
1
No Descripon
1 HDD#3
2 HDD#2
3 HDD#1
4 HDD#0
5 SGPIO header
6 Fan connector#13
7 Fan connector#14
8 Fan connector#11
9 Fan connector#12
10 ODD power connector
11 Fan connector#9
HDD Backplane Board Components
No Descripon
12 Fan connector#10
13 Fan connector#7
14 Fan connector#8
15 Fan connector#5
16 Fan connector#6
17 Fan connector#3
18 Fan connector#4
19 Fan connector#1
20 Fan connector#2
21 Fan connector#15
22 Fan connector#16
Hard Disk Drive and Back Plane Board
5
1
234
6 7 8 9
10
11 12 13
14
15
16 17 18 19
20 21 22
1
2
3
System Front View
System Rear View
No Descripon
1 HDD bay #1
2 HDD bay #2
3 HDD bay #3
4 HDD bay #4
No Descripon
1 Power supply module cord socket
2 VGA port
3 Serial port
4 GbE LAN port
5 10/100/1000 Server management LAN port
6 USB 3.0 ports
7 Full-height riser card bay
8 Low-profile riser card bay
Front & Rear
Power buon/LED:
Green On
Off
Description
System is powered on
System is powered off
State
Speed LED Link/Acvity
LED
Off
State Description
Yellow On 1Gbps data rate
Green On 100Mbps data rate
10Mbps data rate
10/100/1000 LAN LED:
1 2
3
4
7 6 5
No Descripon
5 Power buon with LED
6 ID buon with LED
7 USB 3.0 ports
1
2 3
4 5 6
7 8
PCI Express Card
注意!
在安装扩展卡前,请注意下列事项:
确保系统未开启且未连接到交流电源。
CAUTION!
Before you remove or install the PCI express card:
Make sure the system is not turned on or connected to AC power.
2
3
2
3
1
1
1
4
5
6
4
5
6
注意!
在替换或安装电源前,请注意下列事项:
确保系统未开启且未连接到交流电源。
CAUTION!
Before you remove or install the power supplies:
Make sure the system is not turned on or connected to AC power.
Power Supply
1
1
3
3
4
2
Front Panel LED and Buons
6 复位按钮 按此按钮启动系统。
2
按下按钮启动系统识别功能。ID按钮
1
系统处于开机状态。
系统处于ACPI S1状态(睡眠模式)。
系统未开机或处于ACPIS5状态(关机状态)。
系统处于ACPI S4状态(休眠模式)。
电源按钮和LED 绿色
绿色
恒亮
闪烁
5
恒亮
闪烁
系统和网络之间的链接
网络访问
断开连接/待机
绿色
绿色
LAN1/LAN2活动LED
4
硬盘驱动器定位
硬盘驱动器访问
硬盘驱动器故障
硬盘重建
无硬盘驱动器访问
绿色
橙色
绿色/橙色
闪烁
硬盘驱动器LED
闪烁
编号 名称 颜色 状态 说明
3 系统正常运行
橙色
绿色
系统状态LED
恒亮
恒亮
闪烁
严重情形,可能为下列状况:
电源模块故障
系统风扇故障
电源电压问题
系统温度/电压问题
非严重情形,可能为下列状况:
冗余电源模块故障
系统温度/电压问题
机箱侵入
系统未正常运行,可能为下列状况:
POST错误
NMI错误
处理器或终结器缺失
No. Name Color Status
Description
6
Reset Button Press the button to reset the system.
2 Press the button to activate system identifcation.ID Button
1 System is powered on.
System is in ACPI S1 state (sleep mode).
System is not powered on or in ACPI S5 state (power off).
System is in ACPI S4 state (hibernate mode).
Power Button and LED Green
Green
Solid On
Blink
4
HDD locate
HDD access
HDD fault
HDD rebuild
No HDD access or no HDD fault.
Green
Amber
Green/Amber
On
Blink
On
Blink
HDD Status LED
5
Link between system and network or no access.
Data transmission or receiving is occurring.
No data transmission or receiving is occurring.
Solid On
Blink
Green
Green
LAN1/2 Active/Link LEDs
3 System is operating normally.System Status LED Green
Amber
Solid On
Critical condition, may indicates:
Power module failure
System fan failure
Power supply voltage issue
System temperature
Solid On
Non-critical condition, may indicates:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
System is not ready, may indicates:
POST error
NMI error
Processor or terminator missing
Blink
--
-- -- --
-- --
-- --
-- --
--
--
-- --
--
--
1236 45
R121-340 Quick Installaon Guide/ 快速安装手册
Скачать