MEAN WELL PWM-120-24KN [2/8] Pwm 12

SPECIFICATION

120W PWM Output LED Driver

PWM-120 series

File Name:PWM-120-SPEC 2017-08-04

MODEL

DC VOLTAGE

RATED CURRENT

RATED POWER

OUTPUT

SETUP, RISE TIME

Note.2

HOLD UP TIME (Typ.)

VOLTAGE RANGE 3

Note.

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT (Typ.)

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

SAFETY STANDARDS

Note.5

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVER VOLTAGE

OVER TEMPERATURE

12V 24V 36V 48V

10A 5A 3.4A 2.5A

120W 120W 122.4W 120W

0 ~ 100%

1.47kHz

500ms, 80ms/ 230VAC or 115VAC

16ms/230VAC or 115VAC

90 ~ 305VAC 127 ~ 431VDC

47 ~ 63Hz

PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC @ full load

(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)

88% 90% 90% 90.5%

<0.25mA / 277VAC

108 ~ 120% rated output power

Hiccup mode, recovers automatically after fault condition is removed

20 ~ 95% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

±℃ ℃ ℃0.03%/ (0 ~ 45 ,except 0 ~ 40 for 12V)

10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

860.4K hrs min. Telcordia SR-332 (Bellcore) ; 228.7K hrs min. MIL-HDBK-217F (25 )℃

191*63*37.5mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated and 25 of ambient temperature.current ℃

2. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details

3. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.

4. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected

by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

5. The model certified for CCC(GB19510.14, GB19510.1, GB17743 and GB17625.1) is an optional model . Please contact MEAN WELL for details.

6. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃

or less.

7. Please refer to the warranty statement on MEAN WELL's website at http://www.meanwell.com

Shut down o/p voltage, re-power on to recover

DIMMING RANGE

PWM FREQUENCY (Typ.)

ENVIRONMENT

SAFETY &

EMC

PROTECTION

Shut down o/p voltage, re-power on to recover

15 ~ 17V 28 ~ 34V 41 ~ 46V 54 ~ 60V

1.3A / 115VAC 0.65A / 230VAC 0.55A / 277VAC

PWM-120-12 PWM-120-24 PWM-120-36 PWM-120-48

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃

EMC IMMUNITY

Compliance to EN55015, EN61000-3-2 Class C (@load 60%) ; EN61000-3-3≧

Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Line 2KV)

EMC EMISSION

Note.6

COLD START 60A(twidth=520 s measured at 50% Ipeak) at 230VAC; Per NEMA 410

TOTAL HARMONIC DISTORTION

0.97Kg; 15pcs/15.6Kg/0.87CUFT

MAX. NO. of PSUs on 16A

CIRCUIT BREAKER

4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC

SHORT CIRCUIT

(Please refer to "STATIC CHARACTERISTIC" section)

THD< 20%(@load 60%/115VAC, 230VAC; @load 75%/277VAC)≧≧

(Please refer to “TOTAL HARMONIC DISTORTION” section)

No load power consumption<0.5w for blank-type;standby power consumption<0.5W for DA-type

Tcase=-40 ~ + (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)90℃

Tcase=+90℃

MAX. CASE TEMP.

UL8750( type ”HL” ), CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13,EN62384 independent,

IP67 approved; Design refer to EN60335-1

Shut down o/p voltage, re-power on to recover

DALI STANDARDS Comply with IEC62386-101, 102, 207 for DA-Type only

NO LOAD/STANDBY

POWER CONSUMPTION

MEAN WELL PWM-120-24KN [2/8] Pwm 12

Содержание

Похожие устройства