![TRACO POWER TSP–BCM24A [5/7] Remote on off](/img/pdf.png)
TRACO POWER TSP–BCM24A [5/7] Remote on off
![TRACO POWER TSP–BCM24A [5/7] Remote on off](/views2/1709497/page5/bg5.png)
http://www.tracopower.com Page 5 of 7
Three LED’s also enables a visual evaluation of the functions ofTSP-BCM12, TSP-BCM24(A) and TSP-BCM48(A), mains and
battery directly on site and are in parallel to the signal relay contact.
3.1.1 DC-IN-OK LED:
The DC-IN-OK LED is a green colour LED that indicates the presence of the input voltage.
3.1.2 BATT-OK LED:
The BATT-OK LED is a green colour LED that indicates (if lit) the battery can supply enough current or (if off) battery failure or
not charged.
3.1.3 DC-OUT-OK LED:
The DC-OUT-OK LED is a green colour LED that indicates the status of the output (lit for normal operation)
3.2 Remote ON/OFF:
The¨TSP-BCM12, TSP-BCM24(A) as well as TSP-BCM48(A) provides an external remote on/off function by use of pin 7
and pin 8 at connector J5 (see Fig. 2.1). To switch off the power supply and TSP-BCMxx(A) a connection between
Connector J5 pin 7 and Connector J5, pin 8 by use of a switch has to be made. At open connection between J5 pin 7 and
J5 pin 8 the device is providing the adjusted output voltage.
On the TSP-BCM12 TSP-BCM24(A) as well as theTSP-BCM48(A) a switch is available to switch off the system on site (in
the control cabinet).
Turning the system to OFF state (by switch or remote on/off function) during the battery discharge operation will fully switch
off the system and disconnect the battery. In this condition the system cannot be switched on again. If mains returns and the
system is still in OFF state, the battery will remain disconnected but a very low output voltage may appear (typically 2Vdc,
pulsing). Turning the system to ON state (by switch or remote on/off function) will bring the system back to full function
including battery charging and battery condition test.
3.3 Battery test (Jumper J4):
The TSP-BCM12, TSP-BCM24(A) as well as the TSP-BCM48(A) is designed to monitor the batteries condition. The
battery is loaded with a certain current pulse (the actual load) to monitor the batteries condition. The battery test pulse is
only present as long as the mains is present. The time between the current pulses can be set either to 15 seconds (see
Fig. 2.1, J4 Pin 1 & 2) or to 10 minutes (factory set) (see Fig. 2.1, J4 Pin 2 & 3).
3.4 Temperature sensing:
The TSP-BCM12. TSP-BCM24(A) as well as the TSP-BCM48(A) are designed to operate with temperature compensation
required for proper operation of the battery. The temperature is detected using an external NTC sensor (10k) connected
to the signal connector (J5 pin 9 & pin 10). If the sensor is not connected the device automatically switches to +25°C
constant temperature operation mode.
The factory setting for the battery voltage at +25°C ambient is: 2.28Vdc x 12 cells = 27.4 Vdc or 2.28Vdc x 24 cells =
54.8Vdc. No adjustment is required for the recommended battery. If different batteries are used, the output voltage must
be set accordingly by potentiometer as recommended for +25°C. The initial voltage should be adjusted only when the
battery and temperature sensor are disconnected. (Fig. 2.1).
The set voltage should be measured on J1 of the BCM (BATT-IN).
3.5 Setting the Max. Power Input on the TSP-BCM12, TSP-BCM24(A) or TSP-BCM48(A)
In order to adapt the TSP-BCM12, TSP-BCM24(A) or TSP-BCM48(A) module to the feeding TSP power supply the
maximum input power must be set in accordance with the maximum output power of the TSP Power supply. As the output
voltage of the power supply is approximately 14 Volts (TSP-BCM12) or 28 Volts (TSP-BCM24(A)) or 56Vdc (TSP-
BCM48(A)), the maximum allowed output current of the TSP power supply will be limited by the TSP-BCM module as per
jumper settings shown in the table below.
To ensure that the TSP Power Supply is not overloaded when used with the BCM modules, the jumper J6 needs to be
correctly set before commissioning the system. Incorrect settings for too high currents might damage the power feeding
supply.
Please refer to Fig. 2.1 & paragraph 2.3 for details.
Содержание
- Before installing and using the tsp bcm 12 2
- Connections wire table 2
- Disclaimer 2
- Electrical connections 2
- Mechanical mounting 2
- Step by step wiring instructions 2
- Wire and cable requirements 2
- Connection of tsp bcm12 tsp bcm24 tsp bcm24a tsp bcm48 tsp bcm48a 3
- Fig 1 connection of remote links to power supply 3
- Remote link 3
- Factory setting 4
- Function 4
- Signalling 4
- Tsp bcm12 tsp bcm24 a tsp bcm48 a 4
- Batt ok led 5
- Battery test jumper j4 5
- Dc in ok led 5
- Dc out ok led 5
- Remote on off 5
- Setting the max power input on the tsp bcm12 tsp bcm24 a or tsp bcm48 a 5
- Temperature sensing 5
- Fusing 6
- Wall mounting brackets tsp wmk01 for tsp bcm12 tsp bcm24 tsp bcm24a tsp bcm48 tsp bcm48a 7
Похожие устройства
- TRACO POWER TSP–BCM24A Datasheet
- TRACO POWER TSP–BCM24A Документация
- TRACO POWER TSP–BCM48A Инструкция по эксплуатации
- TRACO POWER TSP–BCM48A Инструкция по установке
- TRACO POWER TSP–BCM48A Документация
- TRACO POWER TSP–BCM48A Datasheet
- Daikin RXY26MTLE Инструкция по эксплуатации
- Daikin RXY26MTLE Руководство по эксплуатации
- TRACO POWER TSP–REM360 Инструкция по эксплуатации
- TRACO POWER TSP–REM360 Datasheet
- TRACO POWER TSP–REM360 Инструкция по установке
- TRACO POWER TSP–REM360 Документация
- TRACO POWER TSP–REM600 Инструкция по эксплуатации
- TRACO POWER TSP–REM600 Datasheet
- TRACO POWER TSP–REM600 Инструкция по установке
- TRACO POWER TSP–REM600 Документация
- Daikin RXY26MTLE Технические данные
- Daikin RXY26MTLE Сервис мануал
- Daikin RXY26MTLE Руководство по вводу в эксплуатацию
- Daikin RXY26MY1 Инструкция по эксплуатации
Скачать
Случайные обсуждения