![Daikin RXYQ34M9W1B [25/28] Introduction](/img/pdf.png)
Daikin RXYQ34M9W1B [25/28] Introduction
![Daikin RXYQ5M9W1B [25/28] Introduction](/views2/1713172/page25/bg19.png)
RXQ5~10 + RXYQ5~48M9W1B
VRVII System air conditioner
4PW21816-1A
Installation manual
20
8.5. Temperature adjustment operation confirmation
After the test run is over, operate the unit normally. (Heating is not
possible if the outdoor temperature is 24°C or higher.)
■ Make sure the indoor and outdoor units are operating normally
(If a knocking sound can be heard in the liquid compression of
the compressor, stop the unit immediately and then energize the
heater for a sufficient length of time before restarting the
operation.)
■ Run each indoor unit one at a time and make sure the
corresponding outdoor unit is also running.
■ Check to see if cold (or hot) air is coming out of the indoor unit.
■ Press the fan direction and fan strength buttons on the indoor
unit to see if they operate properly.
9. SERVICE MODE OPERATION
Vacuuming method
At the first installation, this vacuuming is not required. It is required
only for repair purposes.
1 When the unit is at standstill and under the setting mode 2, set
the required function B (refrigerant recovery operation/
vacuuming operation) to (ON).
- After this is set, do not reset the setting mode 2 until the
vacuuming is finished.
- The H1P led is on and the remote controller indicates
(test operation) and (external control) and the
operation will be prohibited.
2 Evacuate the system with a vacuum pump.
3 Press the button and reset the setting mode 2.
Refrigerant recovery operation method
by a refrigerant reclaimer
1 When the unit is at standstill and under the setting mode 2, set
the required function B (refrigerant recovery operation/
vacuuming operation) to (ON).
- The indoor unit and the outdoor unit expansion valves will
fully open and some solenoid valves will be turned on.
- The H1P led is on and the remote controller indicates
(test operation) and (external control) and the
operation will be prohibited.
2 Cut off the power supply to the indoor units and the outdoor unit
with the circuit breaker. After the power supply to one side is cut
off, cut off the power supply to the other side within 10 minutes.
Otherwise, the communication between the indoor and outdoor
unit may become abnormal and the expansion valves will be
completely closed again.
3 Recover the refrigerant by a refrigerant reclaimer. For details,
see the operation manual delivered with the refrigerant
reclaimer.
10.CAUTION FOR REFRIGERANT LEAKS
(Points to note in connection with refrigerant leaks.)
Introduction
The installer and system specialist shall secure safety against
leakage according to local regulations or standards. The
following standards may be applicable if local regulations are
not available.
The
VRV
System, like other air conditioning systems, uses R-410A
as refrigerant. R-410A itself is an entirely safe non-toxic, non-
combustible refrigerant. Nevertheless care must be taken to ensure
that air conditioning facilities are installed in a room which is
sufficiently large. This assures that the maximum concentration level
of refrigerant gas is not exceeded, in the unlikely event of major leak
in the system and this in accordance to the local applicable
regulations and standards.
Maximum concentration level
The maximum charge of refrigerant and the calculation of the
maximum concentration of refrigerant is directly related to the
humanly occupied space in to which it could leak.
The unit of measurement of the concentration is kg/m
3
(the weight in
kg of the refrigerant gas in 1 m
3
volume of the occupied space).
Compliance to the local applicable regulations and standards for the
maximum allowable concentration level is required.
According to the appropriate European Standard, the maximum
allowed concentration level of refrigerant to a humanly space for
R-410A is limited to 0.44 kg/m
3
.
Pay special attention to places, such as a basements, etc. where
refrigerant can stay, since refrigerant is heavier than air.
Procedure for checking maximum concentration
Check the maximum concentration level in accordance with steps 1
to 4 below and take whatever action is necessary to comply.
1 Calculate the amount of refrigerant (kg) charged to each system
separately.
Cautions for normal operation check
■ Once stopping, the compressor will not restart in
about 5 minutes even if the Run/Stop button of an
indoor unit in the same system is pressed.
■ When the system operation is stopped by the remote
controller, the outdoor units may continue operating
for further 5 minutes at maximum.
■ After the test run, when handing the unit over to the
customer, make sure the electric box lid, the service
lid, and the unit casing are all attached.
ON
BS1 MODE
ON
1
direction of the refrigerant flow
2
room where refrigerant leak has occurred (outflow of all the refrigerant
from the system)
amount of
refrigerant in a
single unit system
(amount of
refrigerant with
which the system is
charged before
leaving the factory)
+
additional charging
amount (amount of
refrigerant added
locally in
accordance with the
length or diameter of
the refrigerant
piping)
=
total amount of
refrigerant (kg) in
the system
NOTE
Where a single refrigerant facility is divided into
2 entirely independent refrigerant systems, use the
amount of refrigerant with which each separate system
is charged.
2
1
Содержание
- Installation manual 1
- System air conditioner 1
- A b a b 2
- Ar pilnu atbildību apliecina ka tālāk uzskaitīto modeįu gaisa kondicionētāji uz kuriem attiecas šī deklarācija 5
- Are in conformity with the following standard s or other normative document s provided that these are used in accordance with our instructions 5
- Atitinka žemiau nurodytus standartus ir arba kitus norminius dokumentus su sąlyga kad yra naudojami pagal mūsų nurodymus 5
- Conform de volgende norm en of één of meer andere bindende documenten zijn op voorwaarde dat ze worden gebruikt overeenkomstig onze instructies 5
- Daikin europe n v 5
- Declara baja su única responsabilidad que los modelos de aire acondicionado a los cuales hace referencia la declaración declara baja su única responsabilidad que los modelos de aire acondicionado a los cuales hace referencia la declaración 5
- Declara sob sua exclusiva responsabilidade que os modelos de ar condicionado a que esta declaração se refere declara sob sua exclusiva responsabilidade que os modelos de ar condicionado a que esta declaração se refere 5
- Declares under its sole responsibility that the air conditioning models to which this declaration relates declares under its sole responsibility that the air conditioning models to which this declaration relates 5
- Declară pe proprie răspundere că aparatele de aer condiţionat la care se referă această declaraţie 5
- Deklarerar i egenskap av huvudansvarig att luftkonditioneringsmodellerna som berörs av denna deklaration innebär att deklarerar i egenskap av huvudansvarig att luftkonditioneringsmodellerna som berörs av denna deklaration innebär att 5
- Deklaruje na własną i wyłączną odpowiedzialność że modele klimatyzatorów których dotyczy niniejsza deklaracja 5
- Der den folgenden norm en oder einem anderen normdokument oder dokumenten entspricht entsprechen unter der voraussetzung daß sie gemäß unseren anweisungen eingesetzt werden 5
- Dichiara sotto sua responsabilità che i condizionatori modello a cui è riferita questa dichiarazione dichiara sotto sua responsabilità che i condizionatori modello a cui è riferita questa dichiarazione 5
- Directives as amended 5
- Directives telles que modifiées 04 richtlijnen zoals geamendeerd 05 directivas según lo enmendado 06 direttive come da modifica 07 ëáèòv fi ˆ ô ó ùúô ô ôèëıâ 08 directivas conforme alteração em 09 директив со всеми поправками 5
- Direktiivejä sellaisina kuin ne ovat muutettuina 5
- Direktive z vsemi spremembami 20 direktiivid koos muudatustega 21 директиви с техните изменения 22 direktyvose su papildymais 23 direktīvās un to papildinājumos 24 smernice v platnom znení 25 değiştirilmiş halleriyle yönetmelikler 5
- Direktiven gemäß änderung 5
- Direktiver med senere ændringer 11 direktiv med företagna ändringar 12 direktiver med foretatte endringer 1 5
- Déclare sous sa seule responsabilité que les appareils d air conditionné visés par la présente déclaration déclare sous sa seule responsabilité que les appareils d air conditionné visés par la présente déclaration 5
- En60335 2 40 5
- Erklärt auf seine alleinige verantwortung daß die modelle der klimageräte für die diese erklärung bestimmt ist erklärt auf seine alleinige verantwortung daß die modelle der klimageräte für die diese erklärung bestimmt ist 5
- Erklærer et fullstendig ansvar for at de luftkondisjoneringsmodeller som berøres av denne deklarasjon innebærer at erklærer et fullstendig ansvar for at de luftkondisjoneringsmodeller som berøres av denne deklarasjon innebærer at 5
- Erklærer under eneansvar at klimaanlægmodellerne som denne deklaration vedrører erklærer under eneansvar at klimaanlægmodellerne som denne deklaration vedrører 5
- Están en conformidad con la s siguiente s norma s u otro s documento s normativo s siempre que sean utilizados de acuerdo con nuestras instrucciones 5
- Estão em conformidade com a s seguinte s norma s ou outro s documento s normativo s desde que estes sejam utilizados de acordo com as nossas instruções 5
- Following the provisions of 02 gemäß den vorschriften der 03 conformément aux stipulations des 04 overeenkomstig de bepalingen van 05 siguiendo las disposiciones de 06 secondo le prescrizioni per 07 ìâ ù úëûë ùˆv è ù íâˆv ùˆv 08 de acordo com o previsto em 09 в соответствии с положениями 5
- Ilmoittaa yksinomaan omalla vastuullaan että tämän ilmoituksen tarkoittamat ilmastointilaitteiden mallit ilmoittaa yksinomaan omalla vastuullaan että tämän ilmoituksen tarkoittamat ilmastointilaitteiden mallit 5
- Irányelv ek és módosításaik rendelkezéseit 5
- Izjavljuje pod isključivo vlastitom odgovornošću da su modeli klima uređaja na koje se ova izjava odnosi 5
- Kinnitab oma täielikul vastutusel et käesoleva deklaratsiooni alla kuuluvad kliimaseadmete mudelid 5
- Low voltage 73 23 eec machinery safety 98 37 eec electromagnetic compatibility 89 336 eec pressure equipment 97 23 eec 5
- Megfelelnek az alábbi szabvány ok nak vagy egyéb irányadó dokumentum ok nak ha azokat előírás szerint használják 5
- Ob upoštevanju določb 20 vastavalt nõuetele 21 следвайки клаузите на 22 laikantis nuostatų pateikiamų 23 ievērojot prasības kas noteiktas 24 održiavajúc ustanovenia 25 bunun koşullarına uygun olarak 5
- On vastavuses järgmis t e standardi te ga või teiste normatiivsete dokumentidega kui neid kasutatakse vastavalt meie juhenditele 5
- Overholder følgende standard er eller andet andre retningsgivende dokument er forudsat at disse anvendes i henhold til vore instrukser 5
- Prohlašuje ve své plné odpovědnosti že modely klimatizace k nimž se toto prohlášení vztahuje 5
- Pw22005 1 5
- Respektive utrustning är utförd i överensstämmelse med och följer följande standard er eller andra normgivande dokument under förutsättning att användning sker i överensstämmelse med våra instruktioner 5
- Respektive utstyr er i overensstemmelse med følgende standard er eller andre normgivende dokument er under forutssetning av at disse brukes i henhold til våre instrukser 5
- Skladni z naslednjimi standardi in drugimi normativi pod pogojem da se uporabljajo v skladu z našimi navodili 5
- Sono conformi al i seguente i standard s o altro i documento i a carattere normativo a patto che vengano usati in conformità alle nostre istruzioni 5
- Sont conformes à la aux norme s ou autre s document s normatif s pour autant qu ils soient utilisés conformément à nos instructions 5
- Spełniają wymogi następujących norm i innych dokumentów normalizacyjnych pod warunkiem że używane są zgodnie z naszymi instrukcjami 5
- Sunt în conformitate cu următorul următoarele standard e sau alt e document e normativ e cu condiţia ca acestea să fie utilizate în conformitate cu instrucţiunile noastre 5
- Sú v zhode s nasledovnou ými normou ami alebo iným i normatívnym i dokumentom ami za predpokladu že sa používajú v súlade s našim návodom 5
- Tad ja lietoti atbilstoši ražotāja norādījumiem atbilst sekojošiem standartiem un citiem normatīviem dokumentiem 5
- Tamamen kendi sorumluluğunda olmak üzere bu bildirinin ilgili olduğu klima modellerinin aşağıdaki gibi olduğunu beyan eder tamamen kendi sorumluluğunda olmak üzere bu bildirinin ilgili olduğu klima modellerinin aşağıdaki gibi olduğunu beyan eder 5
- Teljes felelőssége tudatában kijelenti hogy a klímaberendezés modellek melyekre e nyilatkozat vonatkozik 5
- U skladu sa slijedećim standardom ima ili drugim normativnim dokumentom ima uz uvjet da se oni koriste u skladu s našim uputama 5
- Under iagttagelse af bestemmelserne i 11 enligt villkoren i 12 gitt i henhold til bestemmelsene i 13 noudattaen määräyksiä 14 za dodržení ustanovení předpisu 15 prema odredbama 16 követi a z 17 zgodnie z postanowieniami dyrektyw 18 în urma prevederilor 5
- V platném znění 15 smjernice kako je izmijenjeno 1 5
- Vastaavat seuraavien standardien ja muiden ohjeellisten dokumenttien vaatimuksia edellyttäen että niitä käytetään ohjeidemme mukaisesti 5
- Verklaart hierbij op eigen exclusieve verantwoordelijkheid dat de airconditioning units waarop deze verklaring betrekking heeft verklaart hierbij op eigen exclusieve verantwoordelijkheid dat de airconditioning units waarop deze verklaring betrekking heeft 5
- Visiška savo atsakomybe skelbia kad oro kondicionavimo prietaisų modeliai kuriems yra taikoma ši deklaracija 5
- Vyhlasuje na vlastnú zodpovednosť že tieto klimatizačné modely na ktoré sa vzťahuje toto vyhlásenie 5
- Z późniejszymi poprawkami 18 directivelor cu amendamentele respective 5
- Z vso odgovornostjo izjavlja da so modeli klimatskih naprav na katere se izjava nanaša 5
- Za předpokladu že jsou využívány v souladu s našimi pokyny odpovídají následujícím normám nebo normativním dokumentům 5
- Zandvoordestraat 300 b 8400 oostende belgium 5
-  ó è û ìêˆó ìâ ùô îfiïô ıô úfiù ô ïïô ááú êô î óôóèûìòó fi ùëó úô fiıâûë fiùè úëûèìô ôèô óù è û ìêˆó ìâ ùè ô ëá â ì 5
- Ëïòóâè ìâ ôîïâèûùèî ùë â ı óë fiùè ù ìôóù ï ùˆó îïèì ùèûùèîòó û ûîâ òó ûù ô ô ó ê úâù è ë úô û ïˆûë 5
- Ürünün talimatlarımıza göre kullanılması koşuluyla aşağıdaki standartlar ve norm belirten belgelerle uyumludur 5
- Декларира на своя отговорност че моделите климатична инсталация за които се отнася тази декларация 5
- Заявляет исключительно под свою ответственность что модели кондиционеров воздуха к которым относится настоящее заявление 5
- Соответствуют следующим стандартам или другим нормативным документам при условии их использования согласно нашим инструкциям 5
- Съответстват на следните стандарти или други нормативни документи при условие че се използват съгласно нашите инструкции 5
- Combination 6
- Installation manual 6
- Introduction 6
- Ntroduction 6
- Ain components 7
- Election of location 7
- Main components 7
- Optional accessories 7
- Selection of location 7
- Standard supplied accessories 7
- Technical and electrical specifications 7
- Technical and electrical specifications 7
- Inspecting and handling the unit 8
- Npacking and placing the unit 8
- Nspecting and handling the unit 8
- Unpacking and placing the unit 8
- Connecting the refrigerant piping 9
- Efrigerant piping 9
- Refrigerant piping 9
- Selection of piping material 9
- Precautions when knocking out knock holes 10
- After all the piping has been connected use nitrogen to perform a gas leak check 11
- After the work is finished make sure to check that there is no gas leak 11
- Cautions for installation of multiple outdoor units 11
- Change to pattern 1 or 2 11
- If the overall equivalent piping length is 90 m be sure to enlarge the pipe diameter of the liquid side and gas side main piping this does not apply to rx y q5 type 11
- If the recommended pipe size is not available stick to the original pipe diameter which may result in a small capacity decrease 11
- Oil remains in the outdoor unit c when the system stops 11
- Oil remains in the outdoor unit that stops 11
- Pattern 1 11
- Pattern 2 11
- Precautions when selecting branch piping 11
- Prohibited pattern 11
- Prohibited pattern change to pattern 1 or 2 11
- See the following table for tightening torque applying too much torque may cause the flares to crack 11
- The piping between the outdoor units must be routed level or slightly upward to avoid the risk of oil detention into the piping side 11
- To avoid the risk of oil retention to the stopping unit side always connect the stop valve and the piping between outdoor units as shown in the figure a or figure b 11
- When you keep on tightening the flare nut with a spanner there is a point where the tightening torque suddenly increases from that position further tighten the flare nut within the angle shown below 11
- You must use a torque wrench but if you are obliged to install the unit without a torque wrench you may follow the installation method mentioned below 11
- Example of connection 13
- Example unit 8 b c d e f g p 40 m 13
- Model amount of refrigerant 14
- Checking of unit and installation conditions 15
- Leak test and vacuum drying 15
- Pipe insulation 15
- Stop valve operation procedure 15
- Additional refrigerant charge 16
- Field wiring 17
- Ield wiring 17
- Internal wiring parts table 17
- General cautions 18
- Optional parts cool heat selector 18
- Power circuit and cable requirements 18
- Do not connect wiring of different thicknesses to the power terminal block slack in the power wiring may cause abnormal heat 19
- Examples 19
- Field line connection 19
- Field line connection transmission wiring and cool heat selection 19
- For wiring use the designated power wire and connect firmly then secure to prevent outside pressure being exerted on the terminal board 19
- In case of rx y q5 16 see figure 14 19
- L1 l2 l3 n phase of the power cord should be clamped to the plastic bracket using field supplied clamp material 19
- Over tightening the terminal screws may break them 19
- Precautions when connecting the ground 19
- Precautions when laying power wiring 19
- See the table below for tightening torque for the terminal screws 19
- See figure 19 19
- System example see figure 11 19
- The green and yellow striped wrapped wires should be used for grounding see figure 10 19
- Use an appropriate screwdriver for tightening the terminal screws a screwdriver with a small head will strip the head and make proper tightening impossible 19
- Use round pressure terminals for connections to the power terminal block 19
- When connecting wiring which is the same thickness do as shown in the figure below 19
- When none are available follow the instructions below 19
- When pulling the ground wire out wire it so that it comes through the cut out section of the cup washer an improper ground connection may prevent a good ground from being achieved 19
- Fixing field line connection see figure 12 20
- In case of rxyq18 48 see figure 15 20
- Picking power line and transmission line 20
- Sequential start 20
- Setting the cool heat operation heat pump unit only 20
- Before operation 21
- Checks before initial start up 21
- Efore operation 21
- Service precautions 21
- Field setting 22
- Led state 22
- Location of the dip switches leds and buttons 22
- Opening the switch box and handling the switches 22
- Setting mode 1 22
- Setting the dip switches 22
- Setting the mode 22
- Setting the push button switch bs1 5 22
- Abnormal 23
- Check the led indication in the field marked 23
- Confirmation of the set mode 23
- For function 23
- Indication of cool heat selection setting 23
- Indication of low noise operation state 23
- Indication of power consumption limitation setting 23
- Indication of the present operation state 23
- Normal 23
- Only the noise of level 3 level 2 level 1 for function f 23
- Only the power consumption of level 1 level 2 level 3 23
- Operation 23
- Possible settings for function a b c and g are on or off 23
- Possible settings for function d 23
- Possible settings for function e and f 23
- Push the button according to the required function a g the led indication that matches the required function is shown below in the field marked 23
- Push the button according to the required setting possibility as shown below in the field marked 23
- Push the button and the setting is defined 23
- Refer to the service manual for more details and for other settings 23
- Setting mode 2 23
- Setting procedure 23
- Standard operation factory setting 23
- The following items can be confirmed by setting mode 1 h1p led is off 23
- The h1p led is on 23
- The noise of level 3 level 2 level 1 23
- Under preparation or under test operation 23
- When the button is pushed again the operation starts according to the setting 23
- When the button is pushed the current setting is defined 23
- Performing the test operation 24
- Test operation 24
- Aution for refrigerant leaks 25
- Caution for refrigerant leaks 25
- Ervice mode operation 25
- Introduction 25
- Maximum concentration level 25
- Procedure for checking maximum concentration 25
- Service mode operation 25
- Temperature adjustment operation confirmation 25
- Disposal requirements 26
- Isposal requirements 26
- Pwen21816 1a 28
Похожие устройства
- Daikin RXYQ38M9W1B Технические данные
- Daikin RXYQ36M9W1B Технические данные
- Daikin RXYQ36M9W1B Руководство по вводу в эксплуатацию
- Daikin RXYQ38M9W1B Руководство по вводу в эксплуатацию
- Daikin RXYQ36M9W1B Инструкция по эксплуатации
- Daikin RXYQ38M9W1B Инструкция по эксплуатации
- Daikin RXYQ36M9W1B Инструкция по монтажу
- Daikin RXYQ38M9W1B Инструкция по монтажу
- Daikin RXYQ40M9W1B Технические данные
- Daikin RXYQ42M9W1B Технические данные
- Daikin RXYQ40M9W1B Руководство по вводу в эксплуатацию
- Daikin RXYQ42M9W1B Руководство по вводу в эксплуатацию
- Daikin RXYQ40M9W1B Инструкция по эксплуатации
- Daikin RXYQ42M9W1B Инструкция по эксплуатации
- Daikin RXYQ42M9W1B Инструкция по монтажу
- Daikin RXYQ40M9W1B Инструкция по монтажу
- Daikin RXYQ44M9W1B Технические данные
- Daikin RXYQ46M9W1B Технические данные
- Daikin RXYQ44M9W1B Руководство по вводу в эксплуатацию
- Daikin RXYQ44M9W1B Инструкция по эксплуатации