Home
Главная
Ariston
Варочная Панель
7HPF 640S
Инструкция по эксплуатации Страница: 4

Ariston 7HPF 640S Инструкция по эксплуатации онлайн [4/24] 65959

There is an adjustable

L-shaped pipe fitting on the

appliance supply ramp and this is fitted with a seal in

order to prevent leaks. The seal must always be replaced

after rotating the pipe fitting (seal provided with

appliance). The gas supply pipe fitting is a threaded 1/2

gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a

threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas

cylindrical male attachment.

These pipes must be installed so that they are never longer

than 2000 mm when fully extended. Once connection has

been carried out, make sure that the flexible metal pipe

does not touch any moving parts and is not compressed.

! Only use pipes and seals that comply with current

national regulations.

Checking the tightness of the connection

! When the installation process is complete, check the

pipe fittings for leaks using a soapy solution. Never use a

flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than

default type (indicated on the rating plate at the base of

the hob or on the packaging), the burner nozzles should

be replaced as follows:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner, and

replace them with nozzles for the new type of gas (see

table 1 “Burner and nozzle characteristics”).

3. Reassemble the parts following the above procedure in

the reverse order.

4. Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Sticker are available from any of our Service Centres.

• Adjusting the burners’ primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment screw,

which is positioned in or next to the tap pin, until the

flame is small but steady.

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame does not go out.

4. Some appliances have a safety device (thermocouple)

fitted. If the device fails to work when the burners are set

to the low flame setting, increase this low flame setting

using the adjusting screw.

5. Once the adjustment has been made, replace the seals

on the by-passes using sealing wax or a similar

substance.

! If the appliance is connected to liquid gas, the regulation

screw must be fastened as tightly as possible.

! Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Stickers are available from any of our Service Centres.

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet pipe (in order

to comply with current national regulations).

DATA PLATE

Electrical

connections

See data plate

This appliance conforms to the

following European Economic

Community directives:

-2006/95/EEC dated 12/12/06

(Low Voltage) and subsequent

amendments

- 2004/108/EEC dated 15/12/04

(Electromagnetic Compatibility)

and subsequent amendments

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 2009/142/EEC dated 30/11/09

(Gas) and subsequent

amendments.

- 2002/96/EC and subsequent

amendments.

Содержание

Похожие устройства

GB There is an adjustable L shaped pipe fitting on the appliance supply ramp and this is fitted with a seal in order to prevent leaks The seal must always be replaced after rotating the pipe fitting seal provided with appliance The gas supply pipe fitting is a threaded 1 2 gas cylindrical male attachment to the low flame setting increase this low flame setting using the adjusting screw Connecting a flexible jointless stainless steel pipe to a threaded attachment The gas supply pipe fitting is a threaded 1 2 gas cylindrical male attachment These pipes must be installed so that they are never longer than 2000 mm when fully extended Once connection has been carried out make sure that the flexible metal pipe does not touch any moving parts and is not compressed Only use pipes and seals that comply with current national regulations Checking the tightness of the connection When the installation process is complete check the pipe fittings for leaks using a soapy solution Never use a flame Adapting to different types of gas To adapt the hob to a different type of gas other than default type Indicated on the rating plate at the base of the hob or on the packaging the burner nozzles should be replaced as follows 5 Once the adjustment has been made replace the seals on the by passes using sealing wax or a similar substance If the appliance is connected to liquid gas the regulation screw must be fastened as tightly as possible Once this procedure is finished replace the old rating sticker with one indicating the new type of gas used Stickers are available from any of our Service Centres Should the gas pressure used be different or vary slightly from the recommended pressure a suitable pressure regulator must be fitted to the Inlet pipe in order to comply with current national regulations AIO 77 1 Remove the hob grids and slide the burners off their seats 2 Unscrew the nozzles using a 7 mm socket spanner and replace them with nozzles for the new type of gas see table 1 Burner and nozzle characteristics 3 Reassemble the parts following the above procedure in the reverse order 4 Once this procedure is finished replace the old rating sticker with one indicating the new type of gas used Sticker are available from any of our Service Centres Adjusting the burners primary air DATA PLATE Electrical connections This appliance conforms to the following European Economic Does not require adjusting Setting the burners to minimum 1 Turn the tap to the low flame position 2 Remove the knob and adjust the adjustment screw which is positioned in or next to the tap pin until the flame is small but steady 3 Having adjusted the flame to the required low setting while the burner is alight quickly change the position of the knob from minimum to maximum and vice versa several times checking that the flame does not go out 4 Some appliances have a safety device thermocouple fitted If the device fails to work when the burners are set 4 See data plate Œ Community directives 2006 95 EEC dated 12 12 06 Low Voltage and subsequent amendments 2004 108 EEC dated 15 12 04 Electromagnetic Compatibility and subsequent amendments 93 68 EEC dated 22 07 93 and subsequent amendments 2009 142 EEC dated 30 11 09 Gas and subsequent amendments 2002 96 EC and subsequent amendments

Скачать