Kawai CN27B [11/56] Подготовка инструмента к работе

Kawai CN27W [11/56] Подготовка инструмента к работе
11
11
Preparation Before Use
Setting Up the Piano
1. Connecting the power adaptor
Connect the AC power adaptor to the DC IN terminal located
on the underside of the instrument, as indicated below.
2. Connecting the power adaptor to an outlet
Connect the AC power adaptor to an AC outlet.
3. Turning on the power
Press the POWER switch, located on the right hand side of the
instrument’s front panel.
The LED indicator for the SOUND SELECT button will turn on
and the Concert Grand sound will be selected automatically.
4. Adjusting the volume
Move the MASTER VOLUME slider up and down to increase
and decrease the volume level of the instrument’s speakers, or
headphones if connected.
Adjust the volume to a
comfortable listening level
– the middle is often a good
starting point.
Increase
volume
Decrease
volume
Using headphones
Use the jacks located beneath the keyboard on the left hand
side, to connect stereo headphones to the CN25 digital piano.
Up to two pairs of headphones can be connected and used
simultaneously. When a pair of headphones is connected,
sound will not be produced by the speakers.
Adjusting the pedal support bolt
A pedal support bolt is attached at the base of the pedal board
to aid stability when the pedals are pushed. Turn the bolt anti-
clockwise until it makes contact with the oor and supports
the pedals rmly.
When moving the instrument, always adjust or
remove the pedal support bolt, then readjust
when the instrument is in its new position.
11
Preparation Before Use
Setting Up the Piano
1. Connecting the power adaptor
Connect the AC power adaptor to the DC IN terminal located
on the underside of the instrument, as indicated below.
2. Connecting the power adaptor to an outlet
Connect the AC power adaptor to an AC outlet.
3. Turning on the power
Press the POWER switch, located on the right hand side of the
instrument’s front panel.
The LED indicator for the SOUND SELECT button will turn on
and the SK Concert Grand sound will be selected automatically.
To prevent data loss when turning o the instrument, do
not disconnect the power cable until
is shown in
the LCD display.
4. Adjusting the volume
Move the MASTER VOLUME slider up and down to increase
and decrease the volume level of the instrument’s speakers, or
headphones if connected.
Adjust the volume to a
comfortable listening level
– the middle is often a good
starting point.
Increase
volume
Decrease
volume
Using headphones
Use the jacks located beneath the keyboard on the left hand
side, to connect stereo headphones to the CN27 digital piano.
Up to two pairs of headphones can be connected and used
simultaneously. When a pair of headphones is connected,
sound will not be produced by the speakers.
Adjusting the pedal support bolt
A pedal support bolt is attached at the base of the pedal board
to aid stability when the pedals are pushed. Turn the bolt anti-
clockwise until it makes contact with the oor and supports
the pedals rmly.
When moving the instrument, always adjust or
remove the pedal support bolt, then readjust
when the instrument is in its new position.
Подготовка инструмента к работе
Подготовка к использованию
3. Включение питания 4. Настройка громкости
При перемещении инструмента не забывайте
сначала завернуть поддерживающий винт, а
затем отрегулировать его заново.
1. Подключение адаптера питания
Подсоедините адаптер переменного тока к гнезду DC IN в
нижней части инструмента (см. рис.).
Нажмите кнопку POWER, расположенную справа на передней
панели инструмента.
Загорается светодиод кнопки SOUND SELECT и автоматиче-
ски устанавливается тембр SK Concert Grand.
Во избежание потери данных при выключении инстру-
мента не отсоединяйте кабель питания до тех пор, пока
не появится индикация
на дисплее.
Использование наушников
Для подключения стереофонических наушников к цифрово-
му пианино CN27 воспользуйтесь разъемами, расположен-
ными с левой стороны под клавиатурой.
Одновременно можно подключить и использовать две пары
наушников. Когда подключены наушники, звук на акустические
системы не выводится.
2. Подключение адаптера питания к розетке
Вставьте адаптер переменного тока в сетевую розетку.
Чтобы увеличить или уменьшить уровень громкости звука, вы-
водимого на акустические системы инструмента или подклю-
ченные наушники, перемещайте слайдер MASTER VOLUME вверх
или вниз.
Найдите комфортный для вас
уровень громкости: для на-
чала попробуйте поставить
слайдер на середину шкалы.
Увеличить
громкость
Уменьшить
громкость
Регулировка поддерживающего винта
Этот винт располагается в основании педального механизма
иобеспечивает его стабильность принажатии педалей. Пово-
рачивайте винт против часовой стрелки, пока он не упрется
впол— это обеспечит надежную поддержку педалей.

Содержание

Скачать