Turboair GEA 1M/GRFX/A/60 [11/68] Charcoal filter filter version only
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Turboair GEA 1M/GRFX/A/60 [11/68] Charcoal filter filter version only

Turboair GEA 1M/GRFX/A/60 [11/68] Charcoal filter filter version only
11
To ease the installation, the ring is equipped with an
index G that should correspond to the appropriate guide
H placed on the upper air exit.
11. Complete the installation of the discharge tube.
12. Open the extractable drawer (Fig.6) and apply the
aesthetic Q mask (if supplied) with two screws from the
inside of the hood (Fig, 7).
13. Re-install the grease filters, connect the cooker hood to
the electrical mains and check the perfect operation.
Description of the hood
Fig. 8
1 Control panel
2 Grease filter (1 or 2 depending on the model in
possession)
3 Grease filter release handle
4 Lighting
5 Vapour screen (extractable), according to the model
available, which may be in metal, glass or provided with
grease filter.
6 Aesthetic mask (Available on the basis of the model in
possession).
7 Spacer (Available on the basis of the model in
possession).
8 Wall cabinet (not supplied, the cabinet illustration is
included to explain the type of installation).
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Maintenance
ATTENTION! Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Cleaning the glass vapour screen (available only in some
models)
Fig. 12
The glass be dismounted and cleaned using a normal glass
detergent.
Instructions for removing the glass:
1. Remove the grease filter.
2. Lightly push the glass downwards and allow it slide
forwards.
3. Remove the glass allowing it to rotate slightly.
After cleaning, follow the instructions in reverse to remount the
glass.
Grease filter
This must be cleaned once a month using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle. When washed
in a dishwasher, the grease filter may discolour slightly, but
this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Fig. 9
Charcoal filter (filter version only)
It absorbs unpleasant odours caused by cooking.
2 charcoal filters are required for cooker hoods with 2 motors
and 1 charcoal for cooker hoods with 1 motor.The saturation
of the activated charcoal occurs after more or less prolonged
use, depending on the type of cooking and the regularity of
cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four mounths.
The carbon filter may NOT be washed or regenerated.
Fig. 10
Place the carbon filter in order to cover the protection grill
for the motor fan wheel, then turn the central handle P of
the filter clockwise.
To dismount the central handle P of the filter turn the
handle anti-clockwise.
Replacing lamps
Fig. 11
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
Access the lamp housing area:
remove the lamp holder using a small screwdriver or
similar tool as a lever.
Replace the damaged light bulb.
Use only 40W max (E14) olive shape light bulbs.
Then close the lamp housing (snap lock).
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.

Содержание

Похожие устройства

Скачать