Home
Главная
Bort
Пылесосы
BSS-1800N-ECO
Инструкция по эксплуатации Страница: 7

Bort BSS-1800N-ECO [7/24] Assembly instructions

Vacuum Cleaner

DEAR CUSTOMER!

Congratulations on the purchase of BORT product,

which has progressive design and high quality. We

hope that our products will be your companion for

many years.

For the efﬁ cient and safe use of the product, please

read this manual and save it for future reference.

SPECIFICATIONS 1

MAINTENANCE INSTRUCTIONS 2

1. Handle

2. 2-in-1 Tool

3. Air Escape Pushbutton

4. crevice Tool

5. Hose

6. Release Button

7. Telescopic Tube

8. Floor brush

9. Handle Of Dust

10. Release Button Of Dust

11. Cyclone dust container

12. Switch Pedal

13. Tube Support

14. Power plug

15. Cord reeling pedal

ATTENTION: All schematic pictures may differ from the

actual product

COMPLETE SET

Standard complete set of the product includes:

Vacuum Cleaner

Hose

Telescopic tube

Crevice nozzle

Multi brush

Brush for upholstery and carpets

Owner’s manual

Due to the constant improvement of the technical

characteristics of the models, we reserve the right to

make changes in construction and/or complete set of

product.

SAFETY AND SECURITY

1.Be sure to use the cleaner in compliance with the

contents of this manual, and use the ﬁ ttings designated

by the manufacturer.

2. Please do not leave the cleaner when it is powered

on. Turn off the power switch and pull out the power

plug when not using or before maintenance.

3. Please do not pull or carry the cleaner by the power

cord, or nip it when closing a door; keep the cord free

from the press of the cleaner.

4. Please do not let children take the cleaner as a toy,

and close attention is necessary when the cleaner ap-

proaches children.

5. Please do not use the cleaner when its power cord or

plug is damaged. Send it to the appointed service cent-

er. Please do not unplug by pulling the cord or plug. To

unplug, grasp the plug, not the cord.

6. Never pull the power plug or use the cleaner with

wet hands.

7. When using the cleaner, pay attention to prevent any

hair roll or other rubbish block up the air inlet (includ-

ing the hose and the spile), otherwise motor failure and

housing distortion may be caused. If the matters ab-

sorbed in forms a blockage, stop the cleaner by pulling

out the power plug immediately to clean the blockage.

8. When using the cleaner, don’t plug up the air outlet

by towel or other matters, otherwise the efﬁ ciency of

dust absorbance will be inﬂ uenced, and the motor will

be at high risk of being burnt out.

9. Never use the cleaner at uneven ﬂ oor or ground;

and be very careful when cleaning stairs to prevent the

cleaner from falling down.

10. Never absorb live stumps with the cleaner, other-

wise the motor may be damaged.

11. The cleaner should be kept far away from heat

sources (such as central heating, oven, etc) to avoid

the distortion of plastic parts as well as the inﬂ uence

caused by such distortion.

12. Before using the cleaner, please remove big and

sharp matters on the ﬂ oor to avoid damaging the plas-

tic parts, ﬁ lter gauzes and motor.

13. Never absorb water or other liquid with this cleaner,

otherwise, the motor will be damaged.

14. This appliance is not intended for use by persons

(including children), with reduced physical, sensory or

mental capabilities, or lack of experience and knowl-

edge, unless they have been given supervision or in-

struction concerning use of the appliance by a person

responsible for their safety.

ASSEMBLY INSTRUCTIONS

1. Before assembling the cleaner, please conﬁ rm all

parts and components for the cleaner are received by

referring to Parts and Components List.

2. Please remember to cut off the power supply before

assembly.

ASSEMBLY OF HOSE

1. As is shown in Figure (3), insert the hose into the

duct inlet of the machine body in horizontal direction.

Please pay attention to the alignment of two projecting

parts. Turn the hose right when it is pushed into the

bottom, a click of inserting sound may be heard, i.e. the

hose is assembled into the machine body completely.

2. ASSEMBLY AND REMOVAL OF DUST

BARREL

As is shown in Figure (4), place the bottom of the dust

barrel on the projecting part at the front end of the

machine body, and press down the dust barrel. When

the front-end hook is entered into the corresponding

part of the machine body completely, and a click of

inserting sound is heard, which indicate that the dust

barrel is assembled in place. To remove the dust barrel,

press down the handle of the dust barrel; when the

Bort BSS-1800N-ECO [7/24] Assembly instructions

Содержание

Похожие устройства