Timberk TFH W200.XS [3/9] Illlllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll...

Illllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllllll 7 Installation of the unit TFH W200 XB Panel Remote controller for W200 TR W200 AD IW200 NN models Mounting of the unit is carried out in the following order Mark a true horizontal line on a vertical smooth wall at the height not less than 1 8mfrom the floor Plot two marks for designed holes along the indicated line with the distance between them equal to either 57 cm or 65 cm for W250 RL I W250 ZM models Take into account that upon mounting of the unit its overall dimensionswill be larger than the distance between the marks It is recommended to leave a free space within 20 cm and more towards both sides away from plotted marks Drill holes in the wall strictly according to the marks and fit in a plastic dowel supplied with the unit Then tighten a mounting screw into the dowel Make sure that the mounting screws are secured properly and mount the heateronthem TIMER buttonpress this button to switch on the operating timer and select its working period OSCIL buttonpress this button to activate the automatic heat flow direction control mode Press this button again to deactivate this mode MODE buttonpress this button to select heat flow modes Button press this button to switch on the unit press this button again to switch off the unit case of the remote controller Remote controller for W200 XB W200 XS models indicator panel 1 This symbol same as ON OFF function 2 1000W is lower heating 3 2000w is higher heating 4 Timer is the same as the timer on the panel Air ouput TFH W200 XS Panel 8 Unit operation indicator panel Air ouput 6 Scope of delivery The fan heater is equipped with a positional power mode rated power W for W250RX W250ZM models cold air flow warm air flow hotair flow 0 0 1000 1250 2000 2500 Prior to use of the unit please read this manual carefully pFM n Í TT l i F i i í T i 1 Fan heater 1 pc 2 Support 1 pc 3 Plastic nut 1 pc 4 Remote controller 1 pc 5 Operation manual 1 pc 6 Guarantee card 1 pc 7 Package 1 pc 8 Screws 2 pcs O IMPORTANT Prior to switching on the unit make sure that the air outlet is not blocked by any objects i lF F TTTTTÍTFTTF iFFTTHTTin FTTF níTTTTFTFF FJIFTÍITTTT i F F I FÎT i F 111 F I i T j II IFF IMPORTANT The manufacturer can alter the appearance of the remote controller without prior notification of the userto introduce modifications and improve its external design After switching off the unit will operate in the fan only mode to cool down heating elements for about 30 seconds Then the fan heater will be switched off ENGLISH lllll Unit control by means of the remote controller fforW200 TR W200 AD W200 NN models 1 Connect the unit s power cord to a grounded European standard outlet Do not use the unit on uneven and unstable surfaces nearby combustible flammable or easily deformable objects 2 To switch on the unit press button after that an indicator light will illuminate pn the control panel indicating the activate fan mode Press button O again to switch off the heater 3 Select a comfortable heating mode by setting the desired heat flow To do so press MODE button as many times as necessary to activate the selected heat flow mode 1000W and 2000W buttons on the W200 XB W200 XS series Indicator lights on the control panel of the unit will display the modes you select 4 If it is necessary to set the automatic mode of the air louver control press SWING button on the remote controller A SWING LED will illuminate Louvers will start swinging smoothly changing the air flow direction and uniformly distributing heat in the room 5 This heater is equipped with a built in 7 5 hour timer function the remote controller The timer sets time for operation of the unit By sequential pressing of TIMER button you select the time of its operation upon that indicator lights illuminate respectively 0 5h 1 h 1 5h 2h 2 5h 3h 3 5h 4h 4 5h 5h 5 5h 6h 6 5h 7h 7 5h Unit control by means of the control panel for W200 TR W200 AD W200 NN models 1 Connect the unit s power cord to a grounded European standard outlet Do not use the unit on uneven and unstable surfaces nearby combustible flammable or easily deformable objects 2 To switch on the unit press button O after that an indicator light will illuminate on the control panel indicating the activate fan mode 3 Select a comfortable heating mode by setting the desired heat flow To do so press button O as many times as necessary to activate the selected heat flow mode Indicator lights on the control panel of the unit will display the modes you select including the automatic air louver control mode SWING LED illuminates Pressing button O several times depending on the current mode will switch off the unit and a green LED will be flashing upon that 4 To activate the built in timer function use TIMER button The timer sets time for operation of the unit By sequential pressing of TIMER button you select the time of its operation upon that indicator lights illuminate respectively 0 5h 1 h 1 5h 2h 2 5h 3h 3 5h 4h 4 5h 5h 5 5h 6h 6 5h 7h 7 5h I____________________________________ _________________________________________ I Such options is missing in W200 XS W200 XB series 4 www timberk com electric metal ceramic fan heater www timberk com electric metal ceramic fan heater 5