![Icom IC-F621 [21/24] I antenna](/img/pdf.png)
Icom IC-F621 [21/24] I antenna
![Icom IC-F621 [21/24] I antenna](/views2/1074569/page21/bg15.png)
18
4
CONNECTION AND MAINTENANCE
■ Antenna
A key element in the performance of any communication sys-
tem is an antenna. Ask your Dealer about antennas and the
best places to mount them.
■ Fuse replacement
Two fuses are installed in the supplied DC power cable. If a
fuse blows or the transceiver stops functioning, track down
the source of the problem, if possible, and replace the dam-
aged fuse with a new rated one.
❑ Fuse rating : 15 A,
■ Cleaning
If the transceiver becomes dusty or dirty, wipe it clean with a
dry, soft cloth.
AVOID the use of solvents such as benzene or alco-
hol, as they may damage transceiver surfaces.
q
LCD backlit cont. IN
w AF OUT
e Det. AF OUT
r Mod. IN
t PTT control IN
y Horn drive cont. OUT
u AF GND
i Det. AF GND
o Mod. GND
OPTIONAL CABLE PIN ASSIGNMENT
t r e w q
o i u y
■ Optional OPC-617 installation
Install the OPC-617 as shown below.
IC-F510F520_F610F620-1.qxd 02.3.12 2:51 PM Page u (1,1)
Содержание
- Cautions 2
- Explicit definitions 2
- Important 2
- R warning neve 2
- Read all instruction 2
- Save this instruction manual 2
- Be careful 3
- For u s a only caution changes or modifications to this transceiver not expressly approved by icom inc could void your authority to operate this transceiver under fcc regulations 3
- Operating the transceiver without running the vehi cle s engine the vehicle s battery will quickly run out if the transceiver is in transmission while the vehicle s engine off 3
- Peratures below 22 f 30 c or above 140 f 60 c or in areas subject to direct sunlight such as the dashboard 3
- Placing the transceiver against walls this will obstruct heat dissipation 3
- Placing the transceiver in excessively dusty envi ronments 3
- Table of contents 3
- The transceiver will become hot when operating continuously for long periods 3
- The use of chemical agents such as benzine or alcohol when cleaning as they damage the transceiver sur faces 3
- I front panel 4
- Panel description 4
- I function display 5
- Panel description 5
- I programmable function keys 6
- Panel description 6
- Panel description 7
- Panel description 8
- Panel description 9
- I channel selection 10
- I turning power on 10
- Operation 10
- D transmitting notes 11
- I receiving and transmitting 11
- Important 11
- Operation 11
- D dtmf transmission 12
- D scrambler function 12
- D tx code channel selection 12
- D tx code number selection 12
- Operation 12
- D user set mode 13
- Operation 13
- D calling another local system subscriber 14
- D placing a telephone call 14
- D receiving a call 14
- I smartrunk ii and conventional modes 14
- I smartrunk ii operation 14
- Optional smartrunk ii operation 14
- D clear channel alerting 15
- D emergency call 15
- D last number re dial 15
- D memory speed dialling 15
- D programming memory speed dial 15
- D ptt dispatch operation 15
- D system busy indication 15
- D terminating a call 15
- D turbo speedial 15
- Optional smartrunk ii operation 15
- Connection and maintenance 16
- I rear panel and connection 16
- Connection and maintenance 17
- I supplied accessories 17
- Connection and maintenance 18
- D inverting the front panel 18
- I mounting the transceiver 18
- Connection and maintenance 19
- D mounting the transceiver 19
- Connection and maintenance 20
- I optional ut 105 and ut 108 installation 20
- I optional ut 109 ut 110 installation 20
- A key element in the performance of any communication sys tem is an antenna ask your dealer about antennas and the best places to mount them 21
- Avoid the use of solvents such as benzene or alco hol as they may damage transceiver surfaces 21
- Connection and maintenance 21
- I antenna 21
- I cleaning 21
- I fuse replacement 21
- I optional opc 617 installation 21
- If the transceiver becomes dusty or dirty wipe it clean with a dry soft cloth 21
- Install the opc 617 as shown below 21
- Two fuses are installed in the supplied dc power cable if a fuse blows or the transceiver stops functioning track down the source of the problem if possible and replace the dam aged fuse with a new rated one 21
- Options 22
- Electromagnetic interference compatibility 23
- Safety training information 23
- 1 32 kamiminami hirano ku osaka 547 0003 japan 24
- Count on us 24
Похожие устройства
- Zanussi ZAN2415 Инструкция по эксплуатации
- Ardo KA 631 EB Инструкция по эксплуатации
- Icom IC-F1020 Инструкция по эксплуатации
- Ardo KA 531 EB Инструкция по эксплуатации
- Icom IC-F2020 Инструкция по эксплуатации
- Samsung SC-61B3H3A Инструкция по эксплуатации
- Ardo DW 45 E Инструкция по эксплуатации
- Icom IC-F1500 Инструкция по эксплуатации
- Samsung SC-61B5H3K Инструкция по эксплуатации
- Ardo DW 45 AEL Инструкция по эксплуатации
- Icom IC-F2500 Инструкция по эксплуатации
- Samsung SC-9670H3G Инструкция по эксплуатации
- Ardo DW 45 AL Инструкция по эксплуатации
- Icom IC-F3061 Инструкция по эксплуатации
- Samsung SD-9450S3B Инструкция по эксплуатации
- Ardo DWF09L6W Инструкция по эксплуатации
- Icom IC-F4061 Инструкция по эксплуатации
- Bissell 23B6J Инструкция по эксплуатации
- Ardo DWF09L5W Инструкция по эксплуатации
- Icom IC-F21GM Инструкция по эксплуатации