![Icom IC-F21GM [17/32] Charging note](/img/pdf.png)
Icom IC-F21GM [17/32] Charging note
![Icom IC-F21GM [17/32] Charging note](/views2/1074605/page17/bg11.png)
10
3
BATTERY PACKS
‘‘
Charging NOTE
Prior to using the transceiver for the first time, the battery pack must
be fully charged for optimum life and operation.
• Recommended temperature range for charging:
+10°C to +40°C (50°F to 140°F).
• Use the supplied charger or optional charger (BC-119/BC-121/BC-
144 for rapid charging, BC-146 for regular charging) only. NEVER
use other manufacturers’ chargers.
The optional BP-209, BP-210 or BP-222 battery packs include
rechargeable Ni-Cd(Ni-MH: BP-210) batteries and can be charged
approx. 300 times. Charge the battery pack before first operating
the transceiver or when the battery pack becomes exhausted.
If you want to charge the battery pack more than 300 times, the fol-
lowing points should be observed:
• Avoid overcharging–batteries must be removed from the charger
to stop charging. Batteries should not be charged for more than
15 hours after the LED indicator turns green.
• Use the battery until it becomes almost completely exhausted
under normal conditions.
DD
Battery pack life
When the operating period becomes extremely short even after
charging the battery pack fully, a new battery pack is needed.
NOTE: The charger rapidly charges a battery pack to a speci-
fied level, not a completed level, to prevent overcharging. Leave
the battery pack in the charger for a few more hours (up to
15 hours; depending on battery condition) after the LED indica-
tor turns green, to charge the battery completely.
Содержание
- If21gm 1
- Instruction manual 1
- Uhf gmrs transceiver 1
- Safety training information 2
- During transmissions your icom radio generates rf energy that can possibly cause interference with other devices or systems to avoid such interference turn off the radio in areas where signs are posted to do so do not operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals aircraft and blasting sites 3
- Electromagnetic interference compatibility 3
- General mobile radio service gmrs 4
- Foreword 6
- Important 6
- Table of contents 7
- Panel description 8
- Switches controls keys and connectors 8
- Auto scan led blinks during scan operation p 22 10
- Caution low batt3 if you did not charge the battery after low batt2 warning has appeared the low batt3 warning beep emits for 15 sec then the power turns off automatically 10
- Led indicator 10
- Low batt1 you should charge the battery blinks slowly 10
- Low batt2 you must charge the battery blinks fast 10
- Rx turns green while receiving a signal 10
- The tx rx indicator led indicates informa tion in several ways as follows ref r red g green 10
- Tx low batt1 low batt1 was detected during tx mode 10
- Tx low batt2 low batt2 was detected during tx mode 10
- Tx turns red while transmitting a signal 10
- Accessories 11
- Accessory attachment 11
- Battery pack replacement 12
- Battery packs 12
- Battery cautions 13
- Battery charging 14
- Check orientation and the spacer com bination as follows 15
- Charging note 17
- Note the charger rapidly charges a battery pack to a speci fied level not a completed level to prevent overcharging leave the battery pack in the charger for a few more hours up to 15 hours depending on battery condition after the led indica tor turns green to charge the battery completely 17
- Battery case option 18
- Set mode 19
- Frequency channel list 21
- Ctcss tone code list 23
- Ctcss confirmation beep 24
- 0 push moni to complete the setting 25
- 0 push ptt once more if you want to use inverse mode 1 push moni to complete the setting 25
- 1 turn the power off and then on again 25
- 2 turn the power off and then on again 25
- Dtcs code list 25
- Example to assign code 261 normal as ch12 25
- I push ptt once to choose the 1 digit of the code number o push moni 25
- Q while pushing and holding ptt moni w n turn off vol to power on w select ch 12 e push and hold w n until a beep pi is emitted r push ptt twice to choose the 100 digit of the code number t push moni 25
- Y push ptt six times to choose the 10 digit of the code number u push moni 25
- Operation 27
- Receiving and transmitting 27
- Auto scan function 29
- Setting squelch level 29
- Wide narrow selection 29
- Option 30
- Options 30
- Count on us 32
Похожие устройства
- Philips GC 4420/02 Инструкция по эксплуатации
- Ardo DWF09S4W Инструкция по эксплуатации
- Icom IC-M1 Инструкция по эксплуатации
- Bimatek IR400 Инструкция по эксплуатации
- Brother DS-140 Инструкция по эксплуатации
- Icom IC-M1V Инструкция по эксплуатации
- Bimatek IR401 Инструкция по эксплуатации
- Brother Innov-is 20 Инструкция по эксплуатации
- Icom IC-M3A Инструкция по эксплуатации
- Bimatek IR300 Инструкция по эксплуатации
- Icom IC-M2A Инструкция по эксплуатации
- Bimatek IR301 Инструкция по эксплуатации
- Icom IC-M34 Инструкция по эксплуатации
- Liebherr KBs 3864-20 Инструкция по эксплуатации
- Icom IC-M15 Инструкция по эксплуатации
- Liebherr CTsl 2451-20 Инструкция по эксплуатации
- Icom IC-M45A Инструкция по эксплуатации
- Bosch KGV36VW20R Инструкция по эксплуатации
- Icom IC-M56 Инструкция по эксплуатации
- Hotpoint-Ariston ECF 2014 L Инструкция по эксплуатации
Скачать
Случайные обсуждения