![Daikin FTXV50AV1B [32/40] Malfunction analysis](/img/pdf.png)
Daikin FTXV50AV1B [32/40] Malfunction analysis
![Daikin RXV35AV1B [32/40] Malfunction analysis](/views2/1772007/page32/bg20.png)
29
Malfunction analysis
Phenomenon Check items Solution
Air conditioner
can’t operate
● Power failure? ● Wait until power recovery.
● Air switch trips off or fuse is
burnt out?
● Ask professional to replace
air switch or fuse.
● Wiring has malfunction? ● Ask professional to replace it.
● Unit has restarted
immediately after stopping
operation?
● Wait for 3min, and then turn
on the unit again.
● Whether the function setting
for remote controller is
correct?
● Reset the function.
Mist is emitted
from indoor
unit’s air outlet
● Indoor temperature and
humidity is high?
● Because indoor air is cooled
rapidly. After a while, indoor
temperature and humidity will
decrease and mist will
disappear.
Set
temperature
can’t be
adjusted
● Unit is operating under auto
or save mode?
● Temperature can’t be
adjusted under auto and save
modes. Please switch the
operation mode if you need to
adjust temperature.
● Your required temperature
exceeds the set temperature
range?
● Set temperature range:
16°C~30°C .
Cooling
(heating)
effect is
not good.
● Voltage is too low?
● Wait until the voltage
resumes to normal.
● Filter is dirty? ● Clean the filter.
● Set temperature is in proper
range?
● Adjust temperature to proper
range.
● Door and window are open? ● Close door and window.
Содержание
- Owner s manual 1
- Attachment 3
- Content 3
- Installation 3
- Installation notice 3
- Maintenance 3
- Malfunction 3
- Operation notices 3
- Screen operation guide 3
- Test and operation 3
- Safety precautions 4
- Warning 4
- Caution 5
- Indoor side db wb c outdoor side db wb c maximum cooling 32 23 43 26 maximum heating 27 24 18 5
- The operating temperature range outdoor temperature is 18 43 c for cooling and 10 24 c for heating operation 5
- Working temperature range 5
- Indoor unit 6
- Outdoor unit 6
- Parts name 6
- At least 50cm 7
- Installation dimension diagram 7
- Space to the obstruction 7
- Selection of installation location 8
- Tools for installation 8
- Grounding requirement 9
- Requirements for electric connection 9
- Safety precaution 9
- And 35 class 10
- Choose the position of piping hole according to the direction of outlet pipe the position of piping hole should be a little lower than the wall mounted frame shown as below 10
- Hang the wall mounting frame on the wall adjust it in horizontal position with the level meter and then point out the screws fixing holes on the wall 2 drill the screw fixing holes on the wall with impact drill the specification of drill head should be the same as the plastic expansion particle and then fill the plastic expansion particles in the holes 3 fix the wall mounting frame on the wall with tapping screws st4 x25ta and then check if the frame is firmly installed by pulling the frame if the plastic expansion particle is loose please drill another fixing hole nearby 10
- Installation of indoor unit 10
- Open a piping hole with the diameter of ø55 or ø70 on the selected outlet pipe position in order to drain smoothly slant the piping hole on the wall slightly downward to the outdoor side with the gradient of 5 10 10
- Recommend the installation location to the client and then confirm it with the client 10
- Step one choosing installation location 10
- Step three open piping hole 10
- Step two install wall mounting frame 10
- Installation of indoor unit 11
- Step five connect the pipe of indoor unit 11
- Step four outlet pipe 11
- Ø55 ø70 11
- Installation of indoor unit 12
- Step seven connect wire of indoor unit 12
- Step six install drain hose 12
- Installation of indoor unit 13
- Installation of indoor unit 14
- Step eight bind up pipe 14
- Step nine hang the indoor unit 14
- Installation of outdoor unit 15
- Step one fix the support of outdoor unit select it according to the actual installation situation 15
- Step three fix outdoor unit 15
- Step two install drain joint only for cooling and heating unit 15
- Installation of outdoor unit 16
- Step five connect outdoor electric wire 16
- Step four connect indoor and outdoor pipes 16
- Installation of outdoor unit 17
- Step six neaten the pipes 17
- Leakage detection 18
- Use vacuum pump 18
- Vacuum pumping 18
- Check after installation 19
- Items to be checked possible malfunction 19
- Method of test operation 19
- Preparation of test operation 19
- Test operation 19
- Configuration of connection pipe 20
- Pipe expanding method 21
- Button 22
- Buttons on remote controller 22
- Fan button 22
- Introduction to icons on display screen 22
- Light button 22
- Mode button 22
- On off button 22
- Save button 22
- Sleep button 22
- Swing button 22
- Timer button 22
- Turbo button 22
- X fan button 22
- Introduction to buttons on remote controller 23
- Introduction to buttons on remote controller 24
- Introduction to buttons on remote controller 25
- Child lock function 26
- Introduction to buttons on remote controller 26
- Introduction to functions of combination buttons 26
- Switchover function for temperature display 26
- Operation guide 27
- Replacement of batteries in remote controller 27
- Clean surface of indoor unit 28
- Cleaning and maintenance 28
- Emergency operation 28
- Clean filter 29
- Cleaning and maintenance 29
- Install filter 29
- Open panel 29
- Remove filter 29
- Checking after active season 30
- Checking before active season 30
- Cleaning and maintenance 30
- Notice for recovery 30
- General phenomenon analysis 31
- Malfunction analysis 31
- Malfunction analysis 32
- Malfunction analysis 33
- Malfunction 34
- Malfunction analysis 34
- Warning 34
- Do not turn on the safety breaker until all work is completed 1 for both outdoor and indoor units strip the insulation from the wire 40mm 2 connect the connection wires between the indoor and outdoor units so that the terminal numbers match tighten the terminal screws securely we recommend a flathead screw driver be used to tighten the screws 3 for connecting outdoor unit to indoor unit use standardized supply cable h05rn 35
- Wiring 35
- Wiring 36
- Wiring diagram 36
- Disposal requirements 37
- Environmental information 37
- Extra refrigerant charge 37
- Instruction appendix 37
- Copyright 2013 daikin 40
Похожие устройства
- Daikin FTXV60AV1B Инструкция по монтажу
- Daikin FVXM25A2V1B Инструкция по эксплуатации
- Daikin FVXM25A2V1B Инструкция по монтажу
- Daikin FVXM25A2V1B Справочник установщика
- Daikin FVXM35A2V1B Инструкция по эксплуатации
- Daikin FVXM35A2V1B Инструкция по монтажу
- Daikin FVXM35A2V1B Справочник установщика
- Daikin FVXM50A2V1B Инструкция по эксплуатации
- Daikin FVXM50A2V1B Инструкция по монтажу
- Daikin FVXM50A2V1B Справочник установщика
- Daikin FWXV15AVEB Инструкция по монтажу
- Daikin FWXV15AVEB Руководство по установке
- Daikin FWXV15AVEB Приложение к руководству для дополнительного оборудования
- Daikin FWXV15AVEB Инструкция по эксплуатации
- Daikin FWXV20AVEB Инструкция по монтажу
- Daikin FWXV20AVEB Руководство по установке
- Daikin FWXV20AVEB Приложение к руководству для дополнительного оборудования
- Daikin FWXV20AVEB Инструкция по эксплуатации
- Daikin MC55WVM Инструкция по эксплуатации
- Daikin MC70LVM Инструкция по эксплуатации