P.I.T. PSB13-C5 [2/21] Impact drill
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

P.I.T. PSB13-C5 [2/21] Impact drill

P.I.T. PSB13-C5 [2/21] Impact drill
GENERAL SAFETY PRECAUTIONS
1. Always keep the workplace clean. Contaminated workplace and workbenches increase the risk of accidents.
2. Follow the operation manual carefully. Do not use the tool when it rains. Also do not use the tool in damp
locations. The workplace should be well-lit. Do not use the tool near flammable liquids or gas. During operation, as
well as power on and power off, the tool generates sparks. Therefore, never use the tool in places where there are
varnishes, paints, gasoline, dissolvers, gas, adhesives and other flammable and explosive materials.
3. To prevent electric shock during operation, make sure that the drill case is not in contact with grounded objects,
for example, when laying pipes, when installing heating batteries, plates, refrigerators, etc.
4. Keep children away from the electric tool while it is operating. Keep unauthorized persons away from the electric
tool and power extender.
5. Store the tool in a dry and lockable place so that it does not fall into the hands of children or unauthorized
persons.
6. Use the tool without pressure and applying force. The drill will work better and more reliably if you use the
recommended speeds by the operation manual.
7. Use only those types of tools that directly comply with the requirements of this type of work. For jobs requiring a
high power tool, you cannot use a tool with a lower power. It is recommended to use tools suitable for the applica-
tion purposes, for example, do not use a circular saw in order to saw down knots or trees.
8. During work, wear comfortable and suitable clothing. Do not also wear jewelry during operation. Loose parts of
clothing or jewelry can be tightened by moving parts of the tool. During work on the street, rubber gloves and
comfortable shoes with lug sole should be worn on so that the sole does not slip.
9. If a large amount of dust forms during operation, wear safety goggles and an anti-powder mask.
10. Handle the cable with care. When unplugging, do not pull the cable. Do not leave the cable in the heat, on the
oil surface or on the surface with sharp edges.
11. Secure the workpiece securely. Use clamps and jaw vices if possible to secure the part. This is more reliable
than holding the part.
12. Do not tilt the tool too much. Always maintain a stable position and a good balance.
13. Watch closely for the tool conditions. For better and more reliable use, they must always be sharp and clean.
Follow the operation manual for lubricating and replacing the accessories. Regularly check the tool cable condition
and, if damaged, return it to the technical service centers for repairs. From time to time, check the power extender
and replace it if damaged. Keep handles in a dry, clean place; do not allow oil and grease to enter the handles.
14. Disconnect tool from the mains, when not in use, and do not power on them during servicing or replacing
accessories, such as a circular saw blade, drill bit, blade, etc.
15. Always check before power on the tool that the adjusting wrench and the wrench are removed.
16. Avoid involuntary power on the tool. Do not hold the connected tool by the switch. Before attaching, make sure
that the tool is disconnected.
17. When working outdoors, use an appropriate power extender. Use only a power extender fits the wire cross-sec-
tion.
18. Always keep the work process under control. Do not use tool if you are tired.
19. Inspect damaged parts carefully. Before further use of the tool, carefully check that the tool functions properly
and if all the prescribed functions are performed by the tool. Also check the installation and fastening of moving
parts, watch for parts breakage and other conditions that can adversely affect the operation of the tool. Damaged
parts and protective equipment must be exchanged only in technical service centers. Defective switches are also
exchanged in these centers. Do not use the tool if it cannot be powered on or off by the switch.
20. Use electric tools only for the purpose intended in the operation manual.
21. Using of the accessory components that are not listed in the operation manual or in the catalog may cause the
tool damage.
22. Repair the tool only in special technical service centers. The manufacturer is not liable for damage or damage
caused to the tool as a result of repair by persons who do not have special authority for this or as a result of
careless handling of the tool.
23. In order to ensure the production integrity of the tool, never remove the built-in cases or bolts.
24. Do not touch the moving parts and accessories if the tool is not powered off.
25. Use a tool with low power consumption as indicated on the type plate of the tool, otherwise, due to overload,
the quality of the surface to be treated, and consequently the efficiency, can be significantly reduced.
26. Do not wipe the plastic parts with solvent. Solvents such as gasoline, solvent, carbon tetrachloride, alcohol,
ammonia and oil can damage the plastic material or cause cracks. When cleaning plastic parts, use soapy water
and a wash-cloth.
27. Use only original replacement parts.
28. A detailed diagram of the elements in the operation manual is provided only for technical service centers.
1
impact drill

Содержание

Похожие устройства

Скачать