Home
Главная
Flex
Лобзик
JS 18.0-EC
Инструкция по эксплуатации Страница: 16

Flex JS 18.0-EC [16/176] Adapting board adapting board

JS 18.0-EC /

JSB 18.0-EC

Adjusting the Foot Bevel AngleAdjusting the Foot Bevel Angle

Remove the hexagon wrench from the foot

(see 󰘰gure G).

To adjust the cutting angle

Turn the tool upside down.

Loosen the hex screw that secures the

foot by the hexagon wrench.

Move the foot slightly forward and tilt it to

the required angle (0° or 45° ) using the

scale (0° or 45° ) that is marked on the

base bracket.

The foot has indents at 0° and 45° (tilt left or

right) for easy angle setting. (see 󰘰gure H).

Installing and disassembling of Installing and disassembling of

accessoriesaccessories

CAUTION!CAUTION!

Use the cover plate when cutting decorative

veneers, plastics, etc. It protects sensitive or

delicate surfaces from damage. Fit it on the

back of the tool base

Cover plateCover plate

Installation:

First, the front part of the plate cover is

snapped into the plate. (see 󰘰gure I)

Then the rear cover of the cover is aligned

and then snapped in.（see 󰘰gure J）

Disassembly:

Firstly, the two card positions on the

back of the plate cover are removed (see

󰘰gure K)

Then the bottom plate is turned down.

After about 30° , the front card position

can be removed (see 󰘰gure L).

Adapting boardAdapting board

Installation:

Insert the adapting board from the front of

the foot about a distance along the slot (a

certain distance from the saw blade).

When using the adapting board for the

󰘰rst time, insert the saw blade and switch

on, align the foot surface, push the

adapting board, and insert the adapting

board along the slot (see Figure M) while

the saw blade is sawed in the middle of

the adapting board.

A slit makes the adapting board and the

saw blade 󰘰t properly to improve the

cutting quality (see Figure N).

When the adapting board is inserted,

there are two limit positions, which

correspond to di󰘯erent card positions and

adapt to di󰘯erent needs and improve the

service life.

Disassembly:

When the machine is o󰘯, remove the

saw blade and pull out the adapting board

directly (see Figure O).

Transparent CoverTransparent Cover

Installation: Insert the transparent cover from

the front of the machine, snap the gearbox,

and the limit post is aligned with the gearbox

positioning groove. (see 󰘰gure P).

Disassembly: Open the buckle (see 󰘰gure Q),

and remove the transparent cover forward.

Vacuum tubeVacuum tube

Installation:

Let the front of vacuum tube toward the

saw blade, insert the middle snap into the

slot on the bottom of the foot (see 󰘰gure R),

Push the vacuum tube backward, and

align the front screw with the screw hole

on the foot, screw the vacuum tube (see

󰘰gure S).

The vacuum tube can be mounted

on either side of the right or left to

accommodate cutting at di󰘯erent angles

of the foot.

Disassembly:

Loosen the screw and push the vacuum

tube slightly forward to remove it directly.

Switching on and o󰘯Switching on and o󰘯

JS 18.0-EC:

Switching on: push the switch button

forwards and release.

Switching o󰘯：push the switch button

forwards and release.

The left and right switch buttons function

are the same.

JSB 18.0-EC:

Lock-o󰘯：Lock button to the far left. The

on/o󰘯 switch is locked and cannot be

pressed. (see 󰘰gure T1).

On: Lock button moves to the middle

so you can see it on the left and right.

Now the on/o󰘯 switch can be pressed to

accelerate the machine. (see 󰘰gure T2).

Lock-on：With on/o󰘯 switch fully pressed

in and the lock button pushed to the far

right, the on/o󰘯 switch can be locked to

the “on” position. Press the on/o󰘯 switch

again to release the lock(see 󰘰gure T3).

Flex JS 18.0-EC [16/176] Adapting board adapting board

Содержание

Похожие устройства