![Daikin ATKS35BVMB [9/14] _en_2p098777 1 fm page 8 friday october 18 2002 1 26 pm](/img/pdf.png)
Daikin ATKS35BVMB [9/14] _en_2p098777 1 fm page 8 friday october 18 2002 1 26 pm
![Daikin ATX35BVMB [9/14] _en_2p098777 1 fm page 8 friday october 18 2002 1 26 pm](/views2/1778712/page9/bg9.png)
■English 8
Note:
1) Wrap the refrigerant pipes and drain hose together with insulation tape as
right figure, in case of setting the drain hose through the back of the indoor
unit.
2) If it difficult to fix the claws of the bottom frame on the catches of the
mounting plate.
Secure indoor unit to the mounting plate with scres (M4 × 12L).
3-3. Wall Embedded Piping
Follow the instructions given under
1) Insert the drain hose to this depth so it wont be pulled out of the drain
pipe.
4.
Wiring.
, install as described in the installation manual supplied with the Multi outdoor unit.
1) Strip wire ends (15 mm).
2) Match wire colours with terminal numbers on indoor and outdoor unit’s terminal blocks and firmly screw wires to the corre-
sponding terminals.
3) Connect the earth wires to the corresponding terminals.
4) Pull wires to make sure that they are securely latched up, then retain wires with wire retainer.
5) Shape the wires so that the service lid fits securely, then close service lid.
■
■■
■
Warning
Do not use tapped wires, stand wires, extensioncords, or starbust connections, as they may cause overtheating, electrical
shock,or fire.
Left-Side, Left-Back, or Left Bottom Piping
Refrigerant
pipes
Drain hose
Bottom frame
H M4 × 12L (2 point)
Mounting
plate
A
Inner wall
Vinyl chloride
drain pipe
(VP-30)
Drain hose50 mm
or more
Insert drain hose
to this depth so
it won
’t be pulled
out of drain pipe.
Outer wall
With a Multi indoor unit
123
Terminal block
Electrical component box
Wire retainer
Use the specified wire type.
Firmly secure wire retainer so that
wires sustain no external stress.
Shape wires so that the
service lid will fit securely.
1
2
3
123 LN
Safety
breaker
15A
Earth leakage
circuit breaker
Earth
When wire length exceeds
10 m, use 2.0-mm wires.
H05VV
Firmly fix the wires with
the terminal screws.
Outdoor unit
Indoor
unit
Power
supply
50Hz 220V - 240V
60Hz 220V - 230V
Firmly fix the wires with
the terminal screws.
01_EN_2P098777-1.fm Page 8 Friday, October 18, 2002 1:26 PM
Содержание
- Ftxs25bvmb ftks25bvmb ftxs35bvmb ftks35bvmb ftx25bvmb ftk25bvmb ftx35bvmb ftk35bvmb atxs25bvmb atks25bvmb atxs35bvmb atks35bvmb atx25bvmb atk25bvmb atx35bvmb atk35bvmb 1
- Installation manual 1
- Models 1
- R 410a split series 1
- Cautions 2
- I english 2
- Safety precautions 2
- Warnings 2
- Accessories 3
- Choosing a site 3
- How to remove the front grille 3
- I english 2 3
- Indoor unit 3
- Installation tips 3
- Wireless remote controller 3
- How to attach the front grille 4
- How to attach the front panel 4
- How to remove the front panel 4
- How to set te different addresses 4
- I english 4
- Installation tips 4
- Pcb in the indoor unit 4
- Wireless remote controller 4
- Ftx25 35 ftk25 35 atx25 35 atk25 35 5
- Ftxs25 35 ftks25 35 atxs25 35 atks25 35 5
- I english 4 5
- Indoor unit installation drawings 5
- Install air puriying filter on air filter 5
- Adjusting the angle 6
- Iiii caution 6
- Intelligent eye sensor 6
- Boring a wall hole and installing wall embedded pipe 7
- I english 6 7
- Indoor unit installation 7
- Installing the mounting plate 7
- 2 left side left back or left bottom piping 8
- Caulk this hole with putty or caulking material bind with plastic tape 8
- Do not apply lubricating oil refrigerant machine oil when inserting application of causes deterioration and drain leakage of the plug 8
- Drain hose 8
- I english 8
- Indoor unit installation 8
- Insert a hexagon wrench 4 mm 8
- Installing indoor unit 8
- No gap 8
- Wrap insulating tape around the bent portion of refrigerant pipe overlap at least half the width of the tape with each turn interconnecting wires 8
- _en_2p098777 1 fm page 7 friday october 18 2002 1 26 pm 8
- 3 wall embedded piping 9
- I english 8 9
- Iiii warning 9
- Wiring 9
- _en_2p098777 1 fm page 8 friday october 18 2002 1 26 pm 9
- Drain piping 10
- I english 10
- Indoor unit installation 10
- When connecting to an ha system 10
- Align the centres of both flares and tighten the flare nuts 3 or 4 turns by hand then tighten them fully with the torque wrenches use torque wrenches when tightening the flare nuts to prevent damage to the flare nuts and escaping gas 11
- Cut the pipe end with a pipe cutter 2 remove burrs with the cut surface facing downward so that the chips do not enter the pipe 3 put the flare nut on the pipe 4 flare the pipe 5 check that the flaring is properly made 11
- Do not use mineral oil on flared part 2 prevent mineral oil from getting into the system as this would reduce the lifetime of the units 3 never use piping which has been used for previous installations only use parts which are delivered with the unit 4 do never install a drier to this r 410a unit in order to guarantee its lifetime 5 the drying material may dissolve and damage the system 6 incomplete flaring may cause refrigerant gas leakage 11
- Flaring the pipe end 11
- Iiii warning 11
- Protect the open end of the pipe against dust and moisture 2 all pipe bends should be as gentle as possible use a pipe bender for bending bending radius should be 30 to 40 mm or larger 11
- Refrigerant piping 11
- Refrigerant piping work 11
- To prevent gas leakage apply refrigeration machine oil on both inner and outer surfaces of the flare use refrigeration oil for r 410a 11
- 2 selection of copper and heat insulation materials 12
- I english 12
- Refrigerant piping work 12
- I english 12 13
- Test items 13
- Trial operation and testing 13
- Trial operation from remote controller 13
- P098777 1 m02b078 14
Похожие устройства
- Daikin ATKS35BVMB Сервис мануал
- Daikin ATX25BVMB Инструкция по монтажу
- Daikin ATX25BVMB Сервис мануал
- Daikin ATX35BVMB Инструкция по монтажу
- Daikin ATX35BVMB Сервис мануал
- Daikin ATK25BVMB Инструкция по монтажу
- Daikin ATK25BVMB Сервис мануал
- Daikin ATK35BVMB Инструкция по монтажу
- Daikin ATK35BVMB Сервис мануал
- Daikin FTS20BVMB Технические данные
- Daikin FTS20BVMB Инструкция по эксплуатации
- Daikin FTS20BVMB Сервис мануал
- Daikin FTS25BVMB Инструкция по эксплуатации
- Daikin FTS25BVMB Технические данные
- Daikin FTS25BVMB Сервис мануал
- Daikin FTS35BVMB Инструкция по эксплуатации
- Daikin FTS35BVMB Технические данные
- Daikin FTS35BVMB Сервис мануал
- Daikin FTYS20BVMB Инструкция по эксплуатации
- Daikin FTYS20BVMB Технические данные