Truvox SOLARIS Инструкция по эксплуатации онлайн [6/12] 602476
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Truvox SOLARIS Инструкция по эксплуатации онлайн [6/12] 602476

Truvox SOLARIS Инструкция по эксплуатации онлайн [6/12] 602476
6
5 Operation
5.1 Starting the machine
Fully unwind the supply cord and plug in to a
convenient socket outlet.
• With the solution tank filled and the handle set
at a comfortable height, the machine is ready
for use.
• Switch ON the brush motor, followed by the
vacuum motor.
• Release cleaning solution at regular intervals
by means of the handle triggers.
WARNING - Always ensure adequate
solution is on the floor, scrubbing without
solution could damage the floor surface
and/or the machine brush. Keep the machine
moving while the brush is rotating.
• IMPORTANT - Should the brush stop rotating
due to operation of the cut-out on the brush
motor, switch OFF the machine and allow to
cool for a few minutes. Press the cut-out reset
button on left hand side (Fig.5), and restart the
machine.
Fig 5
• WARNING - If foam or liquid is emitted, switch
off immediately and empty recovery tank.
Liquid emitted could be hazardous as a result
of its temperature, or chemical content.
• To STOP the machine, release solution feed
triggers, switch off brush motor then vacuum
motor.
• Normal movement of the machine is in a
forward and backward direction.
• Proceed to operate the machine in the normal
manner, releasing cleaning solution from time
to time as required.
• For heavy soilage, scrub floor with cleaning
solution but with vacuum motor OFF. Scrub
floor again picking up the solution.
• When scrubbing is complete, unplug the
machine from the power supply, empty the
solution tank and clean and dry the machine.
• IMPORTANT - Dispose of unused cleaning
solution in accordance with the manufacturer’s
directions.
5.2 Changing the brush
WARNING - This appliance has been
designed for use with the brushes
specified by the manufacturer. The
fitting of other brushes may affect its safety.
Always ensure machine is unplugged before
fitting or removing parts.
• To change the brush, first remove both
recovery tank and solution tank to reduce
weight and avoid spillage.
• Move handle to upright position, pull
backwards and downwards to rest on the floor
thereby raising the base.
• Push end of brush shaft with a finger and
withdraw shaft completely.
• Place new brush in position and insert shaft
through brush until it clicks into place.
• Return machine to the floor, replace tanks and
reconnect hoses etc.
5.3 Changing squeegee blades
The squeegee blades are self adjusting for wear,
however when wet pick-up becomes ineffective,
or blades are damaged they should be replaced
as follows.
• Raise machine base as for a brush change.
• Slide squeegee blades out sideways from the
holder.
• Slide new blades into place with the ribbed
side facing outwards.
• Return machine to the floor.
5.4 Fitting the side brush
Always ensure machine is unplugged before
fitting or removing parts.
• Remove recovery and solution tank, and raise
machine base as for a brush change.
• Remove shaft from brush and position the
magnetic brush guard on right hand side of
machine, locating the peg on the guard in the
hole in the side plate, and align the shaft hole.
• Insert side brush shaft through guard and push
right through main brush until it clicks into
place.
• Return machine to floor, replace tanks and
reconnect hoses.
5.5 When cleaning is finished
• When cleaning is finished, unplug the machine
from the power supply, and lift off and empty
the recovery and solution tanks over a suitable
sink or drain.
• Flush out the recovery tank with clean water.
• Replace tanks and wipe over the machine with
a damp cloth.
• Wipe squeegee blades clean.
• IMPORTANT - Dispose of unused cleaning
solution in accordance with the manufacturer’s
directions.
• Remove brush and wash in warm soapy water.

Содержание

Похожие устройства

Скачать