Daikin DEC101A51 [2/2] I rititititititriti

Содержание

• Di unit installation manual 1
• P14 5 7 1 1
• P14 5 711 1 1
• I rititititititriti 2
• P145712 1 2

Похожие устройства

• Daikin DEC102A51 Инструкция по монтажу
• Daikin FAA71BUV1B Инструкция по эксплуатации
• Daikin FAA71BUV1B Руководство по применению для установщика
• Daikin FAA100BUV1B Инструкция по эксплуатации
• Daikin FAA100BUV1B Руководство по применению для установщика
• Daikin FAQ71CVEB Инструкция по эксплуатации
• Daikin FAQ100CVEB Инструкция по эксплуатации
• Daikin FBQ20DAVMK Инструкция по эксплуатации
• Daikin FBQ20DAVMK Инструкция по монтажу
• Daikin FBQ24DAVMK Инструкция по эксплуатации
• Daikin FBQ24DAVMK Инструкция по монтажу
• Daikin FBQ36DAVMK Инструкция по эксплуатации
• Daikin FBQ36DAVMK Инструкция по монтажу
• Daikin FBQ45DAVMK Инструкция по эксплуатации
• Daikin FBQ45DAVMK Инструкция по монтажу
• Daikin FBQ48DAVMK Инструкция по эксплуатации
• Daikin FBQ48DAVMK Инструкция по монтажу
• Wolta ДПБ06-60-001 Инструкция по эксплуатации
• Wolta ДПБ06-60-001 Презентация
• Wolta ДПБ06-60-002 Инструкция по эксплуатации

is required before the power is turner T P1 Setting Facility equipment quantity change equipment Wiring Procedurel F1 F2 wiring between this equipment and centralized Power L Supply II I 2M 240V this equipment Address Nos 1 00 to 1 15 ate factory controlled before shipment shi p m en t Setting Method Control range D S1 centralized contre equipment Address range Connect the power supply and earth paragraph 8 numbers max her a product is discharged from the factory Set Address No low order with the centralized address setting switch RSI Referring to the table below set the address number low order Wiring with Facility Equipment CAUTioN The length of Abnormal input Closed Error is produced For changeover RSI Switch Setting Table No vo I tage contact I riTITITITITITriTI I Address No I 10 101 10 103 101 105 106 101 108 103 I ID I II I 12 I 13 I U 115 low order when a product is operating status input wiring error status npui IEC I 01 Ahl ExampIe Address No indicates the Address Nos 8 numbers max condition Number of centralized addresses used The number of centralized addresses used is determined by the top address set in this item iPower Supply Earth W i r iTg operation Exampe 1 specifications make correct connections terminal Connect the earth wiring to the Example 2 When the top addree Wiring s p e c i f i c a t i o n CAUTION This equipment can use the addresses between 1 00 and 4 15 It is impossible to use Address 5 00 and subsequent addresses and use any address Examplr scribed above Abnormal in the open condition before shi pnient and earth The relationship between each switch and abnormal input described below equipment Clamp Clamp equipment outdoor unit OFF factory preset before shipment is switched automatic reset before shi pment DS6 3 Setting OFF factory preset before shi pment I Wire connections and wire clamping should be as shown in the figure above Even when the facility equipment error is recovered no reset operation is performed if no operation input is turned OFF __ The error is displayed in case where an abnormal input was No error is displayed even when an abnormal input ii in case where the facility equipment is stopping malfunctioning may result Also in case where the wirings described above are routed in parallel be sure to connect the wirings at least 50 mm apart from the other 1P145712 1