Daikin ERRQ014AAY1 [44/459] Wiring diagram

Daikin ERRQ011AAY1 [44/459] Wiring diagram
Heating Daikin Altherma
41
Daikin Altherma High Temperature • Outdoor units • ERSQ-AAV1
6 Wiring diagram
6 - 1 Wiring diagram
3
6
2TW58746-2A
ERSQ-AV1
A1P Printed circuit board (Main)
A2P Printed circuit board (INV)
A3P Printed circuit board (Noise filter)
A4P Printed circuit board (C/H selector)
BS1BS5 Push button switch
(Mode, set, return, test, reset)
C1-C4 Capacitor
DS1 DIP switch
E1HC Crankcase heater
E7H Bottomplate heater
F1U, F4U Fuse(T 6.3A/250V)
F6U Fuse (T 5.0A/250V)
F7U, F8U Fuse(F 1,0A/250V)
FINTH Thermistor (Fin)
H1PH8P Light Emit. Diode (Serv. Monitor-Orange)
(H2P) Prepare, Test --------- Flickering
(H2P) Malfunction Detection -- Light up
HAP Light emitting diode
(A1P) (Service monitor green)
K1M Magnetic contactor (M1C)
K1R Magnetic relay (Y1S)
K2R Magnetic relay (Y2S)
K3R Magnetic relay (Y3S)
K4R Magnetic relay (E1HC)
K5R Magnetic relay
L1R Reactor
M1C Motor (Compressor)
M1F Motor (Fan) (upper)
M2F Motor (Fan) (lower)
PS Switching power supply
Q1DI Field earth leakage breaker (300mA)
R1 Resistor
R2 Resistor
R1T Thermistor (Air)
R2T Thermistor (Discharge)
R3T Thermistor (Suction 1)
R4T Thermistor (Heat exchanger)
R5T Thermistor (Suction2)
R6T Thermistor (Subcooling H.Ex)
R7T Thermistor(Liquid pipe1)
R8T Thermistor(Liquid pipe2)
S1NPH Pressure sensor(high)
S1NPL Pressure sensor(low)
S1PH Pressure switch (high)
V1R Power module
V2R, V3R Diode module
V1T IGBT
X1M Terminal strip(Power supply)
X2M Terminal strip(Control)
X1M Terminal strip(C/H selector)(A4P)
Y1E Electronic expansion valve (Main)
Y3E Electronic expansion valve (Subcool)
Y1S Solenoid valve (4 way valve)
Y3S Solenoid valve (hot gas)
Y4S Solenoid valve (U/L circuit)
Z1CZ8C Noise filter (ferrity core)
Z1FZ4F Noise filter
Notes
1 This wiring diagram only applies to the outdoor unit
2 L: Live N:Neutral g: Field wiring
3 D : Terminal strip F : Connector T : Connection R : Protective earth (screw)
: Connector p : Noiseless earth G : Terminal
4 Refer to the ’’wiring diagram sticker’’ (on back of front plate) on how to use BS1 - BS5 and DS1, DS2
switch-
5 Do not operate the unit by short-circuiting protection device S1PH
6 Colors BLU: blue, BRN: brown, GRN: green, RED: red, WHT:white, YLW: yellow, ORG: orange
7 Refer to the installation manual, for connection wiring to indoor-outdoor transmission F1 - F2.
8
Option
Only for *RRQ*or Option *KBPHTH16A
Position of
compressor
terminal
Wire entrance
Indoor BPH
Indoor F1, F2
(Note 4)
Outdoor
(Front)
Component location
101727_BW_EN_004_464_IC.pdf 45 9/06/2010 14:53:38

Содержание

Скачать