Mitsubishi Electric PKA-P3FAL2 [20/104] Installation de l appareil intérieur 3 het binnenapparaat installeren

Mitsubishi Electric PKA-P4FAL2 [20/104] Installation de l appareil intérieur 3 het binnenapparaat installeren
20
3
E
D
I
F
NL
SD
3. Installation de lappareil intérieur
3. Het binnenapparaat installeren
3. Installing the indoor unit
3. Anbringung der Innenanlage
3. Installazione della sezione interna
3. Installering av inomhusenheten
990 245
285
455
10×91=(910)
19
10184
280
60
30
3030
2980
900
91
90610
314280180240225
1818
A
B
C
G
I
H
F
E
D
1270
18 18 900 19
91
295 225 240 180 280 314
90750
60 280
80 29
3030
30
10184
13×91=(1183)
245
285
595
I
H
H
E
D
B
G
A
C
F
1 P2.5, P3
2 P4
(mm)
3.2. Installing the wall mounting fixture
1) Setting the wall mounting fixture and piping positions
s Using the wall mounting fixture, determine the units installation position
and the locations of the piping holes to be drilled.
Warning:
Before drilling a hole in the wall, you must consult the building contractor.
A Indoor unit centre line
B Left drain range
C Right drain range
D Hole for tapping screw
E Bolt hole
F Hole for tapping screw
G Contour of the unit
H Knockout hole for left rear piping
I Rear piping access hole (90-100 mm dia.)
3.2. Anbringung der Wandbefestigungen
1) Festlegung der Wandbefestigungen und Rohrleitungspositionen
s Mit den Wandbefestigungen die Einbauposition und die Position der zu
bohrenden Rohrleitungsöffnungen festlegen.
Warnung:
Bevor Sie ein Loch in die Wand bohren, müssen Sie den Bauherrn befragen.
A Mittellinie der Innenanlage
B Ablaßzone links
C Ablaßzone rechts
D Loch für Blechschraube
E Loch für Bolzen
F Loch für Blechschraube
G Umriß der Anlage
H Zum Ausbrechen vorgesehene Öffnungen für die Rohrleitung links hinten
I Zugangsöffnung für die hintere Rohrleitung (90-100 mm Durchmesser)
3.2. Installation de la structure de montage mural
1) Installation de la structure de montage mural et mise en place
des tuyaux
s A laide de la structure de montage mural, déterminer lemplacement dins-
tallation de lappareil et le lieu de forage des orifices pour les tuyaux.
Avertissement:
Avant de forer un trou dans le mur, veuillez demander lautorisation au res-
ponsable de l’édifice.
A Ligne centrale de lappareil intérieur
B Zone d’écoulement par la gauche
C Zone d’écoulement par la droite
D Orifice pour vis de fixation
E Orifice pour boulon
F Orifice pour vis de fixation
G Contour de lappareil
H Orifice à dégager pour le tuyau arrière gauche
I Orifice daccès du tuyau arrière (90-100 mm de diamètre)
3.2. De muurbevestigingsmal aanbrengen
1) De muurbevestigingsmal aanbrengen en de plaats van de pijpen
bepalen
s Bepaal met behulp van de muurbevestigingsmal de plaats waar het appa-
raat geïnstalleerd moet worden en waar de gaten voor de pijpen geboord
moeten worden.
Waarschuwing:
Neem contact op met de eigenaar van het gebouw voordat u gaten in de muur
gaat boren.
A Middellijn binnenapparaat
B Benodigde ruimte linkerafvoer
C Benodigde ruimte rechterafvoer
D Gat voor zelftappende schroef
E Gat voor bout
F Gat voor zelftappende schroef
G Omtrek van het apparaat
H Doordrukopening voor pijp linksachter
I Bevestigingsgat voor pijp achterkant (diam. 90-100 mm)
3.2. Installering av väggfästet
1) Montering av väggfästet och postionering av rör
s Använd väggfästet för att avgöra enhetens placering och placeringen av
hål för rörledningar som måste borras.
Varning:
Innan ett hål borras i väggen måste man rådgöra med byggnadsföretaget.
A Mittlinje, inomhusenhet
B Vänster dräneringsområde
C Höger dräneringsområde
D Hål för tappskruv
E Bulthål
F Hål för tappskruv
G Enhetens kontur
H Borttagbart hål för bakre vänster rörledningar
I Åtkomsthål för bakre rörledningar (90-100 mm dia.)
3.2. Installazione dellattrezzatura di montaggio a pa-
rete
1) Preparazione dellattrezzatura di montaggio e delle posizioni della
tubazione
s Utilizzando lattrezzatura di montaggio a parete, determinare la posizione
di installazione dellunità ed i punti in cui sarà necessario praticare i fori.
Avvertenza:
Prima di praticare un foro sulla parete, consultare il costruttore delledificio.
A Linea centrale della sezione interna
B Sezione di drenaggio sinistra
C Sezione di drenaggio destra
D Foro per vite di maschiatura
E Foro per bullone
F Foro per vite di maschiatura
G Profilo dellunità
H Foro di espulsione tubazione posteriore sinistra
I Foro di accesso alla tubazione posteriore (diam. 90-100 mm)

Содержание

Похожие устройства

Скачать