Haier HSU-12LEK13/R2(DB) [4/8] Use this switch in the test operation when the room
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Haier HSU-12LEK13/R2(DB) [4/8] Use this switch in the test operation when the room

Haier HSU-09LEK13/R2(DB) [4/8] Use this switch in the test operation when the room
Operation
Emergency Operation:
temperature is below 16
o
C, do not use it in the
Test operation:
Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds. After
you hear the "Pi" sound twice,
release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
Emergency operation and test operation
Use this operation only when the remote controller
is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once, which means
the start of this operation.
In this operation, the system automatically selects
the operation modes,cooling or fan or heat,according
to the room temperature.
It is not possible to operate in dry mode.
Room
temperature
Operation
mode
Designated
temperature
Timer
mode
Air flow
ABOVE 23
O
C
BELOW 23
O
C
COOLING
HEAT
23
O
C
26
O
C
NO
NO
AUTOMATIC
AUTOMATIC
Pi
(Cooling only uint）
Room temperature
Operation
mode
Designated
temperature
Timer
mode
Air flow
BELOW 23
O
C
FAN
26
O
C
NO
AUTOMATIC
Pi Pi
After 30 minutes, test operation ends automatically(Only for 22K,24K unit).
3
Note ：
During TURBO operation, in rapid COOL mode ,
the room
will show inhomogeneous temperature distribution.
Long period QUIET operation will cause effect of not too
cool or not too warm.
1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:
Remote controller:
Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). " "or " "will flash.
Timer On/Off On-Off Operation
BLANK
TIMER ON TIMER OFF TIMER ON-OFF
3.Press / button to set time.
It can be adjusted within 24 hours.
Hints:
After replacing batteries or a power failure happens, time
setting should be reset.
According to the Time setting sequence of TIMER ON or
TIMER OFF, either Start-Stop or Stop-Start can be achieved.
TIMER OFF-ON
0.5h
0.5h 0.5h
0.5h
Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.
Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.
After adjust the time,press button and confirm the
time ON or OFF button will not flash any more.
4.Confirm timer setting
5.Cancel timer setting
Press the timer button by times until the time display
eliminated.
TURBO/QUIET Operation
(This function is unavailable on some models.)
(1)
TURBO Operation
(2)
QUIET Operation
When you need rapid heating or cooling, you can use this function.
Press button to enter additional options, when cycle
display to , will flash，and then press ,enter to
quiet function. When cancel the function, please enter
additional options again and to cancel quiet function.
Press TURBO button, the remote controller will show ,
and then achieve to the turbo function. Press again this
TURBO button , the turbo function will be cancelled.
Press button to enter additional options, when cycle
display to , will flash，and then press ,enter to
health function. When cancel the function, please enter
additional options again and to cancel health function.
HEALTH Operation
(This function is unavailable on some models.)
a lot of anion effectively balance the quantity of position
up the dust sediment in the room and finally clean the
and anion in the air and also to kill bacteria and speed
air in the room.
The anion generator in the airconditioner can generate

Содержание

Похожие устройства

Скачать