Haier HSU-18HRA103/R2 [2/8] Be sure that the loading is in line with the load the battery then put on the cover again
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Haier HSU-18HRA103/R2 [2/8] Be sure that the loading is in line with the load the battery then put on the cover again

Haier HSU-18HRA103/R2 [2/8] Be sure that the loading is in line with the load the battery then put on the cover again
Outdoor Unit
Signal receiver hole
COOL display
HEAT display
TEMP display
HEALTH display
Dry display
4
2
3
1
6
7
5
4
Loading of the battery
1
2
3
4
1
2
3
Parts and Functions
Indoor Unit
4
2
3
1
6
7
5
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
(If the unit which you purchased
has healthy function,follow it.
TIMER OFF display
TIMER ON display
SLEEP display
Remote controller
If not,please ignore.)
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly.
After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the
button is kept pressed,time will
Display board
will increase
The following functions and related displays are not
26
25..
SWING button
9. ON/OFF button
10. TIMER ON display
11. FAN SPEED display
LOW HI
MED AUTO
12. LOCK display
13. SWING display
14. SLEEP display
15. HEALTH display
Operation mode
AUTO FANCOOL DRY
Remote controller
16. Operation mode display
18. POWER/SOFT display
19.
20.
TEMP display
21.
TIMER OFF display
22.
CLOCK display
23.
TEMP button
24.
FAN button
26.
5. SLEEP button
27.
SET button
28.
POWER/SOFT button
Used to select CODE A or B
will be displayed on
explanation.
1.CODE
3. TIMER button
4. CLOCK button
8. HEALTH button
6. MODE button
7. HOUR button
If pressed, the other buttons
be disa
bled
.Press it once
again,lock will be cancelled.
29.
LOCK
HEAT
17.Signal sending display
2.LIGHT button
Control the lightening and
the indoor
2
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
FRESH
button
30
HEALTH AIRFLOW button
which
extinguishing of
LED display board.
LCD.
special
Please select A without
will
When the remote controller
30.
RESET
button
button
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the
ver is apt to be disturbed in receiving
the signals,
so the distance to the indoor unit should be sho
rter.
type fluorescent lamp or
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up.
Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display
after taking-out, just need to press reset key.
Hint:
1
appears abnormal,use a
sharp pointed article to press
this button to reset the remote
controller normal.
avai
lable:
Actual indoor unit may vary from the one shown
in the manual, according to the product purchased.
2
Inlet grille
Air Purifying Filter
Outlet
Horizontal flap
Display board
(adjust up and down air flow
Don't adjust it manually)
(adjust left and
ow)
Vertical blade
Emergency
Switch
Anion generator
(inside)
right air fl
Inlet
(inside)
LIGHT button is not available for HSU-09HRA103/R2 and
HSU-12HRA103/R2.

Содержание

Похожие устройства

Скачать