Home
Главная
Festool
Электрические Пилы
LEX 2 150/7 691133
Инструкция по эксплуатации Страница: 14

Festool LEX 2 150/7 691133 Инструкция по эксплуатации онлайн [14/70] 7546

• Sawdust emission.

2.4 Noise and vibration information

Typical values established in compliance with EN

ISO 15 744/EN ISO 8662:

Sound pressure level 70 dB(A)

Measured acceleration

LEX 2 125/7, LEX 2 185/7 < 2,5 m/s²

LEX 2 125/3, LEX 2 150/3 = 3,0 m/s²

LEX 2 150/11 = 4,0 m/s²

LEX 2 150/7 = 4,5 m/s²

Uncertainty K = 1,5 m/s²

The noise level can exceed 85 dB(A) dur-

ing work.

Wear ear protectors!

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN ISO 15 744/EN ISO 8662

and are intended for machine comparisons. They

are also used for making preliminary estimates

regarding vibration and noise loads during opera-

tion. The emission values speciﬁ ed refer to the

main applications for which the air tool is used.

If the air tool is used for other applications, with

other tools or is not maintained sufﬁ ciently prior

to operation, however, the vibration and noise load

may be higher when the tool is used. Take into ac-

count any machine idling times and downtimes to

estimate these values more accurately for a speci-

ﬁ ed time period. This may signiﬁ cantly reduce the

load during the machine operating period.

3 Compressed-air supply and commis-

sioning

Make sure that the pneumatic tool is

switched off when you connect the com-

pressed-air supply.

3.1 Compressed-air processing

The Festool service unit VE should always be used

to ensure that Festool pneumatic tools function

correctly.

Consisting of a ﬁ lter, control unit, condensation

drain and lubricator, the service unit cleans and

lubricates the compressed air and keeps it free

of condensation.

Here, the lubricator should be set so that a drop

is applied to the compressed air approx. every

7-10 minutes.

Damage that occurs as a result of incorrect

compressed-air processing is excluded from

warranty claims.

We recommend a service unit with a 3/8“ con-

nector, when up to two Festool pneumatic tools

are used.

A compressor that supplies at 500 l/min and at

an operating pressure of 6 bar should be used to

supply compressed-air.

The diameter of the piping system must be suf-

ﬁ ciently large (at least 9 mm).

3.2 IAS 2 hose connector

The eccentric sander is a pneumatic tool for con-

nection to the Festool IAS 2 system.

This hose system combines three functions in

one hose:

- Compressed air supply (1.1)

- Exhaust air extraction (1.2)

- Dust extraction (1.3)

Connection and disconnection – see Fig. 3.

3.3 Commissioning

Pressing the lever (2.1) switches on the pneumatic

tool.

Releasing the lever switches the machine off

again.

4 Machine settings

The machine should always be discon-

nected from the compressed air supply

before any work is carried out on the ma-

chine.

4.1 Speed adjustment

You can regulate the rotational speed steplessly

between 6500 and 8000 rpm or 6000 and 7000 rpm

(LEX 2 150/11) using the adjusting wheel (2.2).

This enables you to optimise the cutting speed to

suit the material.

4.2 Suction unit

Sanding dust is extracted through the

extraction channels in the sanding pad

directly to the material removal point. To

guarantee optimized dust extraction, we

recommend using Festool extractors with

automatic switch-on/switch-off device for

compressed-air machines.

In order to prevent damage to the pneu-

matic motor, dust extraction must not be

carried out on the pneumatic tool when

it is at standstill.

4.3 Sanding pads

The sanding pads are different in weight,

depending on their diameter. Fitting sand-

ing pads of incorrect size causes excessive

vibration of the machine.

Only use sanding pads with an undamaged burr

layer.

The sanding pads are available in three degrees

of hardness to suit the type of application:

- Hard: high edge strength, for removing coarse

Содержание

Похожие устройства

Sawdust emission A compressor that supplies at 500 l min and at an operating pressure of 6 bar should be used to supply compressed air The diameter of the piping system must be suf ficiently large at least 9 mm 2 4 Noise and vibration information Typical values established in compliance with EN ISO 15 744 EN ISO 8662 Sound pressure level 70 dB A Measured acceleration LEX 2 125 7 LEX 2 185 7 2 5 m s2 LEX 2 125 3 LEX 2 150 3 3 0 m s2 LEX 2 150 11 4 0 m s2 LEX 2 150 7 4 5m s2 Uncertainty K 1 5 m s2 3 2 IAS 2 hose connector The eccentric sander is a pneumatic tool for con nection to the Festool IAS 2 system This hose system combines three functions in one hose Compressed air supply 1 1 Exhaust air extraction 1 2 Dust extraction 1 3 Connection and disconnection see Fig 3 OThe noise level can exceed 85 dB A dur ing work Wear ear protectors The emission values specified vibration noise were measured in accordance with the test con ditions stipulated in EN ISO 15 744 EN ISO 8662 and are intended for machine comparisons They are also used for making preliminary estimates regarding vibration and noise loads during opera tion The emission values specified refer to the main applications for which the air tool is used If the air tool is used for other applications with other tools or is not maintained sufficiently prior to operation however the vibration and noise load may be higher when the tool is used Take into ac count any machine idling times and downtimes to estimate these values more accurately for a speci fied time period This may significantly reduce the load during the machine operating period 3 3 3 Commissioning Pressing the lever 2 1 switches on the pneumatic tool Releasing the lever switches the machine off again Machine settings The machine should always be discon nected from the compressed air supply before any work is carried out on the ma chine 4 1 Speed adjustment You can regulate the rotational speed steplessly between 6500 and 8000 rpm or 6000 and 7000 rpm LEX 2 150 11 using the adjusting wheel 2 2 This enables you to optimise the cutting speed to suit the material Compressed air supply and commis sioning Make sure that the pneumatic tool is switched off when you connect the com pressed air supply 4 2 Suction unit Sanding dust is extracted through the extraction channels in the sanding pad directly to the material removal point To guarantee optimized dust extraction we recommend using Festool extractors with automatic switch on switch off device for compressed air machines In order to prevent damage to the pneu matic motor dust extraction must not be carried out on the pneumatic tool when it is at standstill 3 1 Compressed air processing The Festool service unit VE should always be used to ensure that Festool pneumatic tools function correctly Consisting of a filter control unit condensation drain and lubricator the service unit cleans and lubricates the compressed air and keeps it free of condensation Here the lubricator should be set so that a drop is applied to the compressed air approx every 7 10 minutes Damage that occurs as a result of incorrect compressed air processing is excluded from warranty claims We recommend a service unit with a 3 8 con nector when up to two Festool pneumatic tools are used 4 3 Sanding pads The sanding pads are different in weight depending on their diameter Fitting sand ing pads of incorrect size causes excessive vibration of the machine Only use sanding pads with an undamaged burr layer The sanding pads are available in three degrees of hardness to suit the type of application Hard high edge strength for removing coarse 14

Скачать