![Haier AE212FCAKA [17/37] Operating instructions](/img/pdf.png)
Haier AE212FCAKA [17/37] Operating instructions
![Haier AE142FCAKA [17/37] Operating instructions](/views2/1821687/page17/bg11.png)
Operating Instructions
16
SWING
SET
LOCK
RESET
HEALTH
FAN
MODE SLEEP
CLOCK
TIMER
ON
OFF
*
MODE
FAN
HEALTH
TEMP
CLOCK SET
TIMER SLEEP
RESET
FILTER RESET
ON/OFF
AM
SET
OFF
1.How to use the health function (only for units
with this function)
After set the right function mode, press health button,
remote controller or wire controller displays ì î,
oxygen pump or negative ion generator starts up to apply
oxygen or negative ion to indoor unit. Press the button
again,the sign ì î disappeared and negative ion generator
stops working. After all health function of the indoor unit
being fully canceled, oxygen pump stopped.
CAUTION:
When the temperature of the outdoor unit is lower than 4 ,
oxygen pump is automatically stopped, if press health button
just then, oxygen pump could not start up. But if the air
conditioner has the negative ion function simultaneous,
when press the health button, negative ion function could
still be operated. When the temperature of the outdoor unit
is higher than 6 , oxygen pump could automatically resume
to oxygen-make function.
AM
Power Failure Compensation (to be applied for a necessary situation)
:
Setting Method: When the remote controller is on (excluding timer mode and fan mode),
press the "Sleeping" button on the remote controller 10 times within 5 seconds, and after the buzzer rings 4 times,
the air conditioner will enter the state of power failure compensation.
Cancel Method: Press the "Sleeping" button on the remote controller 10 times within 5
seconds, and after the buzzer rings 2 timer, the power failure compensation mode will be cancelled.
Notes: When a power failure suddenly occurs during the air conditioner is working after the power failure
compensation is set, if the air conditioner will not be used for a long time, please cut off the power supply to prevent
its operation from being resumed after the power is supplied again, or press the "Switch On/Off" button after the
power comes again.If the controller no sleep key ,use the "swing" key instead the "sleeping" on setting the auto
restart function.
After the power failure compensation is set, if power failure suddenly occurs while the air conditioner is working, it
will resume the previous working state when the power is supplied again.
On the "Health" mode, if you want to setting
timing open mode, should close the health
first: On the timing open mode, please don't
use health function.
About the remote cnotrol operation, above only take wired remote controller and remote controller (1) as a
example about the remote controller (2) and remote receiver use method, it is the same remote controller (1) ,
please use refer to above method.
No sleep function when use remote (2) and remote receiver.
SWING
Health Function
C
C
User Caution
Concerning MRV Auto Restart function for H-MRV models
Haier Auto Restart function when the unit power drops down suddenly, the unit microprocessor will store the previous
working condition and when the power is on again, the unit will run as this memory.
Auto Restart function is designed basically on the MRV whole system, but it is suitable for each indoor unit individually.
If some of indoor units power cut down, but the outdoor unit and the other indoor units still work, maybe problems
will happen such as freezing at cooling mode and overload protection at heating mode on those indoor units without power.
Reason
When one or some indoor units power drops down and the other indoor units are still work, the indoor units without
the power, will keep the previous working condition before the power is off. And expansion valve keeps open at a kind of
opening rate condition as the previous requirement, so there is refrigerant flowing in the exchanger, but the indoor fan stops
working. If the units work at cooling mode, the indoor units without the power will maybe make freezing. If the unit works
at heating mode, maybe the outdoor unit compressor will stop because of the pressure or temperature protection. This is
our design basically on Auto Restart function currently.
Haier, Herewith, solemnly informs our customers, installers, distributors, etc. when making installation, please make sure
when the power is shut down whether artificially or accidentally, the whole system including outdoor unit and all the
indoor units must be off. If you do not make the installation as our indication, Haier will not be responsible for any problem
resulting from this.
TEMP
FRESH
LIGHT
Содержание
- Ceiling concealed type air conditioner indoor unit 1
- Contents 1
- Instruction manual 1
- Cautions 2
- Cautions 3
- Ae072fcaka 4
- Ae09 212fcaka 4
- Ae242fcaka 4
- Remote controller operation of remote controller 7
- Remote lcd display contents and key name and each key function introduction 7
- Make sure that the remote controller is used within 7 meters from receiver window of the wire controller and there are no obstructions in between the remote controller or wire controller should be handled with care 8
- Remote lcd display contents and key name and each key function introduction 8
- When operating the remote controller in an area where electronically controlled lights are installed or wireless handsets are used move closer to the indoor unit as the function of the remote controller might be affected by signals from this equipment 8
- Battery loading batteries are fitted as follows 9
- Clock set 9
- When unit is started for the first time clock should be adjusted as follows press clock button am or pm flashes press or to set correct time each press will increase or decrease 1min if the button is kept depressed time will change quickly after time setting is confirmed press set am and pm stop flashing while clock starts working 9
- Important points of safety 10
- Warning 10
- Important points of safety 11
- Important points of safety 12
- 1 unit start 13
- 2 select operation mode 13
- 3 select temp setting 13
- 4 fan speed selection 13
- 5 unit stop 13
- Auto run cool heat and dry operation 13
- Operating instructions 13
- Recommendations 13
- Operating instructions 14
- Timer on off 14
- Timer operation 14
- To cancel timer mode 14
- Operating instructions 15
- Timer on off 15
- Timer operation 15
- To cancel timer mode 15
- Comfortable sleep 16
- In cooling dehumidifying mode 16
- In heating mode 16
- Operating instructions 16
- Sleep function 16
- Health function 17
- Operating instructions 17
- User caution 17
- Trouble shooting 18
- Trouble shooting 19
- Poor cooling 20
- Poor cooling or heating 20
- When fault occurs 20
- Information about application 21
- Notice to users 21
- Installation precautions 22
- Warning 22
- Attention 23
- Electrical requirements 23
- Installation precautions 23
- Installing tools 23
- Warning 23
- After selecting the unit installation location proceed the following steps 1 drill a hole in the wall and insert the connecting pipe and wire through a pvc wall through tube purchased locally the wall hole shall be with a outward down slope of at least 1 100 see figure 2 2 before drilling check that there is no pipe or reinforcing bar just behind the drilling position drilling shall avoid at positions with electric wire or pipe 3 mount the unit on a strong and horizontal building roof if the base is not firm it will cause noise vibration or leakage see figure 6 4 support the unit firmly 5 change the form of the connection pipe connection wire and drain pipe so that they can go through the wall hole easily 24
- Figure showing installation dimensions unit mm 24
- For electrical heating unit the air outlet not allowed directly connecting with canvas etc easy catching fire goods 2 this series indoor unit are all middle static pressure 30 pa external static pressure 3 an access port must be provided during installation of indoor unit for maintenance 24
- Installation procedure 24
- Installation of indoor unit 25
- Installation procedure 25
- When installing the ceiling concealed type indoor unit a specially designed return air bellows shall be installed as shown in figure 3 figure 4 25
- Air duct insulation insulation layer is needed for air supply and return duct first paste a glue nail to the air duct and then attach the insulation cotton that has a tinfoil layer and use the glue nail cover to fix finally seal the air duct interface with tinfoil adhesive tape closely as shown in fig3 26
- Installation for air duct of indoor unit 1 installation for air supply duct this type of unit uses circular air duct with its caliber of 180mm an additional transitive air duct is necessary for the circular air duct to connect to the air supply inlet it should be also connected to its respective air diffuser separately see fig adjust the wind speed of each air diffuser outlet to keep in line on the whole so as to meet a demand of the air conditioner in the room 26
- Installation for air return duct use rivets to connect the air return duct to the air return inlet of the indoor unit the other end connects to the air return shutter as shown in fig 26
- Installation of indoor unit 26
- Installation procedure 26
- Installation of indoor unit 27
- Installation procedure 27
- Installation of remote controller 28
- Installation procedure 28
- Connecting wiring method of receiver 29
- Installation procedure 29
- Refer the indoor unit wiring diagram safety cautions see the electrical wiring part 29
- Caution 30
- Drain pipe 30
- Installation procedure 30
- Efrigerant piping 31
- Installation procedure 31
- Pipe cutting and expanding 31
- Pipe expansion dimensions as follows 31
- Efrigerant piping 32
- Installation procedure 32
- Caution 33
- Electric wiring 33
- Installation procedure 33
- Warning 33
- Wiring connection method the wiring diagram is attached inside the machine 33
- Field setting 34
- Installation procedure 34
- Indoor unit malfunction display code 35
- Malfunction 35
- Outdoor unit malfunction display code when the wire remote controller display e1 can check the indoor unit control board led1 or the outdoor unit control board led1 outdoor unit control board led alarma or alarmb 35
- Indoor unit malfunction 36
- Malfunction 36
- Outdoor unit malfunction 36
- Remote controller timer and operation indicator malfunction code when the unit running timer indicator flash stand for indoor unit malfunction operation indicator flashing stand for outdoor unit malfunction 36
Похожие устройства
- Haier AE212FCAKA Сервис мануал
- Haier AE242FCAKA Инструкция по эксплуатации
- Haier AE242FCAKA Сервис мануал
- Haier AE092FCAHA Инструкция по эксплуатации
- Haier AE092FCAHA Сервис мануал
- Haier AE182FCAHA Инструкция по эксплуатации
- Haier AE182FCAHA Сервис мануал
- Haier AE092FCBHA Сервис мануал
- Haier AE182FCBHA Сервис мануал
- Haier AE112FCBIA Сервис мануал
- Haier AE182FCBIA Сервис мануал
- Haier AP182FAAHA Сервис мануал
- Haier AP182FABHA Сервис мануал
- Haier AF122FCBHA Сервис мануал
- Haier AF092FCBHA Сервис мануал
- Haier AS062FMAHA Сервис мануал
- Haier AS072FMAHA Сервис мануал
- Haier AS092FMAHA Сервис мануал
- Haier AS092FMBHA Сервис мануал
- Haier AS122FMAHA Сервис мануал