Haier HW-09CD03 [22/22] Installation process

Содержание

• Manual 1
• Operation 1
• Remote controlled window type 1
• Room air conditioner 1
• Cooling 2
• Hcatin 2
• The machine is adaptable in following situation 2
• Description of the parts 3
• Display panel time indicator 3
• Emergency switch 3
• Machine body 3
• Operation mode indicator 3
• Power indicator j 3
• Wireless remote control 3
• Description of the parts 4
• Cz mode 5
• Display 5
• Fan speed indicator j 5
• For cooling only type 5
• I operation j 5
• Operation mode indicator j 5
• Remote controller 5
• Signal indicator 5
• Temp indicator 5
• Time display 5
• Timer indicator 5
• Attach the lid 6
• Handing the wireless remote controller 6
• Insert the dry batteries 6
• Inserting dry batteries 6
• Jk the appearance is different by models 6
• Parts and functions 6
• Remove the lid 6
• Verify by the indicators 6
• Auto mode 7
• Cooling operation 8
• Dry mode 9
• Fan operation 10
• Aumn ike fmrrm inn 11
• Heat operation 11
• O o o o 11
• Xthis function is only for heat pump the other functions arc the same 11
• R hint 12
• Sleep mode setting 12
• Timer operation 13
• Operation 14
• Close vent open 15
• Function introduction 15
• ______________ œzd 15
• Do remember the following 16
• Usage musts 16
• Cleaning of the air filter 17
• Disposal of the condensed water 17
• Maintenance 17
• Cleaning of the shell and remote controller 18
• Maintenance 18
• Trouble shooting 19
• Be sure to use specific power circuit 20
• I select position where the structure is firm 20
• Installation diagram 20
• Installation instruction 20
• Is required 20
• It should be installed like this the back side outdoor side is lower so that the drained 20
• Requirements on electricity 20
• Select position where the cooled air can be blown to every comer 20
• Select position where the drainage is smooth 20
• Select position where the outdoor airflow will not influence the neighbors 20
• Select position where there s no dangerous gas or oil smoke nearby 20
• Select position where there s no direct sunlight if the sunlight is inevitable sunshading device 20
• Select position where ventilation inside and outside can be assured 20
• Selection of die installation position 20
• The enclosed accessories of the conditioner are 20
• Water can flow out smoothly 20
• Width of the wall should be less than 295mm 20
• Installation process 21
• Installation process 22

Похожие устройства

• Haier HW-09CA12 Инструкция по эксплуатации
• Haier HW-12CA03 Инструкция по эксплуатации
• Haier HW-12HA03 Инструкция по эксплуатации
• Haier HW-12HA04 Инструкция по эксплуатации
• Haier HW-12eA03 Инструкция по эксплуатации
• Haier HW-12eA04 Инструкция по эксплуатации
• Haier HW-18HB03 Инструкция по эксплуатации
• Haier AW094AAMBA Инструкция по эксплуатации
• Haier AW122AAACA Инструкция по эксплуатации
• Haier AW124AAMBA Инструкция по эксплуатации
• Haier HW-12CA13 Инструкция по эксплуатации
• Haier HW-07CA03 Инструкция по эксплуатации
• Haier HW-07HA03 Инструкция по эксплуатации
• Haier HW-09C03 Инструкция по эксплуатации
• Haier HW-09CE03 Инструкция по эксплуатации
• Haier HW-09HA03 Инструкция по эксплуатации
• Haier HW-12C03 Инструкция по эксплуатации
• Haier HW-12H03 Инструкция по эксплуатации
• Haier HW-18C03(T3) Инструкция по эксплуатации
• Vodotok НСБ-130 ЭКО Инструкция по эксплуатации

Installation process 9 After installation of all the accessories put the whole machine on the iron frame If there s water outlet flexible pipe lead the pipe to needed position see Fig 4 10 Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and the leaking of the coolness 11 After installation of the conditioner insert the power plug into the outlet and perform test run Fig 4