![Lamborghini FL D H F24 [4/32] Fl d hf](/img/pdf.png)
Lamborghini FL D H F24 [4/32] Fl d hf
![Lamborghini FL D H F32 [4/32] Fl d hf](/views2/1824207/page4/bg4.png)
FL D HF
4
EN
cod. 3541P701 - Rev. 00 - 10/2018
System draining
The drain faucet ring nut is located under the safety valve inside the boiler.
To drain the system, turn the ring (ref. 1 - fig. 9) counter-clockwise to open the faucet. Do
not use any tools; use hands only.
To drain only the water in the boiler, first close the shut-off valves between the system
and boiler before turning the ring.
fig. 9- Safety valve with drain faucet
3. INSTALLATION
3.1 General Instructions
BOILER INSTALLATION MUST ONLY BE PERFORMED BY QUALIFIED PERSON-
NEL, IN ACCORDANCE WITH ALL THE INSTRUCTIONS GIVEN IN THIS TECHNICAL
MANUAL, THE PROVISIONS OF CURRENT LAW, THE PRESCRIPTIONS OF NA-
TIONAL AND LOCAL STANDARDS AND THE RULES OF PROPER WORKMANSHIP.
3.2 Place of installation
B
The combustion circuit is sealed with respect to the place of installation
and therefore the unit can be installed in any room except in a garage. The
place of installation must be sufficiently ventilated to prevent the creation
of dangerous conditions in case of even small gas leaks. Otherwise there
may be a risk of suffocation and intoxication or explosion and fire. This
safety precaution is required by EEC Directive No. 2009/142 for all gas
units, including so-called sealed chamber units.
The unit is designed to operate in a partially protected place, with a minimum tempera-
ture of -5°C. If provided with the special antifreeze kit, it can be used with a minimum tem-
perature down to -15°C. The boiler must be installed in a sheltered place, for instance
under the slope of a roof, inside a balcony or in a protected recess.
The place of installation must be free of flammable materials, objects and dusts or cor-
rosive gases.
The boiler is arranged for wall mounting and comes as standard with a hooking bracket.
Wall fixing must ensure stable and effective support for the generator.
A
If the unit is enclosed in a cabinet or mounted alongside, there must be suffi-
cient space for removing the casing and for normal maintenance activities
3.3 Plumbing connections
Important
B
The safety valve outlet must be connected to a funnel or collection pipe to pre-
vent water spurting onto the floor in case of overpressure in the heating circuit.
Otherwise, if the discharge valve cuts in and floods the room, the boiler manu-
facturer cannot be held liable.
B
Before making the connection, check that the unit is arranged for operation with
the type of fuel available and carefully clean all the system pipes.
Carry out the relevant connections according to the diagram in fig. 25 and the symbols
on the unit.
Note: The unit is equipped with an internal bypass in the heating circuit.
Water system characteristics
In the presence of water harder than 25° Fr (1°F = 10ppm CaCO
3
), use suitably treated
water in order to avoid possible scaling in the boiler.
Antifreeze system, antifreeze fluids, additives and inhibitors
When necessary, antifreeze fluids, additives and inhibitors can be used only if the man-
ufacturer of such fluids or additives guarantees that they are suitable and do not cause
damage to the exchanger or other components and/or materials of the boiler and system.
Do not use generic antifreeze fluids, additives or inhibitors that are not specific for use in
heating systems and compatible with the materials of the boiler and system.
Connection to a storage tank for domestic hot water
The unit's electronic card is arranged for managing an external storage tank for domestic
hot water production. Carry out the plumbing connections according to the diagram of
fig. 10. Carry out the electrical connections as shown on the wiring diagram in fig. 30. It
is necessary to use the kit code 1KWMA11W. At the next lighting, the boiler control sys-
tem detects the hot water tank probe and automatically configures the DHW function, ac-
tivating the display and relevant controls.
fig. 10- Diagram of connection to an external hot water tank
8 Domestic hot water outlet
9 Cold water inlet
10 System delivery - Ø 3/4”
11 System return - Ø 3/4”
95 Diverter valve
209 Hot water tank delivery - Ø 3/4”
210 Hot water tank return - Ø 3/4”
3.4 Gas connection
The gas must be connected to the relevant connection (see fig. 25) in conformity with the
current standards, using a rigid metal pipe or a continuous surface flexible s/steel tube
and installing a gas cock between the system and boiler. Make sure all the gas connec-
tions are tight.
3.5 Electrical connections
IMPORTANT
B
BEFORE CARRYING OUT ANY OPERATION THAT REQUIRES REMOVING
THE CASING, DISCONNECT THE BOILER FROM THE ELECTRIC MAINS
WITH THE MAIN SWITCH.
NEVER TOUCH THE ELECTRICAL COMPONENTS OR CONTACTS WITH
THE MAIN SWITCH TURNED ON! DANGER OF ELECTRIC SHOCK WITH
RISK OF INJURY OR DEATH!
B
The unit must be connected to an efficient grounding system in accordance with
applicable safety regulations. Have the efficiency and suitability of the ground-
ing system checked by professionally qualified personnel; the Manufacturer de-
clines any liability for damage caused by failure to earth the system.
The boiler is prewired and provided with a three-pole cable, without a plug, for
connection to the electric line. The connections to the grid must be made with
a permanent connection and equipped with a bipolar switch whose contacts
have a minimum opening of at least 3 mm, interposing fuses of max. 3A be-
tween the boiler and the line. Make sure to respect the polarities (LINE: brown
wire / NEUTRAL: blue wire / GROUND: yellow-green wire) in the connections
to the electric line.
B
The unit's supply cable MUST NOT BE REPLACED BY THE USER. If the ca-
ble gets damaged, turn the unit off and have the cable replaced only by
professionally qualified personnel. In case of replacement, only use cable
“HAR H05 VV-F” 3x0.75 mm2 with max. external diameter of 8 mm.
Room thermostat (optional)
B
IMPORTANT: THE ROOM THERMOSTAT MUST HAVE VOLTAGE-FREE
CONTACTS. CONNECTING 230 V TO THE ROOM THERMOSTAT TERMI-
NALS WILL PERMANENTLY DAMAGE THE ELECTRONIC BOARD.
When connecting time controls or a timer, do not take the power supply for
these devices from their breaking contacts Their power supply must be by
means of direct connection from the mains or with batteries, depending on the
kind of device.
1
8
9
0
1
2
3
4
10
11
14
56
36
32
74
95
241
114
209
210
278
27
Содержание
- Instructions for use installation and maintenance 1
- Fl d hf 2
- Fl d hf 3
- Fl d hf 4
- Fl d hf 5
- Fl d hf 6
- Fl d hf 7
- Cod 3541p701 rev 00 10 2018 8
- Configuration menu 8
- Fl d hf 8
- Heating power adjustment 8
- If the test mode is activated and enough hot water is drawn to activate the dhw mode the boiler remains in test mode but the 3 way valve goes to dhw 8
- Parameters indicated by the letter p are available which are also modifiable from remote timer control 8
- Parameters with more than one description vary their function and or range in rela tion to the setting of the parameter given in brackets 2 parameters with more than one description are reset to the default value if the pa rameter given in brackets is modified 8
- Press the heating buttons to scroll the list of parameters in increasing or decreasing or der press the dhw buttons to view or modify the value of a parameter the change will be automatically saved 8
- Service menu 8
- The card service menu is accessed by pressing the reset button for 20 seconds 4 sub menus are available press the heating buttons to select in increasing or decreasing or der ts in hi or re ts means transparent parameters menu in means information menu hi means history menu after selecting the submenu press the re set button again to access it re means history menu reset see description 8
- The configuration menu is accessed by pressing the dhw buttons together for 10 sec onds 12 parameters indicated by the letter b and not modifiable from remote timer control are available 8
- The test mode is automatically deactivated in any case after 15 minutes or on stopping of hot water drawing if enough hot water has been drawn to activate the dhw mode 8
- To adjust the heating power switch the boiler to test mode see sec 4 press the heating buttons detail 3 fig 1 to increase or decrease the power min 00 max 100 press the reset button within 5 seconds and the max power will remain that just set exit test mode see sec 4 8
- To deactivate the test mode press the heating buttons details 3 and 4 fig 1 together for 5 seconds 8
- To exit the configuration menu press the dhw buttons together for 10 seconds or exiting occurs automatically after 2 minutes 8
- Ts transparent parameters menu 8
- Fl d hf 9
- Cod 3541p701 rev 00 10 2018 10
- Diagnostics 10
- Fl d hf 10
- List of faults 10
- Other faults cause temporary shutdowns marked with the letter f which are automat ically reset as soon as the value returns within the boiler s normal working range 10
- Table 8 10
- Table 9 legend fig 27 fig 28 and fig 29 10
- Technical data and characteristics 10
- The boiler has an advanced self diagnosis system in case of a boiler fault the display will flash together with the fault symbol detail 11 fig 1 indicating the fault code 10
- There are faults that cause permanent shutdowns marked with the letter a to restore operation press the reset button detail 6 fig 1 for 1 second or reset on the op tional remote timer control if installed at this point the display will show d4 for about 30 seconds or d5 for about 5 minutes which indicates the waiting time after which the boiler will resume normal operation if the boiler fails to restart it is necessary to eliminate the fault 10
- Troubleshooting 10
- Fl d hf 11
- Fl d hf 12
- Fl d hf 13
- Fl d hf 14
- Fl d hf 15
- Fl d hf 16
- Fl d hf 17
- Fl d hf 18
- Fl d hf 19
- Fl d hf 20
- En 1856 1 21
- Fl d hf 21
- Fl d hf24 fl d hf32 21
- Fl d hf 22
- Cod 3541p701 rev 00 10 2018 23
- Fl d hf 23
- Fl d hf 24
- 9 27 28 29 25
- A 6 1 1 d4 30 d5 5 25
- Cod 3541p701 rev 00 10 2018 25
- Fl d hf 25
- Fl d hf 26
- Fl d hf 27
- Fl d hf 28
- Fl d hf 29
- Fl d hf 30
Похожие устройства
- Lamborghini FL D H F24 Каталог запчастей
- Lamborghini FL D H F24 Каталог
- Lamborghini FL D H F32 Инструкция по эксплуатации
- Lamborghini FL D H F32 Каталог запчастей
- Lamborghini FL D H F32 Каталог
- Haier HW-18CB03 Инструкция по эксплуатации
- Haier HW-09C04 Инструкция по эксплуатации
- Haier HW-09HA04 Инструкция по эксплуатации
- Haier HW-12C04 Инструкция по эксплуатации
- Haier HW-07CA12 Инструкция по эксплуатации
- Haier HW-08C12 Инструкция по эксплуатации
- Haier HW-09C12 Инструкция по эксплуатации
- Haier HW-10C12 Инструкция по эксплуатации
- Haier HW-12C12 Инструкция по эксплуатации
- Haier HW-08C13 Инструкция по эксплуатации
- Haier HW-12C13 Инструкция по эксплуатации
- Haier HW-18C13(T3) Инструкция по эксплуатации
- Haier HW-18CA13 Инструкция по эксплуатации
- Haier AW094AAMAA Инструкция по эксплуатации
- Haier AW098AAAAA Инструкция по эксплуатации