![Yaesu FT-1907 [29/88] Ctcss dcs epcs](/img/pdf.png)
Yaesu FT-1907 [29/88] Ctcss dcs epcs
![Yaesu FT-1907 [29/88] Ctcss dcs epcs](/views2/1824638/page29/bg1d.png)
25FT-1907R OPERATING MANUAL
TONE SEARCH SCANNING
In operating situations where you don’t know the CTCSS tone or DCS code being used by
another station or stations, you can command the radio to listen to the incoming signal and
scan in search of the tone being used. Two things must be remembered in this regard:
You must be sure that your repeater uses the same tone type (CTCSS vs. DCS).
Some repeaters do not pass the CTCSS tone or DCS code; you may have to listen to the
station(s) transmitting on the repeater uplink (input) frequency in order to allow Tone
Search Scanning to work.
To scan for the tone in use:
1. Set the radio up for either CTCSS or DCS Decoder operation (see the previous discus-
sion). In the case of CTCSS, “TSQ” will appear on the display; in the case of DCS,
“DCS” will appear on the display.
2. Press the Microphone’s
[
P3
]
key momentarily to start scan-
ning for the incoming CTCSS or DCS tone/code.
3. When the radio detects the correct tone or code, it will halt
on that tone/code, and audio will be allowed to pass.
4. Press the Microphone’s
[
P3
]
key momentarily to lock in that tone/code and exit to
normal operation.
If the Tone Scan feature does not detect a tone or code, it will continue to scan
indefinitely. When this happens, it may be that the other station is not sending any
tone. You can press the Microphone’s
[
P3
]
key to halt the scan at any time.
You may listen to the (muted) signals from the other stations during Tone Scanning when
Set Mode Item “54 TS MUT” is set to “OFF.” See page 80 for details. You can also change
the Tone Search scanning speed, using Set Mode Item “55 TS SPD.” See page 80 for
details.
Tone Scanning works either in the VFO or Memory mode.
CTCSS/DCS/EPCS OPERATION
Содержание
- Fm transceiver 1
- Ft 1907r 1
- Peratin 1
- Contents 2
- Eferenc 3
- Ft 1907r 3
- Eferenc 4
- Ft 1907r 4
- Verview 4
- Ft 1907r 5
- Ntroduction 5
- Ft 1907r 6
- General 6
- Pecifications 6
- Receiver 6
- Transmitter 6
- Ccessorie 7
- Ft 1907r 7
- Ptions 7
- Ft 1907r 8
- Nstallation 8
- Ft 1907r 9
- Nstallation 9
- Ft 1907r 10
- Nstallation 10
- Ft 1907r 11
- Nstallation 11
- Ft 1907r 12
- Mobile power connections 12
- Mobile speakers 12
- Nstallation 12
- Ac power supplies 13
- Ft 1907r 13
- Nstallation 13
- Ontrol 14
- Witches 14
- D mr mw key 15
- Dial knob 15
- Display 15
- Ft 1907r 15
- Low a n key 15
- Ontrol 15
- Rev dw key 15
- Witches 15
- Ft 1907r 16
- Icrophon 16
- Keypad 16
- Lamp switch 16
- Lock switch 16
- P1 p2 p3 p4 buttons 16
- Ptt switch 16
- Up dwn button 16
- Witches 16
- Ant coaxial socket 17
- Ext sp jack 17
- Ft 1907r 17
- Onnectors 17
- V dc cable pigtail 17
- Ft 1907r 18
- Peration 18
- Direct keypad frequency entry 19
- Ft 1907r 19
- Peration 19
- Scanning 19
- Tuning dial 19
- Changing the transmitter power level 20
- Ft 1907r 20
- Peration 20
- Dvance 21
- Ft 1907r 21
- Peration 21
- Dvance 22
- Ft 1907r 22
- Peration 22
- Dvance 23
- Ft 1907r 23
- Peration 23
- Epeate 24
- Ft 1907r 24
- Peration 24
- Epeate 25
- Ft 1907r 25
- Peration 25
- Ctcss dcs epcs 26
- Ft 1907r 26
- Peration 26
- Ctcss dcs epcs 27
- Ft 1907r 27
- Peration 27
- Ctcss dcs epcs 28
- Ft 1907r 28
- Peration 28
- Ctcss dcs epcs 29
- Ft 1907r 29
- Peration 29
- Ctcss dcs epcs 30
- Ft 1907r 30
- Peration 30
- Storing the ctcss tone pairs for epcs operation 30
- Activating the enhanced paging code squelch system 31
- Ctcss dcs epcs 31
- Ft 1907r 31
- Paging answer back 31
- Peration 31
- Ctcss dcs epcs 32
- Ft 1907r 32
- Peration 32
- Ctcss dcs epcs 33
- Ft 1907r 33
- Peration 33
- Ft 1907r 34
- Peration 34
- To load dtmf autodialer memories use the following procedure 34
- Ft 1907r 35
- Peration 35
- To transmit the memorized telephone number use the following procedure 35
- Ft 1907r 36
- Peration 36
- Ft 1907r 37
- Peration 37
- Ft 1907r 38
- Memory recall from the microphone s keypad 38
- Peration 38
- Ft 1907r 39
- Peration 39
- Ft 1907r 40
- Peration 40
- Assigning memories to a memory bank 41
- Ft 1907r 41
- Memory bank recall 41
- Peration 41
- Changing a memory bank s name 42
- Ft 1907r 42
- Peration 42
- Removing memories from a memory bank 42
- Ft 1907r 43
- Peration 43
- Ft 1907r 44
- Peration 44
- Peration 45
- Canning 46
- Ft 1907r 46
- Canning 47
- Ft 1907r 47
- Canning 48
- Ft 1907r 48
- Canning 49
- Ft 1907r 49
- Canning 50
- Ft 1907r 50
- Canning 51
- Ft 1907r 51
- Canning 52
- Ft 1907r 52
- Priority revert mode 52
- Canning 53
- Ft 1907r 53
- Ft 1907r 54
- Peration 54
- Setting the smart search mode 54
- Ft 1907r 55
- Peration 55
- Storing smart search memories 55
- Eature 56
- Ft 1907r 56
- Nterne 56
- Onnectio 56
- Programming the frg code 56
- Eature 57
- Ft 1907r 57
- Nterne 57
- Onnectio 57
- Operation accessing an frg node 57
- Eature 58
- Ft 1907r 58
- Nterne 58
- Onnectio 58
- Basic art 59
- Ft 1907r 59
- Ransponde 59
- Setup and operation 59
- Utomati 59
- Arts alert beep options 60
- Arts polling time options 60
- Ft 1907r 60
- Ransponde 60
- Utomati 60
- Cw identifier setup 61
- Ft 1907r 61
- Ransponde 61
- Utomati 61
- Eature 62
- Ft 1907r 62
- Rainin 62
- Ft 1907r 63
- Peration 63
- Ettings 64
- Ft 1907r 64
- Iscellaneou 64
- Ettings 65
- Ft 1907r 65
- Iscellaneou 65
- Ettings 66
- Ft 1907r 66
- Iscellaneou 66
- Ettings 67
- Ft 1907r 67
- Iscellaneou 67
- Ettings 68
- Ft 1907r 68
- Iscellaneou 68
- Ettings 69
- Ft 1907r 69
- Iscellaneou 69
- Ft 1907r 70
- Rocedure 70
- Ft 1907r 71
- Loning 71
- Ft 1907r 72
- The ft 1907r set menu mode already described in parts of many previous chapters is easy to activate and set it may be used for configuration of a wide variety of transceiver parameters some of which have not been detailed previously use the following procedure to activate the set menu mode 1 press and hold in the mhz set key for one second to enter the set mode 2 rotate the dial knob to select the menu item to be adjusted 3 press the mhz set key momentarily to enable adjustment of the selected menu item then rotate the dial knob to perform the actual adjustment 4 after completing your selection and adjustment press and hold in the mhz set key for one second to exit the set mode and resume normal operation 72
- Ft 1907r 73
- Peratin 73
- Ctcss dcs epcs 74
- Ft 1907r 74
- Ft 1907r 75
- Ft 1907r 76
- Ft 1907r 77
- Ft 1907r 78
- Ft 1907r 79
- Ft 1907r 80
- Ft 1907r 81
- Ft 1907r 82
- Ft 1907r 83
- Ft 1907r 84
- Copyright 2011 vertex standard co ltd all rights reserved 88
- No portion of this manual may be reproduced without the permission of vertex standard co ltd 88
- Printed in china 88
Похожие устройства
- Yaesu FT-1DR Инструкция по эксплуатации
- Yaesu FT-250/FNB-83/VAC-10 Инструкция по эксплуатации
- Yaesu FT-252 Инструкция по эксплуатации
- Yaesu FT-257 Инструкция по эксплуатации
- Yaesu FT-25R Инструкция по эксплуатации
- Yaesu FT-270R Инструкция по эксплуатации
- Yaesu FT-2900R Инструкция по эксплуатации
- Yaesu FT-2980R Инструкция по эксплуатации
- Yaesu FT-5DR Инструкция по эксплуатации
- Yaesu FT-65 Инструкция по эксплуатации
- Yaesu FT-70DR Инструкция по эксплуатации
- Yaesu FT-7800R Инструкция по эксплуатации
- Yaesu FT-7900R Инструкция по эксплуатации
- Yaesu FT-818ND Инструкция по эксплуатации
- Yaesu FT-847 Инструкция по эксплуатации
- Yaesu FT-8800R Инструкция по эксплуатации
- Yaesu FT-8900R Инструкция по эксплуатации
- Yaesu FT-891 Инструкция по эксплуатации
- Yaesu FT-991 Инструкция по эксплуатации
- Yaesu FT-991A Инструкция по эксплуатации