Home
Главная
Haier
Стиральные Машины
HWM110-287S
Инструкция по эксплуатации Страница: 11

Haier HWM110-287S [11/18] Ï µ ó ð ë ö ª

Ï´µÓÐëÖª

Midway spinning

Push

Proper Proper

Outer cover of

The spin tub

Inner cover of

The spin tub

The laundries

are slanting

Gland

No gland

(1) Set the water-filling selector control

rod at the "SPIN" side. Fill water for

about 1 minute.

If the water quantity filled is too large,

the water may flow out from the wash

tub side. Please twist the water tap to

limit the water filling.

(2) Close the outer cover of the spin tub.

Spin for 1-2 minutes.

1.Put the laundries into the spin tub evenly and smoothly.

2.Spin

(1) Put the gland in properly.

Please put in the gland properly even if the

laundries quantity is small.

(2) Close the inner and outer cover of the spin tub.

(3) Spin for 1-2 minutes.

3.Run the foam-removing spinning.

SPIN

WASH

Содержание

Ò³ãæ 1 1
Contents 2
Ò³ãæ 2 2
Forbidding sign 3
Meaning and description of the symbols 3
Names of the parts 3
Warning sign 3
º ó ç 3
Ò³ãæ 3 3
Safety precautions 4
Ò³ãæ 4 4
Safety precautions 5
Ò³ãæ 5 5
If the extra hose is too long cut it either at point a or b 6
Installation and adjustment 6
Usage of the drain hose 6
Ò³ãæ 6 6
Figure 1 figure 2 7
Figure 1 indicates the ex factory installation position of the drain hose 7
Figure 3 7
Figure 4 7
How to change the direction of the drain hoses 7
Insert the water inlet hose into the water filling entrance on the control pane directly pull it out to dismantle it 7
Install the two drain hose fixing hooks taken out into the installation hole at the other side of the base frame to aim at the installation hole accurately you can lean the washing machine forward slightly then rotate for 90 as per figure 4 7
Install the water inlet hose select the water level 7
Maximum 7
Medium 7
Minimum 7
Select water level according to the quantity of the laundries set the water level adjusting lever to needed line 7
Take off the drain hose from the hanging hole of the cabinet pull the drain hose fixing hook outwards gently to take out the drain hose from the two fixing hooks as per figure 2 7
Take out the drain hose from the fixing hook extend it from the rear side when the drain hose is extended from the rear side it can be hung on the point for drain hose at the two sides of the cabinet see to figure 6 7
Then hang the drain hose into the hanging hole at the spin tub side as per figure 5 7
Water inlet 7
Water inlet hose 7
Water level indicator 7
Ò³ãæ 7 7
A check if the laundries are applicable for washing with machine b divide the laundries that are not colorfast from other laundries c put those laundries difficult to absorb water into water with hand d for those laundries with heavy soil please first remove the dirt like mud or dust for the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil e for those laundries that may get lint ball and those with long fur turn it over before putting in f do not put those laundries polluted by chemicals into the washing machine directly 8
Pay attention to followings before washing the laundries 8
Preparation before washing 8
Ò³ãæ 8 8
How to use the washing powder 9
The musts in washing 9
Usage of the detergent 9
Ò³ãæ 9 9
Washing sequence 10
Ò³ãæ 10 10
Midway spinning 11
Ï µ ó ð ë ö ª 11
Ò³ãæ 11 11
Rinse with stored water 12
Rinse with water filling 12
Rinsing 12
Ò³ãæ 12 12
Spinning 13
To do spinning and draining or rinsing with water filling together please first do spinning for around 1 minute then do draining or rinsing with water filling otherwise the spinning will stop owing to too much water stored in the spin tub 13
Ò³ãæ 13 13
Cleaning the lint filter 14
Cleaning the overflow filter 14
Disposal after washing 14
Ò³ãæ 14 14
Cleaning the overflow filter 15
Cleaning the overflow filter clean the lint around the filter and flush with tap water 15
Corrugation pipe 15
Disposal of the complete unit 15
Figure 1 15
Figure 2 15
Install the overflow filter 1 install the corrugation pipe 2 insert the mounting plate at the bottom of the filter into the valve cover 3 hang up the hook at the left upper side 4 push the upper part in as indicated in figure 2 15
Take off the corrugation pipe dismantle the upper part of the corrugation pipe inside the overflow filter as indicated in figure 1 15
Water level adjusting lever 15
Ò³ãæ 15 15
Trouble shooting answer to question 16
When the remained water is frozen 16
Ò³ãæ 16 16
Phenomena the reason 17
Trouble shooting answer to question 17
Ò³ãæ 17 17
Packing list 18
Speciafication 18
Ò³ãæ 18 18

Haier HWM110-287S [11/18] Ï µ ó ð ë ö ª

Содержание

Похожие устройства