![Haier HKS800TXME [6/10] Troubleshooting](/img/pdf.png)
Haier HKS800TXME [6/10] Troubleshooting
![Haier HKS800TXME [6/10] Troubleshooting](/views2/1827385/page6/bg6.png)
13
Troubleshooting
The following circumstances do not constitute problems. Do not contact the maintenance service
until the problem has been confirmed.
Problem Possible cause
The washing m achine fail s to operate
Poor connection to power supply
Power failure
Door is not properly closed (It will show E1)
Machine has not been switched on
Washing machine cannot be filled
with water
Water tap is n ot turned o n (It will show E5)
Water pressure is less than 0.05Mpa
The inlet hose is kinked
Water supply failure
The program dial is not properly set
The door is not properly closed
The inlet hose filter is blocked
The machine is draining while is
being filled
The height of the drainage hose is below 80cm (it
should be within 80-100cm)
The drainage hose end is in water
Drainage failure
Drainage hose is blocked (It will show E2)
Drainage hose end is exceed 100cm above the floor
level
Thefilterisblocked
Strong vibration during spin drying
Not all packing bolts have been removed
Washingmachineislocatedonanunevensurface
Machine load is over 5kg.
Not all foam packing has been removed from the motor
Operation stops before completion
of a wash cycle
Waterorelectricityfailure
Washing machine is in soak cycle
Operation stops for a period of time
Washing machine is in soak cycle
Washing machine gives an error message.
Excessivefoaminthedrum,which
is spilled to the distribution drawer
The detergent is not a low-foaming type or for manual
wash
Excessive use of detergent
4
ƽ
Remove all the packing materials (including the
foam base)to prevent vibration during use, as
shown in Fig.1.Upon opening of the package,
water drops may be seen on the plastic bag and
the porthole. This is normal phenomenon resulting
from water test in the factory.
Fig
.1
ƽ
Check attachments and materials with reference to the following
ƽ
Dismantle the packing bolts as shown in Fig. 2.
The packing bolts are designed for clamping anti-vibration components
inside of the washing machine during the transportation process.
Before use:
1. Remove the back plate;
2. Remove the three packing bolts on the back plate and take out the
rubber hose;
3. Replace the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: The packing bolts and rubber hose should be kept in a safe
place for later use)
Fig.3
ƽ
Adjusting the washing machine
There are adjustable feet under the bottom of the washing machine. Before
use, the washing machine should be adjusted, as shown in Fig. 3, so that it
is level.
Fig.2
Model
HKS1200TXVE/ME
HKS1000TXVE/ME
HKS800TXVE/ME
Qty
Name
Operation
manual
1
1
1
1
3
Quality
certificate
Water
hose
Drainage
holder
Plastic
plugs
Installation
Содержание
- Automatic drum washing machine 1
- Hks1200txve me hks1000txve me hks800txve me 1
- Operation manual 1
- Table of contents 1
- Caution and warning symbols 2
- For you safely any instructions in this manual with this warning sign must be followed strictly 2
- For your safety and to prevent damage to the washing machine any instructions in this manual with this stop sign must be followed strictly 2
- Name of parts 2
- This diagram may be slightly different from the layout of the washing machine you have just purchased due to techincal improvements 2
- Matters needing attention 3
- Safety 3
- Adjustable thermostat 4
- Dear customer for the machine and your own security do not repair it by yourself do not use the washing machine which some parts are lost 4
- Door lock 4
- Drain pump 4
- During installation ensure that the electric cable is not trapped by the washing machine and avoid damage to the electric cable 4
- During use 4
- Economic wash switch 4
- Hks1200txve me hks1000txve me hks800txve me 4
- Keep away from heat sources and direct sunlight to prevent plastic and rubber components from aging 4
- Matters needing attention 4
- Openings in the base of the washing machine 4
- Power switch 4
- Pressure switch heating element 4
- The carpet must not obstruct the ventilation 4
- The washing machine should not be installed outdoors or in a damp place in the event of water leakage or splashes allow the machine to dry naturally 4
- Wiring circuit 4
- Matters needing attention 5
- Technical specifications 5
- Adjusting the washing machine 6
- Being filled 6
- Check attachments and materials with reference to the following 6
- Installation 6
- Of a wash cycle 6
- Problem possible cause 6
- Should be within 80 100cm 6
- Troubleshooting 6
- With water 6
- During operation 1 collect clothes for one full wash load 2 do not overload the washing machine 3 pre wash heavily soiled clothes 4 reduce the amount of detergent or choose standard or delicate wash programs for slightly soiled clothes 5 choose a proper washing temperature only exceed 6 8
- For heavily soiled clothes 6 do not use more detergent than required 7 softening agent makes clothes feel softer and easier to iron 8
- Hints for saving energy 8
- Operational functions 8
- Press this button the laundry will be fluffed up at the end of the spinning cycle to reduce wrinkles 8
- For pre washing program detergent should be added to both compartments 1 and 2 compartment 2 allows only solid detergents for other programs do not add detergent to compartment 1 2 do not overuse softener otherwise it will damage the artificial fibers refer to the instructions during use 9
- Functions 9
- Load reference 9
- Notes 1 when first using the washing machine let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine 2 do not overload the washing machine 9
- Open the door put in the laundry piece by piece close the door tightly 9
- Slide out the detergent drawer and put the required detergent and softening agent into the corresponding boxes push back the drawer gently caution 9
- To get the best washing effect an appropriate washing program should be selected according to the laundry type note the above operations refer to conditions without power off memory or the washing machine will continue operation from where the program was broken to clear memory press the start pause button turn off the power for a few seconds and turn on again all the settings will be renewed 9
- Washing procedure 9
- Indicates that i 10
- Pre wash is selected detergent must be added 10
- Preparation 10
- Program description table 10
- Wash load 10
Похожие устройства
- Haier HK1407I Инструкция по эксплуатации
- Haier HK1407IME Инструкция по эксплуатации
- Haier HK1207I Инструкция по эксплуатации
- Haier HK1207IME Инструкция по эксплуатации
- Haier HK1007I Инструкция по эксплуатации
- Haier HK1007IME Инструкция по эксплуатации
- Haier HK807I Инструкция по эксплуатации
- Haier HK807IME Инструкция по эксплуатации
- Heat Plus ECO SPN-202 Instruction manual
- Heat Plus ECO SPN-204 Instruction manual
- Heat Plus ECO SPN-205 Инструкция по эксплуатации
- Heat Plus ECO SPN-206 Инструкция по эксплуатации
- Heat Plus ECO SPN-208 Инструкция по эксплуатации
- Heat Plus ECO SPN-210 Инструкция по эксплуатации
- Heat Plus Standart SPN-305-030 Инструкция по эксплуатации
- Heat Plus Standart SPN-310-120 Инструкция по эксплуатации
- Haier HK1407TVE Инструкция по эксплуатации
- Haier HK1407TME Инструкция по эксплуатации
- Haier HK1207TVE Инструкция по эксплуатации
- Haier HK1207TME Инструкция по эксплуатации