![Haier HK800TXME [6/10] Adjusting the washing machine](/img/pdf.png)
Haier HK800TXME [6/10] Adjusting the washing machine
![Haier HK800TXME [6/10] Adjusting the washing machine](/views2/1827415/page6/bg6.png)
13
Troubleshooting
The following circumstances do not constitute problems. Do not contact the maintenance service
until the
problem has been confirmed.
Problem Possible cause
The w ashing m achine fail s to operate
Poor connection to power supply
Power failure
Door is not properly closed (It will show E1)
Machine has not been switched on
Washing machine cannot be filled
with water
Water tap is not turned on(It will show E5)
Water pressure is less than 0.05Mpa
The inlet hose is kinked
Water supply failure
The program dial is not properly set
The door is not properly closed
The inlet hose filter is blocked
The machine is draining while is
being filled
The height of the drainage hose is below 80cm (it
should be within 80-100cm)
The drainage hose end is in water
Drainage failure
Drainage hose is blocked (It will show E2)
Drainage hose end is below 100cm above the floor
level
Thefilterisblocked
Strong vibration during spin drying
Not all packing bolts have been removed
Washingmachineislocatedonanunevensurface
Machine load is over 6kg.
Not all foam packing has been removed from the motor
Operation stops before completion
of a wash cycle
Waterorelectricityfailure
Washing machine is in soak cycle
Operation stops for a period of time
Washing machine is in soak cycle
Washing machine gives an error message.
Excessivefoaminthedrum,which
spilled to the distribution drawer
The detergent is not a low-foaming type or for manual
wash
Excessive use of detergent
4
ƽ
Remove all the packing materials (including the
foam base)to prevent vibration during use, as
shown in Fig.1.Upon opening of the package,
water drops may be seen on the plastic bag and
the porthole. This is normal phenomenon resulting
from water test in the factory.
Fig.1
ƽ
Check attachments and materials with reference to the following
ƽ
Dismantle the packing bolts as shown in Fig. 2.
The packing bolts are designed for clamping anti-vibration components
inside of the washing machine during the transportation process.
Beforeuse:
1. Remove the back plate;
2. Remove the three packing bolts on the back plate and take out the
rubber hose;
3. Replace the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: The packing bolts and rubber hose should be kept in a safe
place for later use)
Fig.3
ƽ
Adjusting the washing machine
There are adjustable feet under the bottom of the washing machine. Before
use, the washing machine should be adjusted, as shown in Fig. 3, so that it
is level.
Fig.2
Model
HK1600TXVE/ME
HK1400TXVE/ME
Qty
Name
Operation
manual
1
1
1
1
4
Quality
certificate
Water
hose
Drainage
holder
Plastic
plugs
Installation
HK1200TXVE/ME
HK1000TXVE/ME
HK800TXVE/ME
1
1
1
1
3
Содержание
- Automatic drum washing machine 1
- Hk1600txve me hk1400txve me hk1200txve me hk1000txve me hk800txve me 1
- Operation manual 1
- Table of contents 1
- Caution and warning symbols 2
- For you safely any instructions in this manual with this warning sign must be followed strictly 2
- For your safety and to prevent damage to the washing machine any instructions in this manual with this stop sign must be followed strictly 2
- Name of parts 2
- This diagram may be slightly different from the layout of the washing machine you have just purchased due to techincal improvements 2
- Keep children away from the packing materials after unpacked 3
- Matters needing attention 3
- Safety 3
- Adjustable thermostat 4
- Door lock 4
- Drain pump 4
- During installation ensure that the electric cable is not trapped by the washing machine and avoid damage to the electric cable 4
- During use 4
- Economic wash switch 4
- Hk1200txve me hk1000txve me hk800txve me 4
- Hk1600txve me hk1400txve me 4
- Keep away from heat sources and direct sunlight to prevent plastic and rubber components from aging 4
- Keep the door slightly open when the washing machine is not in use to prevent formation of odors do not cover the washing machine with plastic cover so that inside dampness cannot be kept in 4
- Matters needing attention 4
- Openings in the base of the washing machine 4
- Power switch 4
- Pressure switch heating element 4
- The carpet must not obstruct the ventilation 4
- The washing machine should not be installed outdoors or in a damp place in the event of water leakage or splashes allow the machine to dry naturally 4
- Use the new hose and the old hose should not be reused 4
- Vh2 vh2 4
- Wiring circuit 4
- Matters needing attention 5
- Technical specifications 5
- The european standards can be met when default settings for intensive wash of cotton fabrics at the maximum speed are selected 5
- Adjusting the washing machine 6
- Check attachments and materials with reference to the following 6
- Installation 6
- Problem possible cause 6
- Troubleshooting 6
- Hints for saving energy 8
- Operational functions 8
- For pre washing program detergent should be added to both compartments 1 and 2 compartment 2 allows only solid detergents for other programs do not add detergent to compartment 1 2 do not overuse softener otherwise it will damage the artificial fibers refer to the instructions during use 9
- Functions 9
- Load reference 9
- Notes 1 when first using the washing machine let it run unloaded for one program to preventthe laundry from being tainted by oil or dirty water from the washing machine 2 do not overload the washing machine 9
- Open the door put in the laundry piece by piece close the door tightly 9
- Slide out the detergent drawer and put the required detergent and softening agent into the corresponding boxes push back the drawer gently caution 9
- To get the best washing effect an appropriate washing program should be selected accord ing to the laundry type note the above operations refer to conditions without power off memory or the washing machine will continue operation from where the program was broken to clear memory press the start pause button turn off the power for a few seconds and turn on again all the settings will be renewed 9
- Washing procedure 9
- If pre wash is selected must add detergent in compartment 1 10
- Preparation 10
- Program description table 10
- Wash load 10
Похожие устройства
- Haier HBF1000TEME Инструкция по эксплуатации
- Haier HA1000TE Инструкция по эксплуатации
- Haier HA800TE Инструкция по эксплуатации
- Haier HA600TE Инструкция по эксплуатации
- Haier HW80-B16636N Инструкция по эксплуатации
- Haier HW70-B14636N Инструкция по эксплуатации
- Haier HW80-B1439NS8 Инструкция по эксплуатации
- Haier HW90-B1439NS8 Инструкция по эксплуатации
- Haier HW100-B1439NS8 Инструкция по эксплуатации
- Haier RWT150AW Сервис мануал
- Haier RWT150AW Инструкция по эксплуатации
- Haier RWT360BW Сервис мануал
- Haier RWT360BW Инструкция по эксплуатации
- Haier GWT560BW Инструкция по эксплуатации
- Haier HW70-B12CIN Инструкция по эксплуатации
- Haier HW80-B14CIN Инструкция по эксплуатации
- Haier HW90-B14CIN Инструкция по эксплуатации
- Haier HW100-B14CIN Инструкция по эксплуатации
- Haier HWF90AN1 Инструкция по эксплуатации
- Haier HWF80AN1 Инструкция по эксплуатации