Kentatsu KMZC20HZAN1 [10/28] Pdf 文件使用 pdffactory pro 试用版本创建 www fineprint cn
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Kentatsu KMZC20HZAN1 [10/28] Pdf 文件使用 pdffactory pro 试用版本创建 www fineprint cn

Kentatsu K4MRC100HZAN1 [10/28] Pdf 文件使用 pdffactory pro 试用版本创建 www fineprint cn
10
Для моделей KMGC35
5
In sta llation Instruction
INDOOR UNIT INSTALLATION
1. Fit the Installation Plate
2. Drill a hole in the wall
Note:
1. Fit the installation plate horizontally
on structural parts of the wall with
spaces around the installation plate.
2. If the wall is made of brick, concrete
or the like, drill eight (8) 5mm diameter
holes in the wall. Insert Plastic Expan-
sion Sheath for appropriate mounting screws.
3. Fit the installatio n plate on the wall with eight
(8) type “A” screws.
Correct orientation
of Instal l ation Plate
Fit the Installation Plate and drill holes in the wall according to the wall structure
and corresponding mounting points on the installa tion plate.
(Dimensions are in “mm” unless otherwise stated)
1. Determine hole positions according to
the diagram as shown above. Drill
one (1 ) hole ( 65mm) slanting slightly
to outdoor side.
2. Always use wall hole conduit when
drilling metal grid, metal plate or the like.
Wall
Indoor
Outdoor
Indoor unit outli ne
12cm or more
to wall
12cm or more
to wall
Left refrigerant
pipe hole 65
φ
Right refrigerant
pipe hole 65
φ
Installation plate
845
15cm or more to ceiling
45
96
Для моделей KMGJ20, KMGJ25, KMGJ35
5
INSTALLATION INSTRUCTIONS
Fig.4
Wall
In door
Outdoor
Fi g.6
Fig.5
Indoor unit installation
2. Drill a hole in the wall
Note:
1. Fit the Installation Plate
1. Fit the installation plate horizontally
on structural parts of the wall with
spaces around the installation plate.
2. If the wall is made of brick, concrete
or the like, drill eight (8) 5mm diameter
holes in the wall.Insert Clip anchor for
appropriate mounting screws.
3. Fit the installation plate on the wall
with eight (8) type “A” screws.
Fit the Installation Plate and drill
ho
les in the wall according to the
wall structure and corresponding
mounting points on the installation
plate.
(Dimensions are in “mm” unless
otherwise stated)
1. Determine hole positions according
to the diagramdetailed in Fig.5. Drill
one (1) hole ( 65mm) slanting slightly
to outdoor side.
2. Always use wall hole conduit when
drilling metal grid, metal plate or the like.
φ
3. Connective Pipe and Drainage
Installation
1. Run the drain hose sloping downward.
Do not install the drain hose as
illustrated in F ig.7.
Dra inage
Fig .7
Do not block water flow by a rise.
Do not put the end of
drain hose into water.
Correct orientation
of Installation Plate
A
Right rear side
refrigerant
pipe hole 65
φ
Installation plate
Indoor unit outline
Left rear side
refrigerant
pipe hole 65
φ
150mm or more to ceiling
120mm or
more to wall
120mm or
more to wall
<12000Btu/h model: (A: 710, B: 250)
>12000Btu/h mode l: (A: 790, B:265)
>18000Btu/h model
90
45
150mm or more to ceiling
Indoor unit outline
Ins tallation plate
Right rear side
refrigerant
pipe hole 65
φ
Left rear side
refrigerant
pipe hole 65
φ
120mm or
more to wall
120mm or
more to wall
920
90
45
80
489
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
Для моделей KMGJ20, KMGJ25: A - 710мм; B - 250мм;
Для моделей KMGJ35: A - 790мм; B - 265мм;
Для моделей KMGJ50
5
INSTALLATION INSTRUCTIONS
Fig.4
Wall
In door
Outdoor
Fi g.6
Fig.5
Indoor unit installation
2. Drill a hole in the wall
Note:
1. Fit the Installation Plate
1. Fit the installation plate horizontally
on structural parts of the wall with
spaces around the installation plate.
2. If the wall is made of brick, concrete
or the like, drill eight (8) 5mm diameter
holes in the wall.Insert Clip anchor for
appropriate mounting screws.
3. Fit the installation plate on the wall
with eight (8) type “A” screws.
Fit the Installation Plate and drill
ho
les in the wall according to the
wall structure and corresponding
mounting points on the installation
plate.
(Dimensions are in “mm” unless
otherwise stated)
1. Determine hole positions according
to the diagramdetailed in Fig.5. Drill
one (1) hole ( 65mm) slanting slightly
to outdoor side.
2. Always use wall hole conduit when
drilling metal grid, metal plate or the like.
φ
3. Connective Pipe and Drainage
Installation
1. Run the drain hose sloping downward.
Do not install the drain hose as
illustrated in F ig.7.
Dra inage
Fig .7
Do not block water flow by a rise.
Do not put the end of
drain hose into water.
Correct orientation
of Installation Plate
A
Right rear side
refrigerant
pipe hole 65
φ
Installation plate
Indoor unit outline
Left rear side
refrigerant
pipe hole 65
φ
150mm or more to ceiling
120mm or
more to wall
120mm or
more to wall
<12000Btu/h model: (A: 710, B: 250)
>12000Btu/h mode l: (A: 790, B:265)
>18000Btu/h model
90
45
150mm or more to ceiling
Indoor unit outline
Ins tallation plate
Right rear side
refrigerant
pipe hole 65
φ
Left rear side
refrigerant
pipe hole 65
φ
120mm or
more to wall
120mm or
more to wall
920
90
45
80
489
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn
2. Если стена кирпичная или бетонная, проделайте в ней отверстия диаметром 5 мм, вставьте в них
дюбели для монтажных болтов.
3. Прикрепите монтажную пластину болтами к стене.
Замечание:
Устанавливайте монтажную пластину и сверлите отверстия в стене, учитывая ее конструкцию и материал.
Соблюдайте указанное положение крепежных отверстий. Размеры на схеме указаны в миллиметрах.

Содержание

Похожие устройства

Скачать