Home
Главная
Stomer
Шуруповерты И Винтоверты
SAD-18Ix2-D
Инструкция по эксплуатации Страница: 7

Stomer SAD-18Ix2-D [7/44] Cordless drill driver

Cordless drill/driver

INTENDED USE

• This tool is intended for drilling in wood, metal, ceramic and

plastic; tools with electronic speed control and left/right ro-

tation are also suitable for screwdriving and thread cutting

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1 Switch for on/off and speed control

2 Switch for changing direction of rotation

3 Keyless chuck

4 Ring for torque control

SAFETY

WARNING! Read all instructions. Failure to follow all instruc-

tions listed below may result in electric shock, ﬁ re and/or seri-

ous injury.

• Ensure the switch is in the off position before inserting bat-

tery pack. Inserting the battery pack into power tools that

have the switch on invites accidents.

• Recharge only with the charger speciﬁ ed by the manufac-

turer. A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another battery

pack.

• Use power tools only with speciﬁ cally designated battery

packs. Use of any other battery packs may create a risk of

injury and ﬁ re.

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before you

start working

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the charger (charg-

ers with a rating of 230V or 240V can also be connected to

a 220V supply)

• In case of electrical or mechanical malfunction, immediate-

ly switch off the tool or unplug charger from power source

• SBM Group can assure ﬂ awless functioning of the tool only

when original accessories are used

• Use only accessories with an allowable speed matching at

least the highest no-load speed of the tool

• This tool should not be used by people under the age of 16

years

• Be careful not to drill or drive into areas where electrical

wires may be contacted

• Ensure that switch (2) is in the middle (locking) position

before making any adjustments or changing accessories

as well as when carrying or storing the tool

• Do not touch the contacts in the charger

• Do not expose tool/charger/battery to rain

• Never charge battery outdoors

• Store tool/charger/battery in locations where temperature

will not exceed 40° C or drop below 0° C

• Batteries will explode in ﬁ re, so do not burn battery for any

reason

• When damaged, and under extreme usage and tempera-

ture conditions, batteries may start to leak

- if liquid comes into contact with the skin, wash quickly with

soap and water, then with lemon juice or vinegar

- if liquid gets into the eyes, ﬂ ush eyes with clean water for

a minimum of 10 minutes and seek immediately medical

attention

• When battery is not in tool or charger, it should be kept

away from metal objects such as nails, screws, keys etc. to

prevent short-circuit

• Do not use charger when damaged; take it to one of the of-

ﬁ cially registered SBM Group Service Stations for a safety

check

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble charger or battery

• Do not attempt to recharge non-rechargeable batteries with

the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire in

the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut off the cord of the charg-

er, it must be disposed of safely and not left unattended

To ensure longer service life and proper perform-

ance of the battery, take the following actions when

you start using new battery:

1. Use the new battery, without recharging it, till its complete

discharge.

2. Then charge the battery for 3-5 hours.

3. Repeat abovementioned actions (1 and 2) 3-5 times to

reach the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when carry-

ing out maintenance work on the motor.

Regularly clean the machine housing with a soft cloth, prefer-

ably after each use. Keep the ventilation slots free from dust

and dirt.If the dirt does not come off use a soft cloth moistened

with soapy water. Never use solvents such as petrol, alcohol,

ammonia water, etc. These solvents may damage the plastic

parts.

The machine requires no additional lubrication.

Should a fault occur, e.g. after wear of a part, please contact

your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during transport,

it is delivered in a sturdy packaging. Most of the packaging

materials can be recycled. Take these materials to the appro-

priate recycling locations. Take your unwanted machines to

your local SBM Group dealer. Here they will be disposed of in

an environmentally safe way.

Ni-Cd batteries can be recycled. Deliver them to a disposal site

for chemical waste so that they can be recycled or disposed of in

an environmentally friendly manner.

Stomer SAD-18Ix2-D [7/44] Cordless drill driver

Содержание

Похожие устройства