Home
Главная
Hander
Шлифовальная Машина
HAG-911
Инструкция по эксплуатации Страница: 2

Hander HAG-911 [2/50] English

Angle grinder

INTENDED USE

This tool is intended for grinding, cutting and deburring

metal and stone materials without the use of water; with

the appropriate accessories the tool can also be used for

brushing and sanding

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1. Spindle

2. Clamping ﬂ ange

3. Spanner

4. Spindle-lock button

5. Auxiliary handle

6. Safety guard

7. Mounting ﬂ ange

8. On/off locking switch

9. Switch locking knob

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁ re

and/or serious injury.

• Only use this tool for dry grinding/cutting

• Only use the ﬂ anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

• Use the original SBM Group accessories which can be

obtained from your SBM Group dealer

• For mounting/using non- SBM Group accessories ob-

serve the instructions of the manufacturer concerned

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Do not use damaged, deformed or vibrating grinding/

cutting discs

• Handle and store grinding/cutting discs carefully to

avoid chipping and cracking

• Protect accessories from impact, shock and grease

• Do not use a grinding/cutting disc that is larger than the

maximum recommended size

• Only use grinding/cutting discs with a hole diameter

which fits mounting flange (7) without play; never use

reducers or adaptors to fit large-hole grinding/cut-

ting discs

• Never use grinding/cutting discs with a threaded hole,

of which the thread is not long enough to accept the

spindle length of the tool

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

• Only use an extension cord which is intended for out-

door use and equipped with a splashproof coupling-

socket

BEFORE USE

• Before using the tool for the ﬁ rst time, it is recommend-

ed to receive practical information

• Do not work materials containing asbestos (asbestos is

considered carcinogenic)

• Take protective measures when during work dust can

develop that is harmful to one’s health, combustible or

explosive (some dusts are considered carcinogenic);

wear a dust mask and work with dust/chip extraction

when connectable

• Be careful of hidden electrical wires or gas- and water

pipes; check the work area, for instance with a metal

detector

• Be careful when cutting grooves, especially in support-

ing walls (slots in supporting walls are subject to coun-

try- speciﬁ c regulations; these regulations are to be ob-

served under all circumstances)

• Clamp the workpiece in case it does not remain stationa-

ry from its own weight

• Do not clamp the tool in a vice

• Use completely unrolled and safe extension cords with

a capacity of 16 Amps (UK 13 Amps)

• Wear protective glasses and gloves, hearing protection

and sturdy shoes; when necessary, also wear an apron

• Always mount auxiliary handle (5) and protective guard

(6); never use the tool without them

• Be sure tool is switched off when plugging in

DURING USE

• Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug;

never use the tool with a damaged cord

• Push spindle-lock button (4) only when spindle (1) is at

a standstill

• Keep hands away from rotating accessories

• When grinding metal, sparks are generated; keep other

persons and combustible material from work area

• In case of electrical or mechanical malfunction, immedi-

ately switch off the tool and disconnect the plug

• In case the cutting disc is blocked, resulting in jerking

forces on the tool, immediately switch off the tool

• In case of current interruption or when the plug is ac-

cidentally pulled out, unlock the on/off switch (8) imme-

diately and put it in the OFF-position in order to prevent

uncontrolled restarting

• Do not apply so much pressure on the tool that it comes

to a standstill

AFTER USE

• Before you put down the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

• After switching off the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

English

Hander HAG-911 [2/50] English

Содержание

Похожие устройства