Hermes Technics HT-RIO-07 (RI61930) [52/64] Installation manual operation test
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hermes Technics HT-RIO-07 (RI61930) [52/64] Installation manual operation test

Hermes Technics HT-RIO-07 (RI61930) [52/64] Installation manual operation test
INSTALLATION MANUAL---Installation of the outdoor unit
The air and humidity left inside the refrigerant circulat-
ion can cause compressor malfunction. After having co-
nnected the indoor and outdoor units, bleed the air and
humidity from the refrigerant circulation using a va-
cuum pump.
Refrigerant flow direction
2-way valve
(6) Open 1/4 turn
valve cap
(1) Turn
(8) Tighten
(2) Turn
3-way valve
(8) Tighten
(1) Turn
(7) Turn to fully
open the valve
(7) Turn to fully
open the valve
(8) Tighten
Service
port nut
Valve cap
(1) Unscrew and remove the caps from the 2 - way and
3-way valves.
(2) Unscrew and remove the cap from the service port.
(3) Connect the vacuum pump hose to the service port.
(4) Operate the vacuum pump for 10 - 15 minutes until
an absolute vacuum of 10 mm Hg has been reached.
(5) With the vacuum pump still in operation , close the
low - pressure knob on the vacuum pump coupling.
Stop the vacuum pump.
(6) Open the 2 - way valve by 1/4 turn and then close it
after10 seconds. Check all the joints for leaks using
liquid soap or an electronic leak device.
(7) Turn the body of the 2-way and 3-way valves.
Disconnect the vacuum pump hose.
(8) Replace and tighten all the caps on the valves.
3-way valve diagram
connect to indoor unit
open position
spindle
service port cap
Connect to
outdoor unit
Valve core
needle
INSTALLATION MANUAL--- operation test
wall
(indoor) (outdoor)
piping
piping
gasket
insulating tape
insulating covering
Clamps
1. Wind insulating covering around the joints of the ind-
oor unit and fix it with insulating tape.
2. Fix the exceeding part of the signal cable to the
piping or to the outdoor unit.
3. Fix the piping to the wall ( after having coated it with
insulating tape) using clamps or insert them into pla-
stic slots.
4. Seal the hole in the wall through which the piping is
passed so that no air or water can fill.
Do the ON/OFF and FAN operate normally?
Does the MODE operate normally?
Do the set point and TIMER function properly?
Does each lamp light normally?
Do the flap for air flow direction operate normally?
Is the condensed water drained regularly?
Is there any abnormal noise or vibration during
operation?
Could the noise , the air flow or the condensed water
drainage disturb the neighbours?
Is there any coolant leakage?
Indoor unit test
Outdoor unit test
Note: the electronic controller allows the compressor to
start only three minutes after voltage has reached
the system.
51
BLEEDING
Indoor unit

Содержание

Похожие устройства

ENGLISH INSTALLATION MANUAL Installation of the outdoor unit BLEEDING The air and humidity left inside the refrigerant circulat ion can cause compressor malfunction After having co nnected the indoor and outdoor units bleed the air and humidity from the refrigerant circulation using a va cuum pump 1 Unscrew and remove the caps from the 2 way and 3 way valves 2 Unscrew and remove the cap from the service port 3 Connect the vacuum pump hose to the service port 4 Operate the vacuum pump for 10 15 minutes until an absolute vacuum of 10 mm 11g has been reached 5 With the vacuum pump still in operation close the low pressure knob on the vacuum pump coupling Stop the vacuum pump 6 Open the 2 way valve by 1 4 turn and then close it afterlO seconds Check all the joints for leaks using liquid soap or an electronic leak device 7 Turn the body of the 2 way and 3 way valves Disconnect the vacuum pump hose 8 Replace and tighten all the caps on the valves llixkx uni Refrigerant flow ditectior 7 Tüni to fully open the valve 8 Tighten INSTALLATION MANUAL operation test Indoor unit test Do the ON OFF and FAN operate normally Does the MODE operate normally Do the set point and TIMER function properly Does each lamp light normally Do the flap for air flow direction operate normally Is the condensed water drained regularly Outdoor unit test Is there any abnormal noise or vibration during operation Could die noise the air flow or the condensed water drainage disturb the neighbours Is there any coolant leakage Note the electronic controller allows the compressor to start only three minutes after voltage has reached the system 51 6 Open 1 4 aim 7 Him to fully ipcii ite valve l nim 2 him 1 Wind insulating covering around die joints of die ind oor unit and fix it with insulating tape 2 Fix the exceeding part of the signal cable to die piping or to the outdoor unit 3 Fix the piping to die wall after having coated it with insulating tape using clamps or insert them into pla stic slots 4 Seal the hole in the wall through which the piping is passed so that no air or water can fill 2 way valve J way valve 8 Tighten

Скачать