Metabo BF 18 LTX (600321850) без акк. и з.у [11/72] Tips and tricks
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Metabo BF 18 LTX (600321850) без акк. и з.у [11/72] Tips and tricks

Metabo BF 18 LTX (600321850) без акк. и з.у [11/72] Tips and tricks
ENGLISH en
11
6.6 Removing and inserting the battery pack
Removal:
Press the battery pack release (13) button and pull
the battery pack (16)
forwards.
Inserting:
Slide in the battery pack (16) until it engages.
7.1 On/Off switch, continuous activation
Always guide the machine with both hands.
Switch the machine on first before mounting it
on the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits.
After switching off the machine, only place it
down when the motor has come to a standstill.
Avoid switching on the machine accidentally:
always switch it off when the battery pack is
removed from the machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine using
the handles provided, stand in a safe position and
concentrate.
Switching on/
Continuous activation
: Push sliding
switch (11) forward. For continuous
activation, now tilt downwards until it
engages.
Switching off: Press the rear end of the slide
switch (11) and release.
7.2 Sanding belt replacement
See illustration B, page 2.
- Manually loosen screw (5) and remove cover (3).
- Pull tensioner arm (7) backwards and remove
sanding belt (6).
- Place the new sanding belt on the rollers such that
its direction of circulation (arrows on the inside of
the sanding belt) matches the arrows (4) on the
cover. Place the sanding belt first on the drive
shaft and then on the roller on the sanding
attachment (1).
- Replace the cover (3) and tighten the screw (5) by
hand.
- Check the belt run and adjust if necessary (see
Section 7.3).
7.3 Adjusting belt run
Using the screw (2), adjust the sanding belt
(while the machine is not in operation and the
battery pack is removed) so that it runs in the centre
of the sanding belt roller.
7.4 Sanding procedure
Switch the machine on first before mounting it on
the workpiece.
Place the machine on the material such that the
sanding belt is parallel to the surface of the
workpiece.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
7.5 Replacing the sanding attachment
See illustration C, page 2.
- Removing the sanding belt (see Section 7.2).
- Remove screw (2), and remove sanding
attachment (1).
- Attach the other sanding attachment as shown
(ensure that the nose at the end of the sanding
attachment is pointing in the direction of the
tensioning arm, see illustration C).
- Secure with screw (2).
- Attaching the sanding belt (see Section 7.2).
- Adjusting the belt run (see Section 7.3).
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
The electronic signal display (12) lights
up and the load speed decreases. The
temperature is too high! Run the machine in
idling until the electronics signal indicator switches
off.
The electronic signal display (12) flashes
and the machine does not start. The restart
protection is active. The machine will not start
if the battery pack is inserted while the machine is
on. Switch the machine off and on again.
Do not press the device too firmly against the
surface being sanded. This does not improve, but
rather impairs, the sanding performance.
For optimum operation: Sand on the side on which
the sanding belt moves towards the machine.
7. Use
0
I
11
8. Cleaning, Maintenance
9. Troubleshooting
10. Tips and Tricks
2

Содержание

Похожие устройства

Скачать