Xiaomi Mi Smart LED Ceiling Light MJXDD01SYL (BHR4118GL) Инструкция по эксплуатации онлайн

Product Overview

Precautions

Make sure the voltage is consistent with the ceiling light's operating voltage before use.

Using the mismatched voltage may damage the ceiling light and cause safety hazards.

The ceiling light generates heat during working. Please keep it is well ventilated for heat

dissipation.

This ceiling light can be controlled by an app or remote control (not included, sold

separately). Turning o the ceiling light by remote control or app does not cut it o from

the electricity, hence, do not touch, replace, or disassemble this ceiling light. Otherwise,

it may cause an electric shock, injury, or even death.

The light installation requires a qualied electrician, and the wiring must comply with

IEEE electrical standards or national standards.

The ceiling light should be installed in a stable location to prevent it from dropping

down or falling o.

Under normal use of condition, this equipment should be kept a separation distance of

at least 20cm between the antenna and the body of the user.

For indoor use only.

Do not replace the light source of the ceiling light by yourself. The light source should

only be replaced by the manufacturer, after-sales service, or a qualied electrician.

Restoring Factory Settings

Read this manual carefully before use, and retain it for future reference.

Note: Try to wiggle the lampshade around to make sure it is properly and rmly installed.

Otherwise, it may fall down.

EU Declaration of Conformity

Hereby, Qingdao Yeelink Information Technology Co., Ltd. declares that the radio

equipment type MJXDD01SYL is in compliance with Directive 2014/53/EU. The full text of

the EU declaration of conformity is available at the following internet address:

https://www.mi.com/en/service/support/declaration.html.

WEEE Disposal and Recycling

All products bearing this symbol are waste electrical and electronic equipment

(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted

household waste. Instead, you should protect human health and the environment

by handing over your waste equipment to a designated collection point for the

recycling of waste electrical and electronic equipment, appointed by the

government or local authorities. Correct disposal and recycling will help prevent

potential negative consequences to the environment and human health. Please

contact the installer or local authorities for more information about the location as

well as terms and conditions of such collection points.

Installation

1. Drill holes

Place the base in the position the ceiling light will be installed, and mark the positions

of the mounting holes, then remove the base. Use a φ6 mm drill to drill holes with a

depth of at least 40 mm, then insert the included four wall plugs into the holes.

Note: Try to wiggle the base around to make sure it is properly and rmly installed.

Otherwise, it may fall down.

Warning: Risk of an electric shock. This ceiling light must be grounded.

Warning: Before installing, replacing or inspecting the ceiling light, cut o

the electricity to prevent an electric shock.

6-8mm

Stripped Wire

Self-tapping Screw

× 4

Wall Plug

Lampshade

Base

Wiring Hole

Mounting Hole

Terminal Block

Connector

Note: Illustrations of product, accessories, and user interface in the user manual are for reference

purposes only. Actual product and functions may vary due to product enhancements.

Connect with Mi Home/Xiaomi Home App

Specications

Model: MJXDD01SYL

Power Factor: >0.9

Operating Temperature: -10°C to 40°C

Operating Humidity: 0–85% RH

Color Temperature: 2700–6000 K

Rated Input: 100–240V～ 50/60Hz Max. 0.5A

Rated Power: 45 W (81 × 1 W/LED module)

Compatible with: Android 4.4 & iOS 9.0 or above

Wireless Connectivity: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz, Bluetooth 4.2 BLE

Operating Frequency:2412-2472 MHz (Wi-Fi) 2402-2480 MHz (BT)

Maximum Output Power: 18.95 dBm (Wi-Fi) 4.81 dBm (BT)

Junction Box

2. Fix the base

Lead the stripped wires through the wiring hole in the base, and then align the

mounting holes with the wall plugs. Screw the included four self-tapping screws into

the wall plugs to x the base onto the ceiling. Make sure the base is securely installed.

3. Connect the stripped wires

The terminal block connector is suitable for wires with a cross-sectional area of

0.75–1.5 mm². Strip about 6–8 mm of the wires, then connect the neutral, ground, and

live wires according to the marks (N, , and L) to the terminal block connector on the

ceiling light. Use a screwdriver to clamp down each line by tightening the screws.

Gently pull each wire to ensure it has been rmly connected.

Note: The wires should run closely along the base in order to avoid shadows on the lampshade. If the

wires are too long, please cut o the excess part.

4. Install the lampshade

Hold both sides of the lampshade and align it with the base, then gently place it onto

the base. Rotate the lampshade clockwise and lock it into the place until the internal

metal part makes a clicking sound.

Product Features

High Color

Rendering Index

Adjustable Brightness

Firmware Update

Smart Scene

Adjustable Color

Temperature

App Remote Control Smart ConnectionVoice Control

Wall Switch Control

1. Remove the light source

The ceiling light contains three light boards and three protective covers. Each light

board is xed to the base with two rivets and each protective cover is xed to the light

board and base with three rivets.

When removing the light source, rst uninstall the three rivets from the protective

Replacing the Light Source

Protective Cover

Protective Cover Rivet

Press down the plastic tip of the rivet

cap about 3 mm, then remove the rivet

bracket to completely remove the rivet.

Press down the plastic tip of the rivet

cap about 3 mm, then remove the rivet

bracket to completely remove the rivet.

Light Board

Light Board Rivet

Warning: Before replacing the LED light board, cut o the electricity to prevent an electric shock.

This replacement should only be carried out by a qualied electrician.

Use the wall switch to turn on and o the ceiling light within 5 seconds, you can change

the color temperature from warm yellow light, white light to night light by default. You

can set the favorite light via the app.

2. Install the light source

Place the light board on the base, and use two new rivets to x the light board onto

the base. Connect the wiring, then install the protective cover on the light board with

three new rivets to x the cover onto the base.

This product works with Mi Home/Xiaomi Home app *. Control your device, and

interact it and other smart home devices with Mi Home/Xiaomi Home app.

Scan the QR code to download and install the app. You will be directed to the

connection setup page if the app is installed already. Or search "Mi Home/Xiaomi

Home" in the app store to download and install it.

* The app is referred to as Xiaomi Home app in Europe (except for Russia). The name of the app

displayed on your device should be taken as the default.

Note: The version of the app might have been updated, please follow the instructions based on the

current app version.

Apple HomeKit Smart Control

1. Open the Home app on your iPhone or iPad.

2. Tap "Add Accessories" and follow the instructions to scan the QR code either on

the back cover of the user manual or on the junction box, or enter the 8-digit setup

code above the QR code to grant the Apple Home app access.

* Make sure a Wi-Fi network with Internet access is available (this product does not support 5 GHz

networks).

To control this HomeKit-compatible accessory, it is recommended that you use iOS 9.0 or above.

The HomeKit setup code is in the user manual and on the junction box, do not lose it.

When adding the product to the Home app after the factory settings are restored, you will need the

HomeKit setup code again.

In case the user manual is lost, remove the lampshade and scan the QR code or enter the setup code

on the junction box.

iPad and iPhone are the trademarks of Apple Inc., and they are registered in the United States and

other countries.

Note: Cycling the three light modes twice and pressing the wall switch again will restore the factory

settings of the ceiling light.

Use the wall switch to turn the ceiling light on and o seven times consecutively (turn

o the ceiling light and wait for two seconds, then turn it on and wait for two seconds,

this counts as one time). The ceiling light then starts breathing and automatically restarts

after ve seconds, and the factory settings of the ceiling light have been restored.

Note: When using the ceiling light in a new network environment, you need to restore the factory

settings and connect to the network again.

cover of the light board, then remove the protective cover of the light board and

unplug the wiring connected to the light board. Finally, uninstall the two rivets from

the light board, and then remove the light board.

Open Mi Home/Xiaomi Home app, tap "+" on the upper right, and then follow prompts

to add your device.

EN EN EN EN

EN EN

Xiaomi Mi Smart LED Ceiling Light MJXDD01SYL (BHR4118GL) Инструкция по эксплуатации онлайн

Содержание

Похожие устройства