![Makita DGA506Z без акк. и з.у [12/16] Operation](/img/pdf.png)
Makita DGA506Z без акк. и з.у [12/16] Operation
![Makita DGA506Z без акк. и з.у [12/16] Operation](/views2/1888814/page12/bgc.png)
12 ENGLISH
For 115 mm (4 - 1/2″) / 125 mm (5″)
model
1
2
3
► 1. Sanding lock nut 2. Abrasive disc 3. Rubber pad
1. Mount the rubber pad onto the spindle.
2. Fit the disc on the rubber pad and screw the sand-
ing lock nut onto the spindle.
3. Hold the spindle with the shaft lock, and securely
tighten the sanding lock nut clockwise with the lock nut
wrench.
To remove the disc, follow the installation procedure in
reverse.
OPERATION
WARNING: It should never be necessary to
force the tool. The weight of the tool applies ade-
quate pressure. Forcing and excessive pressure
could cause dangerous wheel breakage.
WARNING: ALWAYS replace wheel if tool is
dropped while grinding.
WARNING: NEVER bang or hit grinding disc
or wheel onto work.
WARNING: Avoid bouncing and snagging
the wheel, especially when working corners,
sharp edges etc. This can cause loss of control and
kickback.
WARNING: NEVER use tool with wood cutting
blades and other saw blades. Such blades when
used on a grinder frequently kick and cause loss of
control leading to personal injury.
CAUTION: Never switch on the tool when it
is in contact with the workpiece, it may cause an
injury to operator.
CAUTION: Always wear safety goggles or a
face shield during operation.
CAUTION: After operation, always switch off
the tool and wait until the wheel has come to a
complete stop before putting the tool down.
CAUTION: ALWAYS hold the tool rmly with
one hand on housing and the other on the side
handle.
Grinding and sanding operation
Turn the tool on and then apply the wheel or disc to the
workpiece.
In general, keep the edge of the wheel or disc at an
angle of about 15° to the workpiece surface.
During the break-in period with a new wheel, do not
work the grinder in forward direction or it may cut into
the workpiece. Once the edge of the wheel has been
rounded off by use, the wheel may be worked in both
forward and backward direction.
Operation with abrasive cut-off /
diamond wheel
Optional accessory
WARNING: When using an abrasive cut-off
/ diamond wheel, be sure to use only the special
wheel guard designed for use with cut-off wheels.
(In some European countries, when using a diamond
wheel, the ordinary guard can be used. Follow the
regulations in your country.)
WARNING: NEVER use cut-off wheel for side
grinding.
WARNING: Do not "jam" the wheel or apply
excessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
of kickback, wheel breakage and overheating of the
motor may occur.
WARNING: Do not start the cutting operation
in the workpiece. Let the wheel reach full speed
and carefully enter into the cut moving the tool
forward over the workpiece surface. The wheel
may bind, walk up or kickback if the power tool is
started in the workpiece.
WARNING: During cutting operations, never
change the angle of the wheel. Placing side pres-
sure on the cut-off wheel (as in grinding) will cause
the wheel to crack and break, causing serious per-
sonal injury.
WARNING: A diamond wheel shall be oper-
ated perpendicular to the material being cut.
Содержание
- Cordless angle grinder 1
- Intended use 2
- Specifications 2
- Symbols 2
- Vibration 2
- Warning 2
- Ec declaration of conformity 3
- General power tool safety warnings 3
- Save all warnings and instruc tions for future reference 3
- Warning 3
- Cordless grinder safety warnings 4
- Important safety instructions for battery cartridge 6
- Save these instructions 6
- Warning 6
- Caution 7
- Functional description 7
- Indicating the remaining battery capacity 7
- Installing or removing battery cartridge 7
- Save these instructions 7
- Tips for maintaining maximum battery life 7
- Indicating the remaining battery capacity 8
- Overdischarge protection 8
- Overheat protection 8
- Overload protection 8
- Releasing protection lock 8
- Tool battery protection system 8
- Accidental re start preventive function 9
- Automatic speed change function 9
- Caution 9
- Electric brake 9
- Electronic torque control function 9
- Notice 9
- Shaft lock 9
- Soft start feature 9
- Switch action 9
- Assembly 10
- Caution 10
- For tool with clamp lever type wheel guard 10
- For tool with locking screw type wheel guard 10
- Installing or removing wheel guard for depressed center wheel flap disc flex wheel wire wheel brush abrasive cut off wheel diamond wheel 10
- Installing side grip handle 10
- Warning 10
- Caution 11
- For 100 mm 4 model 11
- Installing or removing abrasive disc 11
- Installing or removing depressed center wheel or flap disc 11
- Installing or removing flex wheel 11
- Warning 11
- Caution 12
- For 115 mm 4 1 2 125 mm 5 model 12
- Grinding and sanding operation 12
- Operation 12
- Operation with abrasive cut off diamond wheel 12
- Warning 12
- Caution 13
- For 100 mm 4 model 13
- For 115 mm 4 1 2 125 mm 5 model 13
- Mm 5 8 16 mm 5 8 13
- Operation with wire cup brush 13
- Air vent cleaning 14
- Caution 14
- Maintenance 14
- Notice 14
- Operation with wire wheel brush 14
- Caution 15
- English 15
- If you need any assistance for more details regarding these accessories ask your local makita service center makita genuine battery and charger 15
- Note 1 in some european countries when using a diamond wheel the ordinary guard can be used instead of the special guard covering the both side of the wheel follow the regulations in your country 15
- Note some items in the list may be included in the tool package as standard accessories they may differ from country to country 15
- Optional accessories 15
- These accessories or attachments are recommended for use with your makita tool spec ified in this manual the use of any other accessories or attachments might present a risk of injury to persons only use accessory or attachment for its stated purpose 15
- 11 8 sumiyoshi cho anjo aichi 446 8502 japan 16
- Jan baptist vinkstraat 2 3070 kortenberg belgium 16
- Makita corporation 16
- Makita europe n v 16
- Www makita com 16
Похожие устройства
- Makita DHR202Z без акк. и з.у Инструкция по эксплуатации
- Makita DJV181Z без акк. и з.у Инструкция по эксплуатации
- Makita DLS714Z без акк. и з.у Инструкция по эксплуатации
- Makita DTW190Z без акк. и з.у Инструкция по эксплуатации
- Makita HP332DZ без акк и з.у Инструкция по эксплуатации
- Зубр Мастер ЗПТ-190-1100 Л Инструкция по эксплуатации
- Зубр Мастер ЗПТ-255-1800 ЛМ2 Инструкция по эксплуатации
- Зубр Мастер ЗПТ-255-1800 ПЛ Инструкция по эксплуатации
- Dewalt DWE492KS Инструкция по эксплуатации
- BLACK & DECKER KA310 Инструкция по эксплуатации
- BLACK & DECKER KA300 Инструкция по эксплуатации
- BLACK & DECKER KG1202 Инструкция по эксплуатации
- AEG 413175 BHO 18/0 без акк. и з.у Инструкция по эксплуатации
- 3dкрестики Profi 1,5 мм 100 шт. К00006582 Инструкция по эксплуатации
- BLACK & DECKER BDCDC18K Инструкция по эксплуатации
- Makita DGA504ZX2 без акк. и з.у Инструкция по эксплуатации
- Makita DPJ180Z без акк. и з.у Инструкция по эксплуатации
- Makita DTW1001Z без акк. и з.у Инструкция по эксплуатации
- Bosch PKS 18 LI (06033B1302) Инструкция по эксплуатации
- Metabo GB 18 LTX BL Q I (603827840) без акк и з.у Инструкция по эксплуатации