Makita SD100DZ без акк. и з.у [8/48] Assembly

Makita SD100DZ без акк. и з.у [8/48] Assembly
8 ENGLISH
Type of saw blade Max. cutting depth
For drywall 30 mm
For wood 15 mm
LED light
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keeps on lighting while the switch trigger is being pulled.
Thelampgoesoutapproximately10secondsafter
releasing the trigger.
►Fig.6: 1. Lamp
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing the dust collector
CAUTION: Never operate the tool without the
dust collector. Dust may come into your eyes and
causeeyeinjury.
Toremovethedustcollector,holdthetoolhandleand
pull back the tabs on the tool. Be sure to pull the tabs on
the both sides at the same time.
►Fig.7: 1.Tab
When installing, align the dust collector's edge with the
groove on the base.
►Fig.8: 1. Groove
Replacing drywall saw blade
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and/or blade
holder.Failuretodosomaycauseinsufcienttight-
ening of the blade, resulting in a serious personal
injury.
CAUTION: Do not touch the blade or the
workpiece immediately after operation.Theymay
be extremely hot and could burn your skin.
CAUTION: Make sure that the blade is prop-
erly secured. Insufcienttighteningoftheblademay
causebladebreakageorseriouspersonalinjury.
1. Remove the dust collector.
2. Remove the bolts on the blade holder with the hex
wrench.
►Fig.9: 1. Bolts 2. Blade holder 3. Blade
3. Setanewbladeasshowninthegure.Makesure
that the curved edge of the blade points forward. Fit the
protrusion of the blade holder into the slot on the blade.
►Fig.10: 1. Slot 2.Protrudedportion(oppositeside)
4. Adjustthecuttingdepththentightenthebolts.
5. Attachthedustcollector.
Installing snap-off blade
CAUTION: Always use the snap-off blade with
designated length, width, and thickness.Aninap-
propriatelyinstalledsnap-offbladecanbebroken.A
brokenbladecanyoffandcauseapersonalinjury.
Asnap-offbladecanalsobeusedwiththistool.Use3
segments of 18 mm wide snap-off blade with 0.5 mm
thickness.Themaximumcuttingdepthis12.5mm
when cutting a drywall.
►Fig.11: 1.Threesegmentsofsnap-offblade
1. Loosentheboltsonthebladeholder.Turnthe
blade holder so that its protrusion faces outward.
2. Insertthesnap-offbladesothatthesharpedge
faces forward.
3. Secure the snap-off blade at the position where
theendoftherstsegmentcomestotheedgeofblade
holder as illustrated.
►Fig.12: 1. Blade holder 2.Endoftherstsegment
of snap-off blade 3.Allowablecuttinglength
Attaching blade cap
CAUTION: Always attach the blade cap when
tool is not used.Abareblademaycausepersonal
injuryordamagetothebladeitself.
Passthebladecapthroughthebladeuntilthehook
catches the base cover. Note the direction of the blade
cap when attaching; the wider hook comes front side.
When removing the blade cap, lift it while pinching the
both sides.
►Fig.13: 1. Blade cap 2. Hook
During operation, insert the blade cap to the hook on
the base as illustrated until it clicks.
►Fig.14: 1. Blade cap 2. Hook
Hex wrench storage
When not in use, store the hex wrench as shown in the
guretokeepitfrombeinglost.
►Fig.15: 1. Hex wrench
Connecting a vacuum cleaner
CAUTION: Attach the blade cap before con-
necting vacuum cleaner.
Connect a Makita vacuum cleaner for clean operation.
Remove the rubber cap on the dust collector and con-
nect the vacuum cleaner's hose to the nozzle of the
dust collector.
►Fig.16: 1. Dust collector 2. Rubber cap 3. Vacuum
cleaner hose

Содержание

Похожие устройства

Скачать