Makita M0801K [5/16] Installing or removing drill bit
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita M0801K [5/16] Installing or removing drill bit

Makita M0801 [5/16] Installing or removing drill bit
5 ENGLISH
FUNCTIONAL
DESCRIPTION
Switch action
CAUTION:
• Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
• Switch can be locked in "ON" position for ease
of operator comfort during extended use. Apply
caution when locking tool in "ON" position and
maintain rm grasp on tool.
► Fig.1: 1. Switch trigger 2. Lock button
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop. For contin-
uous operation, pull the switch trigger, push in the lock
button and then release the switch trigger. To stop the
tool from the locked position, pull the switch trigger fully,
then release it.
Reversing switch action
CAUTION:
• Always check the direction of rotation before
operation.
• Use the reversing switch only after the tool
comes to a complete stop. Changing the direc-
tion of rotation before the tool stops may dam-
age the tool.
• If the switch trigger can not be depressed, check
to see that the reversing switch is fully set to
the
position (A side) or the position (B
side).
► Fig.2: 1. Reversing switch lever
This tool has a reversing switch to change the direc-
tion of rotation. Move the reversing switch lever to
the
position (A side) for clockwise rotation or to
the position (B side) for counterclockwise rotation.
Selecting the action mode
CAUTION:
• Always slide the action mode changing lever all
the way to your desired mode position. If you
operate the tool with the lever positioned half-
way between the mode symbols, the tool may
be damaged.
► Fig.3: 1. Action mode changing lever
This tool has an action mode changing lever. For rota-
tion with hammering, slide the action mode changing
lever to the right (
symbol). For rotation only, slide
the action mode changing lever to the left ( symbol).
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Installing side grip (auxiliary handle)
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the side
grip.
► Fig.4: 1. Grip base 2. Teeth 3. Side grip (auxiliary
handle) 4. Protrusion 5. Loosen 6. Tighten
Always use the side grip to ensure operating safety.
Install the side grip so that the teeth on the grip t in
between the protrusions on the tool barrel.
Then tighten the grip by turning clockwise at the desired
position. It may be swung 360° so as to be secured at
any position.
NOTE: The side grip cannot swing 360° when the
depth gauge is installed.
Installing or removing drill bit
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
► Fig.5: 1. Drill chuck 2. Chuck key
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly. To remove the bit,
turn the chuck key counterclockwise in just one hole,
then loosen the chuck by hand.
After using the chuck key, be sure to return it to the
original position.
Depth gauge (optional accessory)
► Fig.6: 1. Side grip 2. Depth gauge 3. Grip base
4. Hex bolt
The depth gauge is convenient for drilling holes of
uniform depth. Install the depth gauge by the following
sequence.
1. Turn the side grip counterclockwise to loosen the
hex bolt.
2. Insert the depth gauge and adjust the depth of
hole.
3. Turn the side grip clockwise so that the depth
gauge and the grip base are xed on the tool
completely.
NOTE: The depth gauge cannot be used at the posi-
tion where the depth gauge strikes against the tool
body.

Содержание

Похожие устройства

Скачать