Gigabyte Z690 AORUS PRO — supplier's Declaration of Conformity and Compliance Information [44/48]
Превью страниц
Страница 44 /
48
![Gigabyte Z690 AORUS PRO [44/48] United states of america federal communications commission statement](/views2/1918802/page44/bg2c.png)
- 44 -
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Product Name: Motherboard
Trade Name: GIGABYTE
Model Number: Z690 AORUS PRO/Z690 AORUS PRO DDR4
Responsible Party – U.S. Contact Information: G.B.T. Inc.
Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Regulatory Notices
United States of America, Federal Communications Commission Statement
Antenna use:
In order to comply with FCC RF exposure limits, low gain integrated
antennas should be located at a minimum distance of 7.9 inches (20 cm)
or more from the body of all persons.
Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (such as a wireless network
device) near unshielded blasting caps or in an explosive environment
unless the device has been modied to be qualied for such use.
Antenna Warning
The wireless adapter is not designed for use with high-gain antennas.
Use On Aircraft Caution
Caution: Regulations of the FCC and FAA prohibit airborne operation of
radio-frequency wireless devices because their signals could interfere with
critical aircraft instruments.
Other Wireless Devices
Safety Notices for Other Devices in the Wireless Network: Refer to the
documentation supplied with wireless Ethernet adapters or other devices
in the wireless network.
Canada, Canada-Industry Notice:
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil est conforme aux normes Canada d'Industrie de RSS
permis-exempt. L'utilisation est assujetti aux deux conditions suivantes:
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Caution: When using IEEE 802.11a wireless LAN, this product is restricted
to indoor use due to its operation in the 5.15-to 5.25-GHz frequency
range. Industry Canada requires this product to be used indoors for the
frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for
harmful interference to co-channel mobile satellite systems. High power
radar is allocated as the primary user of the 5.25-to 5.35-GHz and 5.65 to
5.85-GHz bands. These radar stations can cause interference with and/or
damage to this device. The maximum allowed antenna gain for use with
this device is 6dBi in order tocomply with the E.I.R.P limit for the 5.25-to
5.35 and 5.725 to 5.85 GHz frequency range in point-to-point operation. To
comply with RF exposure requirements all antennas should be located at a
minimum distance of 20cm, or the minimum separation distance allowed
by the module approval, from the body of all persons.
Attention: l'utilisation d'un réseau sans l IEEE802.11a est restreinte à
une utilisation en intérieur à cause du fonctionnement dansla bande de
fréquence 5.15-5.25 GHz. Industry Canada requiert que ce produit soit
utilisé à l'intérieur des bâtiments pour la bande de fréquence 5.15-5.25
GHz an de réduire les possibilités d'interférences nuisibles aux canaux
co-existants des systèmes de transmission satellites. Les radars de
puissances ont fait l'objet d'une allocation primaire de fréquences dans
les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces stations radar peuvent
créer des interférences avec ce produit et/ou lui être nuisible. Le gain
d'antenne maximum permissible pour une utilisation avec ce produit est de
6 dBi an d'être conforme aux limites de puissance isotropique rayonnée
équivalente (P.I.R.E.) applicable.
dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz en fonctionnement
point-à-point. Pour se conformer aux conditions d'exposition de RF toutes
les antennes devraient être localisées à une distance minimum de 20 cm,
ou la distance de séparation minimum permise par l'approbation du module,
du corps de toutes les personnes.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be chosen so that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radio électrique à l'intention des
autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte
que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted
by FCC certied equipment. The Intel PRO/Wireless 5000 LAN products meet the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/
IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC's
recommended limits.
The following safety precautions should be observed:
• Do not touch or move antenna while the unit is transmitting or receiving.
• Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face
or eyes, while transmitting.
• Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.
• Use in specic environments:
- The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments.
- The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).
- The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.
Содержание
199- For more product details please visit gigabyte s website
- User s manual
- To reduce the impacts on global warming the packaging materials of this product are recyclable and reusable gigabyte works with you to protect the environment
- Rev 1101 12me z69pro4 1101r
- Z690 aorus pro z690 aorus pro ddr4
- Identifying your motherboard revision
- Documentation classifications
- Disclaimer
- Copyright
- Table of contents
- Chapter 5 appendix 9
- Chapter 4 installing the operating system and drivers 7
- Chapter 3 bios setup 5
- Chapter 2 hardware installation
- Chapter 1 product introduction
- Z690 aorus pro
- Note for debug code information please refer to chapter 5
- Chapter 1 product introduction
- 1 motherboard layout
- Z690 aorus pro ddr4
- Note for debug code information please refer to chapter 5
- Pci express 5 bus
- Pci express 4 bus
- Pci express 3 bus
- Lga1700 cpu
- K only for z690 aorus pro ddr4
- J only for z690 aorus pro
- Cpu clk 80 800 mhz
- 2 motherboard block diagram
- 3 box contents
- Chapter 2 hardware installation
- 1 installation precautions
- 2 product specifications
- A note the cpu orientation
- 3 installing the cpu and cpu cooler
- Follow the steps below to correctly install the cpu into the motherboard cpu socket
- Do not force to engage the cpu socket locking lever when the cpu is not installed correctly as this would damage the cpu and cpu socket
- B installing the cpu
- C installing the cpu cooler
- Be sure to install the cpu cooler after installing the cpu actual installation process may differ depending the cpu cooler to be used refer to the user s manual for your cpu cooler
- Dual channel memory configuration
- 4 installing the memory
- 5 installing an expansion card
- Usb type
- Usb 3 gen 2 type a port red
- Usb 3 gen 1 port
- Usb 2 1 port
- Sma antenna connectors 2t2r
- Rj 45 lan port
- Displayport
- 6 back panel connectors
- Usb 3 gen 2 type a port red q flash plus port
- Optical s pdif out connector
- Mic in
- Line out
- Quick buttons
- Qflash_plus q flash plus button
- 7 onboard buttons and led
- 8 internal connectors
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- Power connector
- 2 atx_12v_2x2 atx_12v_2x4 atx 2x2 2x4 12v power connectors and 2x12 main
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- 4 cpu_fan sys_fan1 2 3 4 fan headers
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- The fan pump headers are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis the header also provides speed control for a water cooling pump please navigate to the bios setup page of gigabyte s website and search for smart fan 6 for more information
- Sys_fan5 6_pump system fan water cooling pump headers
- Overheating overheating may result in damage to the cpu or the system may hang
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design
- Ec_temp1 ec_temp2 temperature sensor headers
- Cpu_opt water cooling cpu fan header
- Connect the thermistor cables to the headers for temperature detection
- Pin no definition
- No pin
- Led_c1 led_c2 rgb led strip headers
- For how to turn on off the lights of the led strip please navigate to the unique features page of gigabyte s website
- D_led1 d_led2 addressable led strip headers
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip
- Connect one end of the rgb led strip extension cable to the header and the other end to your rgb led strip the black wire marked with a triangle on the plug of the extension cable must be connected to pin 1 12v of this header the 12v pin marked with an arrow on the other end of the extension cable must be lined up with the 12v of the led strip be careful with the connection orientation of the led strip incorrect connection may lead to the damage of the led strip
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- The headers can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- The headers can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds
- Types of m ssds supported by each m connector
- There are two types of m ssds m sata ssds and m pcie ssds be sure to verify which type of m ssds is supported by the m socket you want to use please note that an m pcie ssd cannot be used to create a raid set either with an m sata ssd or a sata hard drive please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array
- M2q_sb a a
- M2p_sb a a
- M2c_sb a a a
- M2a_cpu m2c_sb m2p_sb m2q_sb m socket 3 connectors
- M2a_cpu a a
- M pcie x4 ssd m pcie x2 ssd m sata ssd
- Follow the steps below to correctly install an m ssd in the m connector step 1 locate the m connector where you will install the m ssd use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink remove the protective film from the thermal pad on the m connector step 2 locate the proper mounting hole based on the length of your m ssd drive if needed move the standoff to the desired mounting hole insert the m ssd into the m connector at an angle step 3 press the m ssd down and then use the included screw to secure it in the connector remove the protective film from the bottom of the heatsink then replace the heatsink and secure it to the original hole
- The availability of the sata connectors may be affected by the type of device installed in the m sockets the m2c_sb connector shares bandwidth with the sata3 2 3 connector refer to the following table for details
- M2c_sb
- M2a_cpu m2p_sb m2q_sb
- Installation notices for the m and sata connectors
- Bat battery
- Sata3 2 3 4 5 6 7 sata 6gb s connectors
- F_panel front panel header
- Vbus 11 vbus
- No pin
- Usb 0_ b
- Mic detection
- Tx1 13 tx2
- Header with usb 3 gen 2x2 support
- Tx1 12 tx2
- Head phone r
- The header conforms to usb 3 gen 2x2 specification and can provide one usb port
- Head phone l
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- Head phone detection
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer
- Gnd 14 gnd
- F_usb30 f_ u
- Sense_send
- F_usb3 f_usb30 3
- Sbu2 20 cc2
- F_usb3 f
- Sbu1 19 d
- F_u320g usb type
- S b_ b
- F_audio front panel audio header
- S 3 b s s s
- Cc1 18 d
- _ u _ b
- Rx1 16 rx2
- _ s s_ _ b
- Rx1 15 rx2
- B s_ b
- _ s f_
- Pin no definition pin no definition
- Vbus 17 gnd
- Pin no definition
- Pin no definition pin no definition
- Pin no definition
- No pin
- Nc 20 no pin
- Gnd 17 ssrx2
- Gnd 14 sstx2
- Vbus 11 d2
- From the power outlet to prevent damage to the usb bracket
- Usb dy
- F_usb1 f_usb2 usb 2 1 headers
- Usb dx
- F_u32 usb 3 gen 1 header
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer
- D1 19 vbus
- Sstx1 16 gnd
- D1 18 ssrx2
- Sstx1 15 sstx2
- Ssrx1 13 gnd
- Ssrx1 12 d2
- Power 5v
- No pin
- Data output
- Data input
- Chip select
- Add in card connectors
- Add in card
- You may connect an spi tpm trusted platform module to this header
- The connectors are used to connect to a gigabyte thunderbol
- Thb_c1 thb_c2 thunderbol
- Supports a thunderbol
- Spi_tpm trusted platform module header
- Power 3 v
- Pin no definition
- Noise_sensor noise detection header
- Clr_cmos clear cmos jumper
- The status leds show whether the cpu memory graphics card and operating system are working properly after system power on if the cpu dram vga led is on that means the corresponding device is not working normally if the boot led is on that means you haven t entered the operating system yet
- The reset jumper provides you with several functions to use to remap the button to perform different tasks please navigate to the bios setup page of gigabyte s website and search for rst_sw multikey for more information
- The reset jumper can connect to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart
- Rst reset jumper
- Pin no definition
- Cpu dram vga boot status leds
- Cpu cpu status led dram memory status led vga graphics card status led boot operating system status led
- Chapter 3 bios setup
- Startup screen
- Function keys
- Chapter 4 installing the operating system and drivers
- 1 operating system installation
- 2 drivers installation
- Raid levels
- Chapter 5 appendix
- Before you begin please prepare the following items
- 1 configuring a raid set
- Regular boot
- 2 debug led codes
- S3 resume
- Recovery
- United states of america federal communications commission statement
- Regulatory notices
- Wireless module approvals
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com
- Gigabyte esupport
- Contact us
Похожие устройства
-
Gigabyte B760M D3H DDR4Инструкция пользователя -
Gigabyte GA-880GM-D2HИнструкция по работе -
Gigabyte Z890 EAGLEЭксплуатационная инструкция -
Gigabyte Z890 EAGLE WIFI7Инструкция по применению -
Gigabyte H610M S2HРуководство по использованию -
Gigabyte Z790 AORUS MASTER XРуководство по работе с устройством -
Gigabyte B660M GAMINGИнструкция пользователя -
Gigabyte B550M DS3H ACИнструкция по работе -
Gigabyte GA-Q87TNРуководство по настройке -
Gigabyte GA-H87TNИнструкция по работе -
Gigabyte GA-B85TNРуководство пользователя -
Gigabyte GA-H81TNИнструкция по применению
Explore the compliance information and safety notices for wireless devices, including FCC and Industry Canada regulations. Ensure safe operation and adherence to guidelines.