![Gigabyte B650 AERO G — как использовать сброс и замену батареи в компьютере [32/42]](/icons/site-icon-64.png){kind=icon}
Gigabyte B650 AERO G — как использовать сброс и замену батареи в компьютере [32/42]
Превью страниц
Страница 32 /
42
![Gigabyte B650 AERO G Инструкция по эксплуатации онлайн [32/42] 690877](/views2/1919893/page32/bg20.png)
- 32 -
22) RST (Reset Jumper)
The reset jumper can connect to the reset switch on the chassis front panel. Press the reset switch to
restart the computer if the computer freezes and fails to perform a normal restart.
The reset jumper provides you with several functions to use. To remap the button to perform different
tasks, please navigate to the "BIOS Setup" page of GIGABYTE's website and search for "RST_SW
(MULTIKEY)" for more information.
1
Pin No. Denition
1 Reset
2 GND
23) BAT (Battery)
The battery provides power to keep the values (such as BIOS congurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one
minute. (Or use a metal object like a screwdriver to touch the positive
and negative terminals of the battery holder, making them short for
5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
• Always turn off your computer and unplug the power cord before replacing the battery.
• Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model.
• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
• Used batteries must be handled in accordance with local environmental regulations.
F_USB30
F_U
B_
F_ F_
_
B
BS_
B
SB_
B
_S
S_
_
B
_U
_
B
S
123
123
123
123
1
1
1
1
BSS
S
_S
SSU
1 2 3
S3
BSSS
U
__ 3
F_USB3F
S _
S _
S _
SF
B_
B_
F
_0
S
S
_0F
_F
_
_
__B
U
S _S
_
SF_
B
USB0_B
B_
B_
F_USB3
F_USB303
_
_3U
S_
_S
SS_F
_
_
F
_SB
Содержание
221- B650 aero g
- User s manual
- Rev 1001
- Identifying your motherboard revision
- Disclaimer
- Copyright
- Chapter 3 bios setup 4
- Chapter 2 hardware installation
- Table of contents
- Chapter 5 appendix 8
- Chapter 4 installing the operating system and drivers 6
- Chapter 1 product introduction
- B650 aero g
- 1 motherboard layout
- Chapter 1 product introduction
- S pdif out
- Pci express 5
- Pci express 4 bus
- Pci express 3 bus
- Note actual support may vary by cpu
- Line out
- Cpu clk 100 mhz
- Amd chipset
- Am5 cpu
- 2 motherboard block diagram
- 3 box contents
- Chapter 2 hardware installation
- 1 installation precautions
- 2 product specifications
- 2 productspecifications
- A note the cpu orientation
- 3 installing the cpu and cpu cooler
- Follow the steps below to correctly install the cpu into the motherboard cpu socket
- Do not force to engage the cpu socket locking lever when the cpu is not installed correctly as this would damage the cpu and cpu socket
- B installing the cpu
- C installing the cpu cooler
- Be sure to install the cpu cooler after installing the cpu actual installation process may differ depending the cpu cooler to be used refer to the user s manual for your cpu cooler
- Dualchannelmemoryconfiguration
- 4 installing the memory
- 5 installing an expansion card
- Usb 2 1 port
- Sma antenna connectors 2t2r
- Hdmi port
- Displayport in port
- 6 back panel connectors
- Usb 3 gen 2 type a port red
- Line out front speaker out
- Usb type
- Usb 3 gen 2 type a port q flash plus port
- Usb 3 gen 1 port
- Rj 45 lan port
- Port with usb 3 gen 2 support
- Optical s pdif out connector
- Mic in rear speaker out
- Qflash_plus q flash plus button
- Quick buttons
- 7 onboard buttons
- The status leds show whether the cpu memory graphics card and operating system are working properly after system power on if the cpu dram vga led is on that means the corresponding device is not working normally if the boot led is on that means you haven t entered the operating system yet
- Status leds
- 8 internal connectors
- 2 atx_12v_2x2 atx_12v atx 2x2 2x4 12v power connectors and 2x12 main power connector
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers
- The fan pump headers are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis the header also provides speed control for a water cooling pump please navigate to the bios setup page of gigabyte s website and search for smart fan 6 for more information
- Sys_fan5 6_pump system fan water cooling pump headers
- Overheating overheating may result in damage to the cpu or the system may hang
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis
- 4 cpu_fan sys_fan1 2 3 4 fan headers
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design
- Ec_temp1 ec_temp2 temperature sensor headers
- Cpu_opt water cooling cpu fan header
- Connect the thermistor cables to the headers for temperature detection
- Connect your addressable led strip to the header the power pin marked
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- With a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip
- Triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip
- The headers can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- The headers can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds
- Pin no definition
- No pin
- Led_c1 led_c2 rgb led strip headers
- For how to turn on off the lights of the led strip please navigate to the unique features page of gigabyte s website
- D_led1 d_led2 addressable led strip headers
- Connect your rgb led strip to the header the power pin marked with a
- Sata3 0 1 2 3 sata 6gb s connectors
- Power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip
- For how to turn on off the lights of the led strip please navigate to the unique features page of gigabyte s website
- Cpu_led cpu cooler led strip rgb led strip header
- Connect the cpu cooler led strip rgb led strip to the header the
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices
- To enable hot plugging for the sata ports please navigate to the bios setup page of gigabyte s website and search for sata configuration for more information
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the sata connectors support raid 0 raid 1 and raid 10 please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array
- The header can be used to connect a cpu cooler led strip or a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m
- Step 2 insert the m ssd into the m connector at an angle press down on the front end of the m ssd and close m ez latch clip to secure the m ssd step 3 remove the protective film from the bottom of the motherboard heatsink and then replace the heatsink and tighten the screws diagonally
- Standoff be sure to remove the ez latch clip first and use the motherboard heatsink screw to secure the heatsink and ssd
- Please visit gigabyte s website for details on using m ez latch
- M2c_sb a a
- M2b_cpu a a
- M2a_cpu m2b_cpu m2c_sb m socket 3 connectors
- M2a_cpu a a
- M pcie x4 ssd m pcie x2 ssd m sata ssd
- Install the m ssd https www gigabyte com webpage 919 m2 ezlatch html
- If you want to install an m ssd that came with its own heatsink you have to remove the
- If you want install an m ssd in the 110mm hole that already has a motherboard heatsink
- Follow the steps below to correctly install an m ssd in the m connector step 1 unfasten the screws on the motherboard heatsink diagonally to remove the heatsink select the m slot you want to use and press down on the m ez latch clip to open it
- Ez latch clip first and use the provided screw and standoff to fasten the ssd
- Types of m ssds supported by each m connector
- There are two types of m ssds m sata ssds and m pcie ssds this motherboard only supports m pcie ssds please note that an m pcie ssd cannot be used to create a raid set with a sata hard drive please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array
- F_panel front panel header
- Usb 0_ b
- Mic detection
- Tx1 13 tx2
- Header with usb 3 gen 2x2 support
- Tx1 12 tx2
- Head phone r
- The header conforms to usb 3 gen 2x2 specification and can provide one usb port
- Head phone l
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it
- Head phone detection
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer
- Gnd 14 gnd
- Sense_send
- F_usb30 f_ u
- Sbu2 20 cc2
- F_usb3 f_usb30 3
- Sbu1 19 d
- F_usb3 f
- S b_ b
- F_u320g usb type
- S 3 b s s s
- F_audio front panel audio header
- Rx1 16 rx2
- Cc1 18 d
- _ u _ b
- Rx1 15 rx2
- B s_ b
- _ s s_ _ b
- Pin no definition pin no definition
- _ s f_
- Pin no definition
- Vbus 17 gnd
- No pin
- Vbus 11 vbus
- Pin no definition
- No pin
- Nc 20 no pin
- Gnd 17 ssrx2
- Gnd 14 sstx2
- From the power outlet to prevent damage to the usb bracket
- Vbus 11 d2
- F_usb1 f_usb2 usb 2 1 headers
- Usb dy
- F_u32 usb 3 gen 1 header
- Usb dx
- Do not plug the ieee 1394 bracket 2x5 pin cable into the usb 2 1 header prior to installing the usb bracket be sure to turn off your computer and unplug the power cord
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer
- D1 19 vbus
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer
- Sstx1 16 gnd
- D1 18 ssrx2
- Sstx1 15 sstx2
- Ssrx1 13 gnd
- Ssrx1 12 d2
- Power 5v
- Pin no definition pin no definition
- No pin
- Data output
- Data input
- Com serial port header
- Chip select
- You may connect an spi tpm trusted platform module to this header
- The com header can provide one serial port via an optional com port cable for purchasing the optional com port cable please contact the local dealer
- Spi_tpm trusted platform module header
- Power 3 v
- Pin no definition
- Use this jumper to clear the bios configuration and reset the cmos values to factory defaults to clear the cmos values use a metal object like a screwdriver to touch the two pins for a few seconds
- This connector is for a gigabyte add in card
- The cmos values
- Thb_u4 add in card connector
- Short clear cmos values
- Open normal
- Manually configure the bios settings please navigate to the bios setup page of gigabyte s website for more information
- Clr_cmos clear cmos jumper
- Always turn off your computer and unplug the power cord from the power outlet before clearing
- After system restart go to bios setup to load factory defaults select load optimized defaults or
- You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is
- When installing the battery note the orientation of the positive side and the negative side
- Used batteries must be handled in accordance with local environmental regulations
- The reset jumper provides you with several functions to use to remap the button to perform different tasks please navigate to the bios setup page of gigabyte s website and search for rst_sw multikey for more information
- The reset jumper can connect to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost
- Rst reset jumper
- Replaced with an incorrect model
- Replace the battery 4 plug in the power cord and restart your computer
- Pin no definition
- Or uncertain about the battery model
- Of the battery the positive side should face up
- Minute or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
- Bat battery
- Noise_sensor noise detection header
- Chapter 3 bios setup
- Function keys
- Startup screen
- Chapter 4 installing the operating system and drivers
- 1 operating system installation
- 2 drivers installation
- Raid levels
- Chapter 5 appendix
- Before you begin please prepare the following items
- 1 configuringaraidset
- 1 configuring a raid set
- United states of america federal communications commission statement
- Regulatory notices
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com
- Gigabyte esupport
- Contact us
Похожие устройства
-
Gigabyte B760M D3H DDR4Инструкция пользователя -
Gigabyte GA-880GM-D2HИнструкция по работе -
Gigabyte Z890 EAGLEЭксплуатационная инструкция -
Gigabyte Z890 EAGLE WIFI7Инструкция по применению
-
Gigabyte H610M S2HРуководство по использованию -
Gigabyte Z790 AORUS MASTER XРуководство по работе с устройством -
Gigabyte B660M GAMINGИнструкция пользователя -
Gigabyte B550M DS3H ACИнструкция по работе -
Gigabyte GA-Q87TNРуководство по настройке -
Gigabyte GA-H87TNИнструкция по работе
-
Gigabyte GA-B85TNРуководство пользователя
-
Gigabyte GA-H81TNИнструкция по применению
Узнайте, как правильно использовать сброс компьютера и замену батареи для сохранения настроек BIOS. Подробные инструкции и советы по безопасности.