Gigabyte A520M K V2 — установка и замена батареи CMOS: пошаговое руководство [22/30]

Содержание

• A520m k a520m k v2 p.1
• User s manual p.1
• Rev 1002 p.1
• Disclaimer p.2
• Copyright p.2
• Identifying your motherboard revision p.2
• Chapter 2 hardware installation p.3
• Chapter 3 bios setup 4 p.3
• Chapter 1 product introduction p.3
• Chapter 4 installing the operating system and drivers 6 p.3
• Table of contents p.3
• Chapter 5 appendix 8 p.3
• A520m k a520m k v2 p.4
• 1 motherboard layout p.4
• J only for a520m k v2 p.4
• Chapter 1 product introduction p.4
• 2 box contents p.5
• 1 installation precautions p.6
• Chapter 2 hardware installation p.6
• 2 product specifications p.7
• 2 productspecifications p.7
• Installing the cpu p.10
• 3 installing the cpu p.10
• 4 installing the memory p.11
• Dualchannelmemoryconfiguration p.11
• 5 installing an expansion card p.12
• 6 back panel connectors p.13
• Usb 2 1 port p.13
• Usb 3 gen 1 port p.13
• Rj 45 lan port p.13
• Hdmi port p.13
• Ps 2 keyboard mouse port p.13
• D sub port p.13
• Line in rear speaker out blue p.14
• Audio jack configurations p.14
• Line out front speaker out green p.14
• The mic in jack p.14
• The line out jack p.14
• The line in jack use this audio jack for line in devices such as an optical drive walkman etc p.14
• Please visit gigabyte s website for details on configuring the audio software p.14
• Mic in center subwoofer speaker out pink p.14
• You can change the functionality of an audio jack using the audio software to configure 7 channel audio access the audio software for audio settings p.14
• 7 internal connectors p.15
• 2 atx_12v atx 2x4 12v power connector and 2x12 main power connector p.16
• With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation p.16
• The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start p.16
• To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system p.16
• Sata3 0 1 2 3 sata 6gb s connectors p.17
• 4 cpu_fan sys_fan1 fan headers p.17
• The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the sata connectors support raid 0 raid 1 and raid 10 please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array p.17
• These fan headers are not configuration jumper blocks do not place a jumper cap on the headers p.17
• Be sure to connect fan cables to the fan headers to prevent your cpu and system from p.17
• All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the motherboard supports cpu fan speed control which requires the use of a cpu fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis p.17
• Overheating overheating may result in damage to the cpu or the system may hang p.17
• M2a_cpu m socket 3 connector p.18
• The m connector supports m sata ssds or m pcie ssds and support raid configuration please note that an m pcie ssd cannot be used to create a raid set with a sata hard drive please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array p.18
• Follow the steps below to correctly install an m ssd in the m connector step 1 pull the clip s tab up and out of the mounting hole slide the m ssd into the connector at an angle step 2 press the m ssd down and then secure it by pressing the clip s tab into the mounting hole p.18
• F_panel front panel header p.19
• Speaker speaker header p.20
• Connects to the speaker on the chassis front panel the system reports system startup status by issuing a beep code one single short beep will be heard if no problem is detected at system startup p.20
• The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it p.20
• Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer p.20
• F_audio front panel audio header p.20
• Power 5v 6 usb dy p.21
• Power 5v 7 gnd p.21
• F_usb1 f_usb2 usb 2 1 headers p.21
• The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer p.21
• Sstx1 16 gnd p.21
• Pin no definition pin no definition p.21
• Nc 20 no pin p.21
• F_u32 usb 3 gen 1 header p.21
• Usb dx 8 gnd p.21
• D1 19 vbus p.21
• Usb dx 10 nc p.21
• D1 18 ssrx2 p.21
• The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer p.21
• Sstx1 15 sstx2 p.21
• Ssrx1 13 gnd p.21
• Ssrx1 12 d2 p.21
• Prior to installing the usb bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the usb bracket p.21
• Gnd 17 ssrx2 p.21
• Gnd 14 sstx2 p.21
• Vbus 11 d2 p.21
• Usb dy 9 no pin p.21
• You may clear the cmos values by removing the battery 1 turn off your computer and unplug the power cord 2 gently remove the battery from the battery holder and wait for one p.22
• Replaced with an incorrect model p.22
• Of the battery the positive side should face up p.22
• No pin 10 nc p.22
• Lad0 7 lad3 p.22
• Tpm trusted platform module header p.22
• Replace the battery 4 plug in the power cord and restart your computer p.22
• Pin no definition pin no definition p.22
• Or uncertain about the battery model p.22
• Minute or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds p.22
• Lclk 12 lreset p.22
• Lad2 11 serirq p.22
• Lad1 9 lframe p.22
• You may connect a tpm trusted platform module to this header p.22
• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself p.22
• When installing the battery note the orientation of the positive side and the negative side p.22
• Bat battery p.22
• Vcc3 8 gnd p.22
• Used batteries must be handled in accordance with local environmental regulations p.22
• Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is p.22
• The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost p.22
• Clr_cmos clear cmos jumper p.23
• Ci chassis intrusion header p.23
• Chapter 3 bios setup p.24
• Startup screen p.25
• Function keys p.25
• Chapter 4 installing the operating system and drivers p.26
• 1 operating system installation p.26
• 2 drivers installation p.27
• Chapter 5 appendix p.28
• 1 configuring a raid set p.28
• 1 configuringaraidset p.28
• Raid levels p.28
• Before you begin please prepare the following items p.28
• United states of america federal communications commission statement p.29
• Regulatory notices p.29
• Gigabyte esupport p.30
• Contact us p.30
• To submit a technical or non technical sales marketing question please link to https esupport gigabyte com p.30