Home
Главная
Vitek
Соковыжималки
VT-1614 ST
Руководство по эксплуатации Страница: 4

Vitek VT-1614 ST [4/38] English

ENGLISH

Making juice

Before the first plugging in make sure that the

operating voltage of the unit corresponds to volt-

age of your mains.

Fruit and vegetables meant for processing must

be fresh.

Before juice extracting remove inedible parts

from vegetables or fruit, such as stems, hard peel

or stones, for example, cherry or peach.

Wash fruit/vegetables and chop them into pieces

easily fitting into the feeding chute (2).

– Place the motor unit (9) on a dry, flat and

steady surface.

– Before unit assembling make sure that the

operation modes switch is set in the posi-

tion «0», and the plug is not inserted into the

socket.

– Set juice collector (6) on the motor unit (9).

– Install mesh filter (5) in the juice collector (6).

– Install grating filter (4) into the mesh filter (5).

Note: Do not use juice extractor if you found

mechanical damages of grating filter (4) or mesh

filter (5).

– Install the lid (3) on the juice collector (6) and

fix it with by placing the locking arm (8) in ver-

tical position.

– Install pulp container (11) in its place.

– Open the juice cup (14) lid (12) and install the

separator (13) in it.

– Put the juice cup (14) under the juice drain-

ing spout (7).

– Insert the plug into the socket.

– Switch juice extractor on by setting the switch

(10) to the position «I» (low speed) or to posi-

tion «II» (high speed).

Note:

Mode «I» (low speed) is intended for juice

extracting from soft vegetables/fruits - such

as tomatoes, ripe pears, strawberry, oranges,

plums, grapes, pumpkin, onion, cucumbers and

etc.

Mode «II» (high speed) is intended for juice

extracting from hard vegetables/fruits - such as

artichoke, carrot, apples, pepper, beets, pota-

toes, pineapples, vegetable marrows, celery,

spinach, dill, leek etc.

Attention! During processing of viscous or quite

hard foods in order to avoid the grating filter (4)

stopping and motor unit jamming it is recom-

mended to use the high speed «II» mode of juice

extractor operation.

– The unit will switch on only if all the remov-

able parts are installed properly, and the lid

(3) is fixed with the locking arm (8).

– Feed fruit/vegetable pieces into the lid (3)

feeding chute (2), only when grating filter (4)

is rotating.

– Put vegetables or fruits cut beforehand grad-

ually into the lid (3) feeding chute (2) and

push them gently with the pusher (1). Do

not press on the pusher (1) too hard as it

can lead to decrease of juice amount as well

as to grating filter (4) rotation stopping. The

slower fruit and vegetables processing, the

higher juice extraction rate.

– Do not put your fingers or any other foreign

objects into the lid (3) feeding chute (2).

– During operation process check the grating

filter (4) and mesh filter (5) periodically for

obstruction of mesh with pulp, if necessary

wash the grating filter (4) and mesh filter (5),

switch juice extractor off and unplug it before

removing the filters.

– Control the pulp container filling (11), if the

container (11) is filled up, switch juice extrac-

tor off, unplug it and remove the pulp from

the container (11).

ATTENTION: The maximal allowable con-

tinuous operation time is not more than 2

minutes with subsequent break of at least

3 minutes.

– After unit operation, switch it off by set-

ting the switch (10) in the position «0», and

unplug it.

Cleaning and maintenance

After the end of operation or before cleaning

always switch juice extractor off and unplug it.

Disassemble and clean juice extractor after

every usage:

• Remove the pusher (1) from the lid (3) feed-

ing chute (2).

• Lower the locking arm and release the lid (3).

• Remove the lid (3).

• Remove juice collector (6) with the mesh fil-

ter (5) and grating filter (4).

– It is recommended to wash all removable

parts in warm water with neutral detergent

right after unit operation.

– It is more convenient to wash grating filter

(4) and mesh filter (5) slots from the outside

using a small brush.

VT-1614 IM.indd 4 14.03.2012 14:44:56

Vitek VT-1614 ST [4/38] English

Содержание

Похожие устройства