![Vdo Z2 Руководство по эксплуатации онлайн [21/57] 736377](/img/pdf.png)
Vdo Z2 Руководство по эксплуатации онлайн [21/57] 736377
![Vdo Z2 Руководство по эксплуатации онлайн [21/57] 736377](/views2/1966374/page21/bg15.png)
12
EN
2, and the altitude difference walked. Reprogram this information after
inserting the new batteries.
2.1.2 BATTERY INSTALLATION PULSE-CHEST BELT >>> P03
Your VDO is shipped with the battery installed in the pulse-chest belt.
Proceed as follows when later inserting a replacement battery:
step 1 Insert the battery into the chest-belt housing with the +pole up.
step 2 Ensure that the battery is not tilted.
step 3 Strictly ensure that the rubber seal lies smoothly on the battery
compartment lid.
step 4 Insert the battery compartment lid into the opening and use
a coin to firmly turn the battery door to right until the stop
(approximately 1/3 turn)
2.2. INSTALLATION - HOLDER/COMPUTER/TRANSMITTER/MAGNET
a. Holder >>> P04 / 05: Your VDO computer is shipped with a universal
handlebar holder.
step 1 You can mount the holder either on the handlebar or the stem.
If you are installing the holder on the handlebar decide whether
you want it on the right side or the left side. If installing on the
stem, loosen the screws in the holder and turn the foot of the
holder to stem installation. Then screw the foot firmly onto the
holder again.
step 2 Route the cable ties through the provided eyes of the holder
foot and pull both of them tight.
b. Computer
>>> P06
The VDO twist-click system securely connects the computer to the
handlebar holder.
step 1 Insert the computer, turned to the left approximately 45
degrees (10 o‘clock position) into the holder.
step 2 Twist the computer to the right until it audibly engages (clicks)
in the holder system (12 o‘clock position).
step 3 To remove the computer turn it to the left (do not press or pull).
c. Speed transmitter and magnet
>>> P07
Mount the transmitter on the same side of the handlebar that the com-
puter is mounted on. If you have installed the holder on the stem then
we recommend mounting the transmitter on the left side.
step 1 Loosely fasten the transmitter on the fork with cable ties (do
not tighten).
step 2 Place the spoke magnet on a spoke
step 3 Align the spoke magnet to the transmitter marking with a
clearance of approximately 3 mm and click it together.
step 4 Align transmitter and magnet relative to each other and tighten
the cable tie on the transmitter.
Please pay attention to the maximum distances:
- Maximum transmitter-computer distance = 120 cm
- Transmitter-magnet distance: 3 mm to a maximum of 10 mm
Содержание
- For cycling 1
- Vdo series z 1
- My settings 2
- Open close 4
- Picturebook picturebook 4
- Picturebook 5
- Picturebook 9
- Picturebook 11
- Ws in mm inch 11
- Picturebook 12
- Instruction manual 14
- Instruction manual 16
- Displaying all pulse measurement functions and interval data stored 17
- Displaying the bike functions 1 displaying the bike functions 2 17
- Manual start stop of the stopwatch and of all other timers 17
- Not in walk mode 17
- Not used in operation mode 17
- Operation mode use this mode to display all information button assignment is shown on the housing 17
- In set mode number fl ashes reduce number page up within the menu level ƒ in set mode number fl ashes increase number after subsequent confi rmation of a setting the computer automatically returns to operation mode 18
- Instruction manual 18
- Setting mode use this mode to make all settings the assignment of buttons is on the buttons 18
- To go to setting mode press button ç for 3 seconds 18
- Å once last step or back one menu level hold return to start menu select confi rm displayed option in the highest menu level select the next menu level page down within the menu level 18
- Instruction manual 20
- Instruction manual 22
- Instruction manual 24
- Instruction manual 26
- Instruction manual 28
- Instruction manual 30
- Instruction manual 32
- Instruction manual 34
- Instruction manual 36
- Instruction manual 38
- Instruction manual 40
- Instruction manual 42
- Instruction manual 44
- Instruction manual 46
- Eu declaration of conformity we cycle parts gmbh grosse ahlmuehle 33 d 76865 rohrbach declare under our responsibility that the products vdo z1 z2 z3 z2 pc link z3 pc link and all transmitters z cad z pulse z sender dockingstation are compliant with the essential requirements and other relevant requirements of the r tte directive 1999 5 ec the declaration of conformity can be found at www vdocyclecomputer com 54
- Eu konformitätserklärung wir cycle parts gmbh grosse ahlmuehle 33 d 76865 rohrbach erklären dass die vdo fahrradcompu ter mit funkübertragung vdo z1 z2 z3 z2 pc link z3 pc link und alle sender z cad z pulse z sender dockingstation bei bestimmungsgemäßer verwendung den grundlegenden anforderungen gemäß artikel 3 der r tte richtlinie 1999 5 eg entsprechen die konformitäts erklärung finden sie unter www vdocyclecomputing com 54
- Rohrbach februar 2008 h j noenen 54
- Addendum to user manual 55
- Addendum to user manual 56
- Vdo series z 57
Похожие устройства
- Vdo Z3 Руководство по эксплуатации
- Velomann V1 07 Инструкция по эксплуатации
- Velomann V1 16 Инструкция по эксплуатации
- Velomann V1 23 Инструкция по эксплуатации
- Syma S107H Руководство по эксплуатации
- Syma S5H Руководство по эксплуатации
- Syma TF1001 Руководство по эксплуатации
- Syma W1 Pro Инструкция по эксплуатации
- Syma X12 Nano Руководство по эксплуатации
- Syma X15 Руководство по эксплуатации
- Syma X15A Руководство по эксплуатации
- Syma X15W Руководство по эксплуатации
- Syma X20 Руководство по эксплуатации
- Syma X20-S Руководство по эксплуатации
- Syma X20P Руководство по эксплуатации
- Syma X20W Руководство по эксплуатации
- Syma X21 Руководство по эксплуатации
- Syma X22S Руководство по эксплуатации
- Syma X22SW Руководство по эксплуатации
- Syma X22W Руководство по эксплуатации