![Aten VE8950T [15/17] Network setup examples](/img/pdf.png)
Aten VE8950T [15/17] Network setup examples
![Aten VE8900T [15/17] Network setup examples](/views2/1977746/page15/bgf.png)
4.4 Network Setup Examples
One Transmitter to One Receiver
A single transmitter and receiver can be linked directly or via the
LAN, to send video from a source to a display in another location.
If linked directly the CAT5e/6 cable linking them should not run
more than 100m/328ft.
The devices will not automatically connect and must first be
selected receiver. The ID number must match with transmitter ID
number to establish the link.
One Transmitter to Multiple Receivers
Using VE8900 / VE8950 / VE8952 for one-to-many installations dramatically decreases the amount of
equipment required at the source location, each transmitter can be located up to 100m/355ft from the
switch.
Scenario A (with Ethernet switch)
Содержание
- Implementation guide p.1
- Aten hdmi over ip video extender system p.1
- Contents p.2
- Introduction p.3
- Ve8900 ve8950 ve8952 series p.4
- Engineered to meet the demands of today s large scale multi display 1080p 4k signal transmission requirements but designed to be uncomplicated to set up and easy to use the ve8900 ve8950 ve8952 is suitable for use in a wide range of environments including trade shows airports university campuses conference centers and shopping centers p.5
- General recommendations p.6
- Supported video resolutions p.7
- Source display settings p.7
- Aten ve8900 ve8950 ve8952 uses the highest quality encoders available to provide visually lossless compression over a large number of displays however the compression can only be as good as the source content that is put in ve8900 ve8950 ve8952 uses proprietary compression and supports hdcp 1 thus please make sure the source content supports hdcp1 or is without hdcp encryption not compatible with hdcp2 in addition please make sure to turn off the video wall function of the display p.7
- Network design p.8
- Choosing the right cable p.8
- Choosing a network switch p.9
- Standalone network switch p.11
- Recommended switches the following models have been tested and found to produce favorable results separate to two target application p.11
- Cascading aggregation network switch p.11
- Planning network architecture p.12
- Network setup examples p.15
- Pick an appropriate forwarding mode on all switches use cut through if available or store and p.17
- Igmp and other settings configuring the switch correctly will pass data more efficiently allowing a better stream across the network to each ve device the following settings will help optimize your network traffic through a switch enable igmp snooping on l2 switches enable igmp querier on the l3 switch enable igmp fast leave on all switches where ve units are directly connected enable jumbo frames jumbo packets in order to correctly convey the necessary data enable spanning tree protocol stp on all switches and enable portfast exclusively on switch ports p.17
- Forward p.17
- Configuring the network switch p.17
- The following table shows the recommended settings for various networking topologies the following table shows the recommended settings for various networking topologies p.17
- That have ve units connected p.17
Похожие устройства
-
Aten VE1843Руководство пользователя -
Aten VE1843Краткое руководство по установке -
Aten VE849TРуководство пользователя -
Aten VE849TКраткое руководство по установке -
Aten VE883TРуководство пользователя -
Aten VE883TКраткое руководство по установке -
Aten VE2812EUTРуководство пользователя -
Aten VE2812EUTКраткое руководство по установке -
Aten VE2812AEUTРуководство пользователя -
Aten VE2812AEUTКраткое руководство по установке -
Aten VE2812AUSTРуководство пользователя
-
Aten VE2812AUSTКраткое руководство по установке