![Aten VE8950R [7/17] Supported video resolutions](/img/pdf.png)
Aten VE8950R [7/17] Supported video resolutions
![Aten VE8950R [7/17] Supported video resolutions](/views2/1977746/page7/bg7.png)
Source & Display Settings
ATEN VE8900 / VE8950 / VE8952 uses the highest quality encoders available to provide visually
lossless compression over a large number of displays. However, the compression can only be as good
as the source content that is put in. VE8900 / VE8950 / VE8952 uses proprietary compression and
supports HDCP 1.4. Thus, please make sure the source content supports HDCP1.4 or is without
HDCP encryption. (NOT compatible with HDCP2.2) In addition, please make sure to turn off the video
wall function of the display.
Supported Video Resolutions
Resolution
Refresh Rate
Support Model
720x240P
60Hz
VE8900 / VE8950 /
VE8952
720x288p
50Hz
480i
50/60Hz
120Hz
480P
60Hz
120Hz
1440x480P
60Hz
576i
50/100Hz
576P
50/60/100Hz
720P
(1280x720p/1680x720p)
24/25/30/50/60Hz
1080i
50/60Hz
1080p
(1920x1080p/2560x1080p)
24/25//30/50/60Hz
2160p
(3840x2160p/4096x2160p)
24/25/30/50/60Hz
VE8950 / VE8952
Содержание
- Implementation guide p.1
- Aten hdmi over ip video extender system p.1
- Contents p.2
- Introduction p.3
- Ve8900 ve8950 ve8952 series p.4
- Engineered to meet the demands of today s large scale multi display 1080p 4k signal transmission requirements but designed to be uncomplicated to set up and easy to use the ve8900 ve8950 ve8952 is suitable for use in a wide range of environments including trade shows airports university campuses conference centers and shopping centers p.5
- General recommendations p.6
- Supported video resolutions p.7
- Source display settings p.7
- Aten ve8900 ve8950 ve8952 uses the highest quality encoders available to provide visually lossless compression over a large number of displays however the compression can only be as good as the source content that is put in ve8900 ve8950 ve8952 uses proprietary compression and supports hdcp 1 thus please make sure the source content supports hdcp1 or is without hdcp encryption not compatible with hdcp2 in addition please make sure to turn off the video wall function of the display p.7
- Network design p.8
- Choosing the right cable p.8
- Choosing a network switch p.9
- Standalone network switch p.11
- Recommended switches the following models have been tested and found to produce favorable results separate to two target application p.11
- Cascading aggregation network switch p.11
- Planning network architecture p.12
- Network setup examples p.15
- The following table shows the recommended settings for various networking topologies the following table shows the recommended settings for various networking topologies p.17
- That have ve units connected p.17
- Pick an appropriate forwarding mode on all switches use cut through if available or store and p.17
- Igmp and other settings configuring the switch correctly will pass data more efficiently allowing a better stream across the network to each ve device the following settings will help optimize your network traffic through a switch enable igmp snooping on l2 switches enable igmp querier on the l3 switch enable igmp fast leave on all switches where ve units are directly connected enable jumbo frames jumbo packets in order to correctly convey the necessary data enable spanning tree protocol stp on all switches and enable portfast exclusively on switch ports p.17
- Forward p.17
- Configuring the network switch p.17
Похожие устройства
-
Aten VE849RРуководство пользователя -
Aten VE849RКраткое руководство по установке -
Aten VE883RРуководство пользователя -
Aten VE883RКраткое руководство по установке -
Aten VE801RКраткое руководство по установке -
Aten VE805RКраткое руководство по установке -
Aten VE813AКраткое руководство по установке -
Aten VE813AРуководство пользователя -
Aten VE1812RКраткое руководство по установке -
Aten VE1812RРуководство пользователя -
Aten VE1812TКраткое руководство по установке
-
Aten VE1812TРуководство пользователя