Home
Главная
Maxwell
Утюг
MW-3055 B
Инструкция по эксплуатации Страница: 11

Maxwell MW-3055 B [11/36] English

ENGLISH

WATER SELECTION

Use tap water to fill the tank. If tap water is hard,

it is recommended to mix it with distilled water in

proportion 1:1, if tap water is too hard, mix it with

distilled water in proportion 1:2 or use distilled

water only.

FILLING THE WATER TANK

Before filling the tank with water, make sure that

the unit is unplugged.

– Set the temperature control knob (11) to the

«MIN» position and the continuous steam

supply knob (3) to the position

•

(steam sup-

ply is off).

– Open the water inlet lid (2).

– Pour the water into the water tank (10) and

then close the lid (2).

Notes:

• Do not fill the water tank (10) with scented

liquids, vinegar, starch solution, descaling

reagents, chemical agents etc.

• Do not exceed the «MAX» mark (13).

• If you need to refill water during ironing,

switch the iron off and unplug it.

IRONING TEMPERATURE

– Always check the recommended ironing

temperature indicated on the tag before

ironing.

– If there is no tag with recommended ironing

temperature, but you know the type of fab-

ric, use the following table to determine the

proper ironing temperature.

Symbol Fabric type (temperature)

•

Synthetics, nylon, acrylic,

polyester (low temperature)

••

Silk/wool (medium temperature)

•••

Cotton, linen (high temperature)

MAX

Maximum temperature

– This table is only valid for smooth materials.

Other types of fabrics (crimped, raised etc.)

should be ironed at low temperature.

– Sort items by ironing temperature first: syn-

thetics to synthetics, wool to wool, cotton to

cotton etc.

– The iron heats up faster than it cools down.

For this reason it is recommended to begin

ironing at low temperature (for instance, syn-

thetic fabrics).

– After that, start ironing at higher temperature

(silk, wool). Cotton and linen items should be

ironed last.

– If an item is made of mixed fabrics, the iron

should be set to the lowest temperature (for

instance, if an item is made from acrylic and

cotton, it should be ironed at temperature

used for acrylic ironing «

•

»).

– If you cannot define the fabric structure,

find a place that is hidden while wearing and

select the ironing temperature experimen-

tally (always start with the lowest tempera-

ture and raise it gradually until you get the

desired result).

– Corduroy and other fabrics that become

glossy quickly should be ironed strictly in one

direction (in the direction of the pile) with little

pressure.

– To avoid appearance of glossy spots on

synthetic and silk fabrics, iron them back-

side.

DRY IRONING

– Place the iron on its base (8).

– Insert the power plug into the mains socket.

– Set the continuous steam supply knob (3)

to the «

•

» position (continuous steam sup-

ply is off).

– Set the desired temperature of ironing

depending on the type of fabric by turning

the knob (11): «

•

», «

••

», «

•••

» or «MAX»,

the pilot lamp (9) will light up.

– Once the soleplate (14) reaches the set tem-

perature, the pilot lamp (9) will go out and

you can start ironing.

– After you finish ironing set the temperature

control knob (11) to the «MIN» position.

– Pull the power plug out of the mains socket

and let the iron cool down completely.

STEAM IRONING

Steam ironing is possible only if the temperature

control knob (11) is set to the position «

••

»,

•••

» or «MAX».

– Place the iron on its base (8).

– Insert the power plug into the mains socket.

– Make sure that there is enough water in the

water tank (10).

– Turn the control knob (11) to set the required

ironing temperature: «

••

», «

•••

» or «MAX»,

the pilot lamp (9) will light up.

MW-3055.indd 11 11.02.2014 14:29:22

Maxwell MW-3055 B [11/36] English

Содержание

Похожие устройства